Search NASA⌕ Search

Engineering topics

Savage, M.

Publications and source records attributed to Savage, M..

At least 37 records · Page 2

Maximum life spur gear design

Optimization procedures allow one to design a spur gear reduction for maximum life and other end use criteria. A modified feasible directions search algorithm permits a wide variety of inequality constraints and exact design requirements to be met with low sensitivity to initial guess values. The optimization algorithm is described, and the models for gear life and performance are presented. The algorithm is compact and has been programmed for execution on a desk top computer. Two examples are presented to illustrate the method and its application.

Savage, M.↗

Computing Lives And Reliabilities Of Turboprop Transmissions

Computer program PSHFT calculates lifetimes of variety of aircraft transmissions. Consists of main program, series of subroutines applying to specific configurations, generic subroutines for analysis of properties of components, subroutines for analysis of system, and common block. Main program selects routines used in analysis and causes them to operate in desired sequence. Series of configuration-specific subroutines put in configuration data, perform force and life analyses for components (with help of generic component-property-analysis subroutines), fill property array, call up system-analysis routines, and finally print out results of analysis for system and components. Written in FORTRAN 77(IV).

Coy, J. J.↗

Effects of rim thickness on spur gear bending stress

Thin rim gears find application in high-power, light-weight aircraft transmissions. Bending stresses in thin rim spur gear tooth fillets and root areas differ from the stresses in solid gears due to rim deformations. Rim thickness is a significant design parameter for these gears. To study this parameter, a finite element analysis was conducted on a segment of a thin rim gear. The rim thickness was varied and the location and magnitude of the maximum bending stresses reported. Design limits are discussed and compared with the results of other researchers.

Bibel, G. D.↗

Maximum life spur gear design

Optimization procedures allow one to design a spur gear reduction for maximum life and other end use criteria. A modified feasible directions search algorithm permits a wide variety of inequality constraints and exact design requirements to be met with low sensitivity to initial guess values. The optimization algorithm is described, and the models for gear life and performance are presented. The algorithm is compact and has been programmed for execution on a desk top computer. Two examples are presented to illustrate the method and its application.

Savage, M.↗

Transmission overhaul estimates for partial and full replacement at repair

Timely transmission overhauls increase in-flight service reliability greater than the calculated design reliabilities of the individual aircraft transmission components. Although necessary for aircraft safety, transmission overhauls contribute significantly to aircraft expense. Predictions of a transmission's maintenance needs at the design stage should enable the development of more cost effective and reliable transmissions in the future. The frequency is estimated of overhaul along with the number of transmissions or components needed to support the overhaul schedule. Two methods based on the two parameter Weibull statistical distribution for component life are used to estimate the time between transmission overhauls. These methods predict transmission lives for maintenance schedules which repair the transmission with a complete system replacement or repair only failed components of the transmission. An example illustrates the methods.

Savage, M.↗

A progress report on using bolometers cooled by adiabatic demagnetization refrigeration

For sensitive detection of astronomical continuum radiation in the 200 micron to 3 mm wavelength range, bolometers are presently the detectors of choice. In order to approach the limits imposed by photon noise in a cryogenically cooled telescope in space, bolometers must be operated at temperatures near 0.1 K. Researchers report progress in building and using bolometers that operate at these temperatures. The most sensitive bolometer had an estimated noise equivalent power (NEP) of 7 x 10(exp 017) W Hz(exp -1/2). Researchers also briefly discuss the durability of paramagnetic salts used to cool the bolometers.

Lesyna, L.↗

Transmission overhaul and replacement predictions using Weibull and renewal theory

A method to estimate the frequency of transmission overhauls is presented. This method is based on the two-parameter Weibull statistical distribution for component life. A second method is presented to estimate the number of replacement components needed to support the transmission overhaul pattern. The second method is based on renewal theory. Confidence statistics are applied with both methods to improve the statistical estimate of sample behavior. A transmission example is also presented to illustrate the use of the methods. Transmission overhaul frequency and component replacement calculations are included in the example.

Savage, M.↗

Tooth Contact Shift in Loaded Spiral Bevel Gears

An analytical method is presented to predict the shifts of the contact ellipses of spiral bevel gear teeth under load. The contact ellipse shift is the motion of the tooth contact position from the ideal pitch point to its location under load. The shifts are due to the elastic motions of the gear and pinion supporting shafts and bearings. The calculations include the elastic deflections of the gear shafts and the deflections of the four shaft bearings. The method assumes that the surface curvature of each tooth is constant near the unloaded pitch point. Results from these calculations will help designers reduce transmission weight without seriously reducing transmission performance.

Savage, M.↗

Vibration signature analysis of multistage gear transmission

An analysis is presented for multistage multimesh gear transmission systems. The analysis predicts the overall system dynamics and the transmissibility to the gear box or the enclosed structure. The modal synthesis approach of the analysis treats the uncoupled lateral/torsional model characteristics of each stage or component independently. The vibration signature analysis evaluates the global dynamics coupling in the system. The method synthesizes the interaction of each modal component or stage with the nonlinear gear mesh dynamics and the modal support geometry characteristics. The analysis simulates transient and steady state vibration events to determine the resulting torque variations, speeds, changes, rotor imbalances, and support gear box motion excitations. A vibration signature analysis examines the overall dynamic characteristics of the system, and the individual model component responses. The gear box vibration analysis also examines the spectral characteristics of the support system.

Choy, F. K.↗

Transmission overhaul and replacement predictions using Weibull and renewel theory

A method to estimate the frequency of transmission overhauls is presented. This method is based on the two-parameter Weibull statistical distribution for component life. A second method is presented to estimate the number of replacement components needed to support the transmission overhaul pattern. The second method is based on renewal theory. Confidence statistics are applied with both methods to improve the statistical estimate of sample behavior. A transmission example is also presented to illustrate the use of the methods. Transmission overhaul frequency and component replacement calculations are included in the example.

Savage, M.↗

Tooth contact shift in loaded spiral bevel gears

An analytical method is presented to predict the shifts of the contact ellipses of spiral bevel gear teeth under load. The contact ellipse shift is the motion of the tooth contact position from the ideal pitch point to its location under load. The shifts are due to the elastic motions of the gear and pinion supporting shafts and bearings. The calculations include the elastic deflections of the gear shafts and the deflections of the four shaft bearings. The method assumes that the surface curvature of each tooth is constant near the unloaded pitch point. Results from these calculations will help designers reduce transmission weight without seriously reducing transmission performance.

Savage, M.↗

Vibration signature analysis of multistage gear transmission

An analysis is presented for multistage multimesh gear transmission systems. The analysis predicts the overall system dynamics and the transmissibility to the gear box or the enclosed structure. The modal synthesis approach of the analysis treats the uncoupled lateral/torsional model characteristics of each stage or component independently. The vibration signature analysis evaluates the global dynamics coupling in the system. The method synthesizes the interaction of each modal component or stage with the nonlinear gear mesh dynamics and the modal support geometry characteristics. The analysis simulates transient and steady state vibration events to determine the resulting torque variations, speeds, changes, rotor imbalances, and support gear box motion excitations. A vibration signature analysis examines the overall dynamic characteristics of the system, and the individual model component responses. The gear box vibration analysis also examines the spectral characteristics of the support system.

Choy, F. K.↗

Computerized life and reliability modelling for turboprop transmissions

A generalized life and reliability model is presented for parallel shaft geared prop-fan and turboprop aircraft transmissions. The transmission life and reliability model is a combination of the individual reliability models for all the bearings and gears in the main load paths. The bearing and gear reliability models are based on classical fatigue theory and the two parameter Weibull failure distribution. A computer program was developed to calculate the transmission life and reliability. The program is modular. In its present form, the program can analyze five different transmission arrangements. However, the program can be modified easily to include additional transmission arrangements. An example is included which compares the life of a compound two-stage transmission with the life of a split-torque, parallel compound two-stage transmission as calculated by the comaputer program.

Savage, M.↗

Computing The Compliances Of Gear Meshes

Computer model simulates compliance and sharing of loads in spur-gear mesh. Use of solid-body analysis as lower bound and rim analysis as upper bound for mesh compliance, reasonable approximations obtained for compliance in spur-gear mesh.

Lewicki, D. G.↗

Computerized life and reliability modelling for turboprop transmissions

A generalized life and reliability model is presented for parallel shaft geared prop-fan and turboprop aircraft transmissions. The transmission life and reliability model is a combination of the individual reliability models for all the bearings and gears in the main load paths. The bearing and gear reliability models are based on classical fatigue theory and the two parameter Weibull failure distribution. A computer program was developed to calculate the transmission life and reliability. The program is modular. In its present form, the program can analyze five different transmission arrangements. However, the program can be modified easily to include additional transmission arrangements. An example is included which compares the life of a compound two-stage transmission with the life of a split-torque, parallel compound two-stage transmission, as calculated by the computer program.

Savage, M.↗

Flexibility effects on tooth contact location in spiral bevel gear transmissions

An analytical method to predict the shift of the contact ellipse between the meshing teeth in a spiral bevel gear set is presented in this report. The contact ellipse shift of interest is the motion of the nominal tooth contact location on each tooth from the ideal pitch point to the point of contact between the two teeth considering the elastic motions of the gears and their supporting shafts. This is the shift of the pitch point from the ideal, unloaded position on each tooth to the nominal contact location on the tooth when the gears are fully loaded. It is assumed that the major contributors of this motion are the elastic deflections of the gear shafts, the slopes of the shafts under load and the radial deflections of the four gear shaft bearings. The motions of the two pitch point locations on the pinion and the gear tooth surfaces are calculated in a FORTRAN program which also calculates the size and orientation of the Hertzian contact ellipse on the tooth faces. Based on the curvatures of the two spiral bevel gear teeth and the size of the contact ellipse, the program also predicts the basic dynamic capacity of the tooth pair. A complete numerical example is given to illustrate the use of the program.

Altidis, P. C.↗

Gear mesh compliance modeling

A computer model has been constructed to simulate the compliance and load sharing in a spur gear mesh. The model adds the effect of rim deflections to previously developed state-of-the-art gear tooth deflection models. The effects of deflections on mesh compliance and load sharing are examined. The model can treat gear meshes composed of two external gears or an external gear driving an internal gear. The model includes deflection contributions from the bending and shear in the teeth, the Hertzian contact deformations, and primary and secondary rotations of the gear rims. The model shows that rimmed gears increase mesh compliance and, in some cases, improve load sharing.

Savage, M.↗