Search NASA⌕ Search

Engineering topics

Saw, S H

Publications and source records attributed to Saw, S H.

Plasma focus ion beam fluence and flux-Scaling with stored energy

Measurements on plasma focus ion beams include various advanced techniques producing a variety of data which has yet to produce benchmark numbers [A Bernard et al., J. Mosc. Phys. Soc. 8, 93-170 (1998)]. This present paper uses the Lee Model code [S Lee, http://www.plasmafocus.net (2012)], integrated with experimental measurements to provide the basis for reference numbers and the scaling of deuteron beams versus stored energy E{sub 0}. The ion number fluence (ions m{sup -2}) and energy fluence (J m{sup -2}) computed as 2.4-7.8 Multiplication-Sign 10{sup 20} and 2.2-33 Multiplication-Sign 10{sup 6}, respectively, are found to be independent of E{sub 0} from 0.4 to 486 kJ. Typical inductance machines (33-55 nH) produce 1.2-2 Multiplication-Sign 10{sup 15} ions per kJ carrying 1.3%-4% E{sub 0} at mean ion energy 50-205 keV, dropping to 0.6 Multiplication-Sign 10{sup 15} ions per kJ carrying 0.7% E{sub 0} for the high inductance INTI PF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

In situ determination of the static inductance and resistance of a plasma focus capacitor bank

The static (unloaded) electrical parameters of a capacitor bank are of utmost importance for the purpose of modeling the system as a whole when the capacitor bank is discharged into its dynamic electromagnetic load. Using a physical short circuit across the electromagnetic load is usually technically difficult and is unnecessary. The discharge can be operated at the highest pressure permissible in order to minimize current sheet motion, thus simulating zero dynamic load, to enable bank parameters, static inductance L{sub 0}, and resistance r{sub 0} to be obtained using lightly damped sinusoid equations given the bank capacitance C{sub 0}. However, for a plasma focus, even at the highest permissible pressure it is found that there is significant residual motion, so that the assumption of a zero dynamic load introduces unacceptable errors into the determination of the circuit parameters. To overcome this problem, the Lee model code is used to fit the computed current trace to the measured current waveform. Hence the dynamics is incorporated into the solution and the capacitor bank parameters are computed using the Lee model code, and more accurate static bank parameters are obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Soft x-ray yield from NX2 plasma focus

The Lee model code is used to compute neon soft x-ray yield Y{sub sxr} for the NX2 plasma focus as a function of pressure. Comparison with measured Y{sub sxr} shows reasonable agreement in the Y{sub sxr} versus pressure curve, the absolute maximum yield as well as the optimum pressure. This gives confidence that the code gives a good representation of the neon plasma focus in terms of gross properties including speeds and trajectories and soft x-ray yields, despite its lack of modeling localized regions of higher densities and temperatures. Computed current curves versus pressure are presented and discussed particularly in terms of the dynamic resistance of the axial phase. Computed gross properties of the plasma focus including peak discharge current I{sub peak}, pinch current I{sub pinch}, minimum pinch radius r{sub min}, plasma density at the middle duration of pinch n{sub pinch}, and plasma temperature at middle duration of pinch T{sub pinch} are presented and the trends in variation of these are discussed to explain the peaking of Y{sub sxr} at optimum pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Response to 'Comment on 'Pinch current limitation effect in plasma focus'' [Appl. Phys. Lett. 94, 076101 (2009)]

The main point of the comment [Appl. Phys. Lett. 94, 076101 (2009)] is that Eq. (2) and consequentially Eq. (3) of the commented paper [Appl. Phys. Lett. 92, 021503 (2008)] require correction. The alternative equation suggested in the comment is derived using Kirchhoff's voltage rule. The comment consider only the energy distribution in the inductive components and the resultant equation confirms a progressive lowering of the I{sub pinch}/I{sub peak} ratio as the static inductance L{sub 0} is reduced, lowering from 0.87 to 0.31 as L{sub 0} is reduced from 100 to 5 nH according to the revised formula corresponding to Eq. (3), compared to 0.63-0.25 according to Eq. (3). This progressive lowering of the ratio I{sub pinch}/I{sub peak} due to the inductive energy distribution is one of two factors responsible for the pinch current limitation. The other factor is the progressive reduction in the L-C interaction time compared to the current dip duration denoted by {delta}{sub cap} in Eq. (2). The comment does not deal with {delta}{sub cap} at all; hence, its conclusion based on inductive energy distribution only is not useful, since in the low L{sub 0} region when pinch current limitation begins to manifest, {delta}{sub cap} becomes more and more the dominant factor. In any case, the results of the paper do not depend on Eqs. (2) and (3), which are used in the paper only for illustrative purposes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Computing plasma focus pinch current from total current measurement

The total current I{sub total} waveform in a plasma focus discharge is the most commonly measured quantity, contrasting with the difficult measurement of I{sub pinch}. However, yield laws should be scaled to focus pinch current I{sub pinch} rather than the peak I{sub total}. This paper describes how I{sub pinch} may be computed from the I{sub total} trace by fitting a computed current trace to the measured current trace using the Lee model. The method is applied to an experiment in which both the I{sub total} trace and the plasma sheath current trace were measured. The result shows good agreement between the values of computed and measured I{sub pinch}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗