Search NASA⌕ Search

Engineering topics

Scallion, W. I.

Publications and source records attributed to Scallion, W. I..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Performance of an aerodynamic yaw controller mounted on the space shuttle orbiter body flap at Mach 10

A wind-tunnel investigation of the effectiveness of an aerodynamic yaw controller mounted on the lower surface of a shuttle orbiter model body flap was conducted in the Langley 31-Inch Mach 10 Tunnel. The controller consisted of a 60 deg delta fin mounted perpendicular to the body flap lower surface and yawed 30 deg to the free stream direction. The control was tested at angles of attack from 20 deg to 40 deg at zero sideslip for a Reynolds number based on wing mean aerodynamic chord of 0.66 x 10(exp 6). The aerodynamic and control effectiveness characteristics are presented along with an analysis of the effectiveness of the controller in making a bank maneuver for Mach 18 flight conditions. The controller was effective in yaw and produced a favorable rolling moment. The analysis showed that the controller was as effective as the reaction control system in making the bank maneuver. These results warrant further studies of the aerodynamic/aerothermodynamic characteristics of the control concept for application to future transportation vehicles.

Scallion, W. I.↗
NASA NTRS1991

An advanced hypervelocity aerophysics facility - A ground-based flight-test range

The paper discusses a concept for a ground-based flight-test facility, a large aeroballistic range capable of launching models large enough to permit the installation of significant amounts of onboard instrumentation. The large model size would also provide thick shock/boundary layers, thus providing the opportunity to measure flow-field properties via advanced offboard diagnostics. Current fabrication technology should permit the construction of a two-stage light-gas gun capable of accelerating 20 to 25 cm diameter models to velocities on the order of 6 km/sec. An electromagnetic launcher or a ram accelerator is considered as a potential means for achieving larger model sizes and/or greater launch velocities. Possible methods for obtaining and recording data are discussed as are the test chamber and model deceleration section requirements.

Witcofski, R. D.↗
NASA NTRS1986

Bailout from the Space Shuttle

Studies to investigate the bailout characteristics from the Space Shuttle Orbiter at low-subsonic speeds have been made in the Langley 12-foot Low-Speed Tunnel and the Langley 4- by 7Meter Tunnel with 0.03-scale models. The effect of crew-model exit velocity, body posture, and body weight were studied with egress from the Orbiter main side hatch and from the upper cabin hatch. Force tests were made to determine the high angle-of-attack trim characteristics of the Orbiter in an attempt to improve bailout conditions. A computer simulation was made to evaluate the maneuver necessary to attain the high-angle trim.

Ware, G. M.↗
NASA NTRS1985

Space Shuttle orbiter trimmed center-of-gravity extension study

Aerodynamic, heat transfer, and system design studies to determine removable modifications for the Space Shuttle orbiter that would extend its forward center-of-gravity triom capability are summarized. Wind-tunnel tests were conducted at Mach numbers ranging from 0.25 to 20.3 to determine the most effective aerodynamic modifications. Heat transfer and system design studies determined the impact of the modifications on the thermal protection system and structural weight of the vehicle. The most effective modifications were in-fillet canards or a forward extension of the existing forward wing fillet.

Scallion, W. I.↗
NASA NTRS1985

Study of several factors affecting crew escape trajectories from the Space Shuttle Orbiter at low-subsonic speeds

Factors affecting the bailout characteristics from the space shuttle orbiter at low-subsonic speeds were investigated. In the 12-foot low-speed tunnel and the 4 by 7-meter tunnel with 0.03-scale models. The effect of crew-model exit velocity, body position, and body weight were studied with egress from the main side hatch with the orbiter upright and from the upper cabin hatch with the orbiter inverted. Crew model drag and flow field measurements around the orbiter were estimated. The high-angle-of-attack trim characteristics of the orbiter was determined by force tests in an attempt to improve bailout conditions. A computer simulation was made to evaluate the maneuver necessary to attain the high-angle-of-attack trim.

Scallion, W. I.↗
NASA NTRS1985

The aerodynamic challenges of the design and development of the space shuttle orbiter

The major aerodynamic design challenge at the beginning of the United States Space Transportation System (STS) research and development phase was to design a vehicle that would fly as a spacecraft during early entry and as an aircraft during the final phase of entry. The design was further complicated because the envisioned vehicle was statically unstable during a portion of the aircraft mode of operation. The second challenge was the development of preflight aerodynamic predictions with an accuracy consistent with conducting a manned flight on the initial orbital flight. A brief history of the early contractual studies is presented highlighting the technical results and management decisions influencing the aerodynamic challenges. The configuration evolution and the development of preflight aerodynamic predictions will be reviewed. The results from the first four test flights shows excellent agreement with the preflight aerodynamic predictions over the majority of the flight regimes. The only regimes showing significant disagreement is confined primarily to early entry, where prediction of the basic vehicle trim and the influence of the reaction control system jets on the flow field were found to be deficient. Postflight results are analyzed to explain these prediction deficiencies.

Young, J. C.↗
NASA NTRS1984

Investigation of the effect of vehicle, angle-of-attack, and trim elevon position on lateral-directional aerodynamic parameters of the Shuttle Orbiter

This paper discusses the lateral-directional stability and control coefficients extracted from onboard measurements made during reentry of flights two to eight of the Space Shuttle Orbiters. Maximum likelihood estimation is applied to data derived from accelerometer and rate gyro measurements and trajectory, meteorological and control surface data to estimate these lateral-directional parameters. Comparison of estimated coefficients across the seven flights and two shuttle vehicles is made. The effect of the angle-of-attack, and trim elevon deflection on estimated values of the stability and control derivatives is also studied.

Schiess, J. R.↗
NASA NTRS1983

Analysis of shuttle oscillation in the Mach Number = 1.7 to Mach Number = 1.0 range

The first five flights of the Space Transportation System (STS) have exhibited unexpected lateral oscillations in the Mach Number = 1.7 to Mach Number = 1.0 region of the descent trajectory. These oscillations can be split into two parts: a predominantly rolling oscillation referred to as the quarter hertz motion and a long-priod, large-amplitude oscillation in sideslips, roll rate, and yaw rate. These motions are analyzed in this paper in order to determine their source and the mechanism driving them. They will first be examined to determine how much of the motion can be explained using the set of equations that contain linear aerodynamic parameters. Then differences between measured moments and those calculated using linear aerodynamics which are considered to be due to unmodeled moments will be exained. Possible error sources such as not inluding nonlinear aerodynamics in the vehicle model, measurement errors, and the effect of pressure gradients will be considered. Based on these analyses, conclusions as to the nature and cause of the Shuttle lateral oscillations will be drawn.

Suit, W. T.↗
NASA NTRS1983

Stability and control over the supersonic and hypersonic speed range

The performance and aerodynamic characteristics of the Space Shuttle Columbia are analyzed over the speed range from Mach 2 to 26 using flight data taken from the first five Space Transportation System flights. These data are used to reconstruct the entry trajectory, calculate vehicle performance, and estimate lateral stability and control derivatives including those assocated with the onboard Reaction Control System. The trajectory reconstruction process is discussed in its relationship to the determination of the vehicle flight characteristics. Vehicle performance results are presented which show that lift and drag were generally overpredicted by 3 percent and that the life-to-drag ratio was underpredicted by 1 percent. Anomalies in pitching-moment trim characteristics are shown and noted to be due to real-gas and Mach-number effects. Lateral stability and control derivatives estimated using programmed test input maneuvers are corrected with preflight predictions and are usually within the uncertainties associated with the predictions. The lateral reaction-control system effectiveness is evaluated.

Compton, H. R.↗
NASA NTRS1983

Space Shuttle third flight /STS-3/ entry RCS analysis

Flight data obtained from three Space Transportation System orbiter entries (STS-1, 2, and 3) are processed and analyzed to determine the roll interactions caused by the firing of the entry reaction control system (RCS). Comparisons between the flight-derived parameters and the predicted derivatives without interaction effects are made. The flight-derived RCS Plume flow-field interaction effects are independently deduced by direct integration of the incremental changes in the wing upper surface pressures induced by RCS side thruster firings. The separately obtained interaction effects are compared to the predicted values and the differences are discussed.

Scallion, W. I.↗
NASA NTRS1983

Simplified analysis techniques to support the determination of Shuttle aerodynamics

The use of deterministic and regression methods to supplement the maximum likelihood estimation programs for the determination of the stability and control parameters of the Shuttle vehicle is discussed. Examples taken from STS-2 and STS-3 flight data show the use of deterministic methods to verify the effectiveness of the pitch and roll Reaction Control System (RCS), to verify the model structure used in the maximum likelihood estimator and to indicate regions of the descent trajectory where unmodeled moments dominate the vehicle motion and the application of maximum likelihood estimation would lead to incorrect parameter values. The use of regression methods to determine selected parameters when the more sophisticated maximum likelihood programs are not required, to determine the form of the vehicle mathematical model and to select the data time intervals for most effective parameter identification are also discussed.

Suit, W. T.↗
NASA NTRS1982

Shuttle entry performance and stability and control derivatives extraction from flight measurement data

Flight data taken from three Shuttle Space Transportation System flights (STS-1, 2, and 3) during entry are analyzed to determine the shuttle performance and aerodynamic characteristics. Correlations of the performance coefficients and the stability and control derivatives with preflight predictions are presented over the hypersonic speed range from Mach 2 to 25. In addition, an evaluation of the effectiveness of the onboard Reaction Control System (RCS) is given and an effort is made to independently quantify the combined impingement and flow-field interaction effects on the spacecraft rolling moment. Comparisons of stability and control derivatives extracted for the same flight conditions, but using data from different onboard sensors are also made. Results obtained using the same flight data, but different computer software are also shown.

Compton, H. R.↗
NASA NTRS1982

Space-vehicle correlation of ground and flight experiments

A 2-percent-scale model was designed for testing in the NTF. This model has remotely controlled elevons, body flap, and rudder to minimize tunnel entries associated with configuration changes in the NTF. The Shuttle Orbiter has a very large aerodynamic data base obtained in ground facilities. Since the vehicle flight-test program has already begun, a large amount of flight data can be analyzed and correlated with the NTF results.

Scallion, W. I.↗
NASA NTRS1978

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 4: Effects of configuration modifications on the aerodynamic characteristics of the 139B orbiter at Mach 20.3

Force tests were conducted at Mach 20.3 to determine the effect of several forebody, wing-fillet, and canard modifications on the hypersonic trim capability of a 139B Space Shuttle Orbiter model. Force and moment data were obtained at angles of attack of 10 deg to 54 deg at zero sideslip angle and at a Reynolds number of 1,900,000 based on body length. The results indicated that wing-fillet and canard modifications would increase the allowable forward trimmed center-of-gravity capability by as much as 3.0 percent of the body length.

Scallion, W. I.↗
NASA NTRS1972

Status of Langley studies of aerodynamics and interference effects of tandem launch vehicles

Some of the aerodynamic and interference effects measured from wind-tunnel tests of three fully reusable space shuttle configurations at transonic and low-supersonic speeds are presented, and the status is given of an assessment of the analytical approach to date. The three configurations tested were a low-fineness-ratio booster combined in tandem with a delta-wing orbiter, designated the "low-fineness-ratio configuration,' and a phase B shuttle configuration consisting of the delta-wing orbiter and high-fineness-ratio booster, designated the "stage-arrangement configuration,' arranged in tandem and in parallel. The force measurements obtained at a Mach number of 1.5 for the low-fineness-ratio configuration were representative of the transonic and low-supersonic speed ranges where the interference effects are predominant and were used for comparison with values calculated at the same Mach number. This comparison is the basis for a preliminary assessment of the initial application of the analytical approach.

Scallion, W. I.↗