Search NASA⌕ Search

Engineering topics

Scannapieco, Anthony J.

Publications and source records attributed to Scannapieco, Anthony J..

Derivation of a Multi-Species Mix Model

Multi-species flow takes place when two or more gases, plasmas or fluids are flowing and interacting with one another through particle collisions, chemical reactions, turbulence, and thermonuclear processes; this list is not exhaustive. It has a wide range of applications in geological, biological and engineering systems. In what follows species refers to different species of atoms or molecules that may or may not be partially or fully ionized. The interactions between these species takes place at an atomic or molecular level. The species are electrically neutral. These are very important points, because the coupling between species that are interacting on a mesoscale level or are immiscible would be very different than what is being considered in this work. In addition, in section 4, we present a heuristic argument to enhance the collisional mean free path to incorporate the effects of turbulent eddies by use of Prandtl’s assumption that the integral scale length of a turbulent boundary layer is proportional to the width of the turbulent layer. This leads to coupling terms that are non-Newtonian, because they are a function of the dynamics of the flow. It is also assumed that the turbulent stress terms are much smaller than the species partial pressures. This may be a good assumption if the species are hot, dense plasmas that exist in ICF targets.

74 ATOMIC AND MOLECULAR PHYSICS↗

Parallel Implicit Hydrodynamics with Material Strength for High Explosive Burn Calculations

High explosives are almost always evolving in some form of metal containment vessel. This fact requires that a materials model for the evolution of the metal containment vessel be part of any simulation of the HE. Since the actual form of the strength model to be used is an open question, we incorporate the material strength properties in a relatively agnostic fashion, which will accommodate many strength models. The only restriction is that the stress components be a function of density, specific internal energy and velocities. In addition, the timescales and rates of the chemical reactions in the HE vary between thousands of seconds and nanoseconds. A hydrodynamics capable of operating in anticipation of the eventual violent release of energy via these chemical reactions is a necessity. The central issue in creating a hydrodynamics capable of spanning these timescales is to forgo the use of a Courant time step control necessary in an explicit hydrodynamics. The Courant time-step arises because of characteristic velocities associated with the material, such as the sound speed or, in materials with strength, characteristic longitudinal and transverse speeds associated with compression and shear. The method used to circumvent the need for a Courant time-step limit is to develop an implicit calculation of the advanced particle pressure and shear modulus derived from the conservation laws of mass, momentum and specific internal energy. This process creates the implicit hydrodynamics needed for the HE calculations of interest to this study.

36 MATERIALS SCIENCE↗

Role of heating and turbulent heat transfer in HE burning and detonation

Enhanced heat transfer model has been developed due to the turbulence in the cracks and pores in the burning fractured HE. This turbulence then serves in the initialization of the turbulence in the product gas. Enhanced heat transfer is also modeled in the turbulent product gas. Numerical simulations of the onset of HE burning and transition to detonation have been performed with and without the turbulent heat transfer model. Computational results indicate that onset of chemical reactions and transition to detonation is induced by the shockwave formed by the pressure rise caused by the heating. In other words, processes similar to shock-to-detonation transition (SDT) could become the driving mechanism for HE explosion and detonation in the case of heating rather than the temperature alone.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Simulation of flame acceleration and deflagration-to-detonation transition with heat transfer in HE product and fractured HE

A simple heat transfer model has been developed for high explosives. For the gaseous high explosive (HE) product, the Smargorinsky eddy viscosity model has been adopted for estimating the turbulent thermal conductivity. Convective heat transfer in the fractured solid HE is modeled as the effective thermal conduction in the porous media, which is equivalent to the enthalpy flux carried by the velocity determined by Darcy’s law with Forchheimer term.Other features of the model include a multi-reaction chain, equation-of-state for each species involved, and a two-phase hotspot model. Test calculations are performed with various initial disturbances. Onset and progress of flame acceleration (FA) and chemical reactions are strongly affected by the heat transfer and initial disturbance. Staged development of FA also affirms the necessity of modeling based on a multi-reaction chain. When conditions warrant,e.g., stronger initial disturbance, FA evolves to deflagration-to-detonation transition (DDT),demonstrating automatic capture of the DDT.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Multiphase representation of hotspot formation and growth

Multiphase reacting flow approach has been adopted for modeling of hotspot formation and growth on sub-zonal scale. Mechanical response of the high explosive (HE) is modeled by the Visco-Plastic SCRAM model which includes plastic work, crack growth, and frictional heating along the cracks. In this work a sub-zonal regions with high temperature, hotspots, are modeled as a new phase. Formation and growth of the hotspot phase from the cold phase is modeled as a phase change. Each phase has its own temperature and pressure. Chemical reactions also progress in both phases. The growth of hotspots are determined by the solution of the heat conduction equation with appropriate heat sources due to friction and plastic heating. Sample calculations using the BABBO code show successful detonation calculations with hotspot formation and growth.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Notes on Eulerian Magnetohydrodynamics

A brief description of the MHD equations used in the eulerian AMR code BABBO is presented. The description of the MHD equations has been presented many times in the literature so only a very brief description is given in this report. Of particular importance is the description of the calculation of the plasma load impedance and inductance, which is much less frequently described in the literature and is presented in section 6. In addition, along with an accurate calculation of the plasma load impedance and induction, the circuit calculation used to introduce the external current drive is of particular importance and is presented in section 7. In section 8 a procedure is presented to calculate the current drive of a Marx bank by reverse engineering a machine voltage source, which can then be used to drive varying plasma loads.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

HMX detonation calculation using multi-reaction chain

Detonation of HMX has been simulated using a multi-reaction chain and species equation-of-states. A reacting flow code capable of handling arbitrary number of reactions and species has been used. Computational results are compared to the results produced by a pressure-based single reaction model (AJEX) and a temperature-based single-reaction model. Results show that the multi-reaction approach is capable of producing detonation calculations comparable to the AJEX model calculations, demonstrating that the multi-reaction approach possesses the properties required for the detonation modeling, a prerequisite of deflagration-to-detonation transition modeling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Parallel Implicit Hydrodynamics for High Explosive Burn Calculations

High explosives in hostile environments will require calculational capabilities that model processes, which evolve on timescales from minutes to nanoseconds. Eventually the HE will begin to move metal. To handle this temporal evolution an implicit hydrodynamics coupled to the chemical release of the HE energy is required. In addition, the use of chemical kinetics to model the transition from, the initially, slow heating of a confined high explosive through to deflagration and on to detonation requires many computational zones to model high explosive engineering systems. This requirement means that a fully parallel implicit hydrodynamics is essential. In this paper we present the calculation of a nonlinear matrix equation for the advanced particle pressure that has been made parallel and implemented in our AMR code, BABBO. This new parallel implicit hydrodynamics has been applied to a cookoff problem, as well as, one and two dimensional shock problems. Results are presented and discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Resistive MHD calculations with ROXANE

We discuss the efficacy of the adaptive mesh refinement (AMR) code ROXANE in performing resistive Magnetohydrodynamic (MHD) simulations. Two-dimensional simulations with ROXANE for a generic Z-pinch setup for imploding a cylindrical liner shows that random hotspots known to occur in other codes in the insulator region are absent here. Furthermore, artificial instabilities present in other codes due to mesh imprinting are not present in ROXANE. The fundamental reasons for the better performance of ROXANE in resistive MHD simulations is the interface treatment in a cell containing two conductors (materials), avoiding the artificial mixing of disparate resistivities.

36 MATERIALS SCIENCE↗

An Adaptive Mesh Algorithm: Mapping the Mesh Variables

Both thermodynamic and kinematic variables must be mapped. The kinematic variables are defined on a separate kinematic mesh; it is the duel mesh to the thermodynamic mesh. The map of the kinematic variables is done by calculating the contributions of kinematic variables on the old thermodynamic mesh, mapping the kinematic variable contributions onto the new thermodynamic mesh and then synthesizing the mapped kinematic variables on the new kinematic mesh. In this document the map of the thermodynamic variables will be described.

97 MATHEMATICS AND COMPUTING↗

Equation-of-State Scaling Factors

Equation-of-State scaling factors are needed when using a tabular EOS in which the user de ned material isotopic fractions di er from the actual isotopic fractions used by the table. Additionally, if a material is dynamically changing its isotopic structure, then an EOS scaling will again be needed, and will vary in time and location. The procedure that allows use of a table to obtain information about a similar material with average atomic mass Ms and average atomic number Zs is described below. The procedure is exact for a fully ionized ideal gas. However, if the atomic number is replace by the e ective ionization state the procedure can be applied to partially ionized material as well, which extends the applicability of the scaling approximation continuously from low to high temperatures.

97 MATHEMATICS AND COMPUTING↗

An Adaptive Mesh Algorithm: Mesh Structure and Generation

The purpose of Adaptive Mesh Refinement is to minimize spatial errors over the computational space not to minimize the number of computational elements. The additional result of the technique is that it may reduce the number of computational elements needed to retain a given level of spatial accuracy. Adaptive mesh refinement is a computational technique used to dynamically select, over a region of space, a set of computational elements designed to minimize spatial error in the computational model of a physical process. The fundamental idea is to increase the mesh resolution in regions where the physical variables are represented by a broad spectrum of modes in k-space, hence increasing the effective global spectral coverage of those physical variables. In addition, the selection of the spatially distributed elements is done dynamically by cyclically adjusting the mesh to follow the spectral evolution of the system. Over the years three types of AMR schemes have evolved; block, patch and locally refined AMR. In block and patch AMR logical blocks of various grid sizes are overlaid to span the physical space of interest, whereas in locally refined AMR no logical blocks are employed but locally nested mesh levels are used to span the physical space. The distinction between block and patch AMR is that in block AMR the original blocks refine and coarsen entirely in time, whereas in patch AMR the patches change location and zone size with time. The type of AMR described herein is a locally refi ned AMR. In the algorithm described, at any point in physical space only one zone exists at whatever level of mesh that is appropriate for that physical location. The dynamic creation of a locally refi ned computational mesh is made practical by a judicious selection of mesh rules. With these rules the mesh is evolved via a mesh potential designed to concentrate the nest mesh in regions where the physics is modally dense, and coarsen zones in regions where the physics is modally sparse.

97 MATHEMATICS AND COMPUTING↗

Interface- and discontinuity-aware numerical schemes for plasma 3-T radiation diffusion in two and three dimensions

A set of numerical schemes is developed for two- and three-dimensional time-dependent 3-T radiation diffusion equations in systems involving multi-materials. To resolve sub-cell structure, interface reconstruction is implemented within any cell that has more than one material. Therefore, the system of 3-T radiation diffusion equations is solved on two- and three-dimensional polyhedral meshes. The focus of the development is on the fully coupling between radiation and material, the treatment of nonlinearity in the equations, i.e., in the diffusion terms and source terms, treatment of the discontinuity across cell interfaces in material properties, the formulations for both transient and steady states, the property for large time steps, and second order accuracy in both space and time. The discontinuity of material properties between different materials is correctly treated based on the governing physics principle for general polyhedral meshes and full nonlinearity. The treatment is exact for arbitrarily strong discontinuity. The scheme is fully nonlinear for the full nonlinearity in the 3-T diffusion equations. Three temperatures are fully coupled and are updated simultaneously. The scheme is general in two and three dimensions on general polyhedral meshes. The features of the scheme are demonstrated through numerical examples for transient problems and steady states. The effects of some simplifications of numerical schemes are also shown through numerical examples, such as linearization, simple average of diffusion coefficient, and approximate treatment for the coupling between radiation and material.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Second-order accurate interface- and discontinuity-aware diffusion solvers in two and three dimensions

A numerical scheme is developed for two- and three-dimensional time-dependent diffusion equations in numerical simulations involving mixed cells. The focus of the development is on the formulations for both transient and steady states, the property for large time steps, second-order accuracy in both space and time, the correct treatment of the discontinuity in material properties, and the handling of mixed cells. For a mixed cell, interfaces between materials are reconstructed within the cell so that each of resulting sub-cells contains only one material and the material properties of each sub-cell are known. Diffusion equations are solved on the resulting polyhedral mesh even if the original mesh is structured. The discontinuity of material properties between different materials is correctly treated based on governing physics principles. The treatment is exact for arbitrarily strong discontinuity. The formulae for effective diffusion coefficients across interfaces between materials are derived for general polyhedral meshes. The scheme is general in two and three dimensions. Since the scheme to be developed in this paper is intended for multi-physics code with adaptive mesh refinement (AMR), we present the scheme on mesh generated from AMR. The correctness and features of the scheme are demonstrated for transient problems and steady states in one-, two-, and three-dimensional simulations for heat conduction and radiation heat transfer. The test problems involve dramatically different materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗