Search NASA⌕ Search

Engineering topics

Scheffe, Jonathan R.

Publications and source records attributed to Scheffe, Jonathan R..

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Solar Thermochemical Redox Cycling Using Ga- and Al-Doped LSM Perovskites for Renewable Hydrogen Production

Solar thermochemical hydrogen production using redox-active metal oxides is a promising pathway for the production of green hydrogen and synthetic fuel precursors. Herein, the perovskite material (La 0.6 Sr 0.4 ) 0.95 Mn 0.8 Ga 0.2 O 3–δ (LSMG6482) is identified as a promising metal oxide for thermochemical water splitting. LSMG6482, along with more-established water splitters ceria and (La 0.6 Sr 0.4 ) 0.95 Mn x Al 1–x O 3–δ (LSMA) perovskites, is experimentally characterized via thermogravimetric (TGA) analysis and high-temperature water splitting in a reactor simulating solar concentrating conditions. TGA analysis demonstrated that LSMG6482 has high and stable oxygen exchange capacity under controlled pO 2 redox cycling, demonstrated by large changes in oxygen nonstoichiometry (δ) relative to ceria. Water splitting experiments using laser heating (T red = 1400 °C, T ox = 1200 °C) resulted in H 2 yields of 165.1 μmol g –1 for the candidate LSMG6482 composition, exceeding that of all benchmark materials tested. Under high conversion oxidation conditions, where H 2 is cointroduced with H 2 O (150 ≤ nH 2 O/nH 2 ≤ 500), H 2 yields were greatest for LSMG6482 and LSMA6482, up to four times that of ceria at the highest nH 2 O/nH 2 conditions. Crystallographic analysis showed that over the course of experimentation, there is some secondary phase growth for all perovskite compositions, except for LSMA6482, but there was no observable degradation in H 2 yields.

08 HYDROGEN↗
DOE OSTI2023

LaMnO 3 Dopants for Efficient Thermochemical Water Splitting Identified by Density Functional Theory Calculations

While ceria is the standard material for two-step water splitting, perovskites are emerging as viable alternatives. In this work, based on the orthorhombic LaMnO 3 supercell, we substitute Li Na K Rb Mg Ca Sr Ba on the A-sites (La sites) and Al Ga In Mg Zn on the B-sites (Mn sites) at a concentration of 37.5%. The range of temperature and oxygen partial pressure at which each composition is stable is predicted. For compositions that are stable in relevant temperature and pressure ranges, the oxygen vacancy formation energies are determined for all of the oxygen vacancy site positions available in the computational supercell. Mg, Ca, Sr, and Ba A-site-substituted LaMnO 3 and Al and In B-site-substituted LaMnO 3 meet these two criteria for candidates in solar-thermal water splitting applications. Finally, oxygen vacancy formation energy can also be controlled by adjusting the doping strategy.

08 HYDROGEN↗
DOE OSTI2023

Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites

Synthesis of solar thermochemical hydrogen (STCH) production redox materials with engineered structures, for example, replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of lanthanum strontium manganese (LSM)-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La 0.65 Sr 0.35 MnO 3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO 2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H 2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C and 1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Here, foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled-up STCH systems.

08 HYDROGEN↗