Engineering topics

Schmit, Paul F.

Publications and source records attributed to Schmit, Paul F..

10 records

DOE OSTI2022

Estimation of stagnation performance metrics in magnetized liner inertial fusion experiments using Bayesian data assimilation

Here we present a new analysis methodology that allows for the self-consistent integration of multiple diagnostics including nuclear measurements, x-ray imaging, and x-ray power detectors to determine the primary stagnation parameters, such as temperature, pressure, stagnation volume, and mix fraction in magnetized liner inertial fusion (MagLIF) experiments. The analysis uses a simplified model of the stagnation plasma in conjunction with a Bayesian inference framework to determine the most probable configuration that describes the experimental observations while simultaneously revealing the principal uncertainties in the analysis. We validate the approach by using a range of tests including analytic and three-dimensional MHD models. An ensemble of MagLIF experiments is analyzed, and the generalized Lawson criterion χ is estimated for all experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Deep-learning-enabled Bayesian inference of fuel magnetization in magnetized liner inertial fusion

Fuel magnetization in magneto-inertial fusion (MIF) experiments improves charged burn product confinement, reducing requirements on fuel areal density and pressure to achieve self-heating. By elongating the path length of 1.01 MeV tritons produced in a pure deuterium fusion plasma, magnetization enhances the probability for deuterium–tritium reactions producing 11.8-17.1 MeV neutrons. Nuclear diagnostics thus enable a sensitive probe of magnetization. Characterization of magnetization, including uncertainty quantification, is crucial for understanding the physics governing target performance in MIF platforms, such as magnetized liner inertial fusion (MagLIF) experiments conducted at Sandia National Laboratories, Z-facility. We demonstrate a deep-learned surrogate of a physics-based model of nuclear measurements. A single model evaluation is reduced from O ( 10 – 100 ) (10–100) CPU hours on a high-performance computing cluster down to O ( 10 – 100 ) (10) ms on a laptop. This enables a Bayesian inference of magnetization, rigorously accounting for uncertainties from surrogate modeling and noisy nuclear measurements. The approach is validated by testing on synthetic data and comparing with a previous study. We analyze a series of MagLIF experiments systematically varying preheat, resulting in the first ever systematic experimental study of magnetic confinement properties of the fuel plasma as a function of fundamental inputs on any neutron-producing MIF platform. We demonstrate that magnetization decreases from B R ∼ 0.2 ~0.5 to B R ∼ 0.2 ~0.2 MG cm as laser preheat energy deposited increases from E preheat ∼ 460 ~460 J to E preheat ∼ 460 ~1.4 kJ. This trend is consistent with 2D LASNEX simulations showing Nernst advection of the magnetic field out of the hot fuel and diffusion into the target liner.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2019

Design of dynamic screw pinch experiments for magnetized liner inertial fusion

Magnetic implosion of cylindrical metallic shells (liners) is an effective method for compressing preheated, premagnetized fusion fuel to thermonuclear conditions [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] but suffers from magneto-Rayleigh–Taylor instabilities (MRTI) that limit the attainable fuel pressure, density, and temperature. A novel method proposed by Schmit et al. [Phys. Rev. Lett. 117, 205001 (2016)] uses a helical magnetic drive field with a dynamic polarization at the outer surface of the liner during implosion, reducing (linear) MRTI growth by one to two orders of magnitude via a solid liner dynamic screw pinch (SLDSP) effect. This report investigates the design features necessary for successful experimental implementation of this concept. Whereas typical experiments employ purely azimuthal drive fields to implode initially solid liners, SLDSP experiments establish a helical drive field at the liner outer surface, resulting in enhanced average magnetic pressure per unit drive current, mild spatial nonuniformities in the magnetic drive pressure, and augmented static initial inductance in the pulsed-power drive circuit. Each of these topics has been addressed using transient magnetic and magnetohydrodynamic simulations; the results have led to a credible design space for SLDSP experiments on the Z Facility. We qualitatively assess the stabilizing effects of the SLDSP mechanism by comparing MRTI growth in a liner implosion simulation driven by an azimuthal magnetic field vs one driven with a helical magnetic field; the findings imply an apparent reduction in MRTI growth when a helical drive field is employed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2016

Exploring magnetized liner inertial fusion with a semi-analytic model

In this paper, we explore magnetized liner inertial fusion (MagLIF) [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)] using a semi-analytic model [R. D. McBride and S. A. Slutz, Phys. Plasmas 22, 052708 (2015)]. Specifically, we present simulation results from this model that: (a) illustrate the parameter space, energetics, and overall system efficiencies of MagLIF; (b) demonstrate the dependence of radiative loss rates on the radial fraction of the fuel that is preheated; (c) explore some of the recent experimental results of the MagLIF program at Sandia National Laboratories [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)]; (d) highlight the experimental challenges presently facing the MagLIF program; and (e) demonstrate how increases to the preheat energy, fuel density, axial magnetic field, and drive current could affect future MagLIF performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2015

Implementing and diagnosing magnetic flux compression on the Z pulsed power accelerator

We report on the progress made to date for a Laboratory Directed Research and Development (LDRD) project aimed at diagnosing magnetic flux compression on the Z pulsed-power accelerator (0-20 MA in 100 ns). Each experiment consisted of an initially solid Be or Al liner (cylindrical tube), which was imploded using the Z accelerator's drive current (0-20 MA in 100 ns). The imploding liner compresses a 10-T axial seed field, B z ( 0 ) , supplied by an independently driven Helmholtz coil pair. Assuming perfect flux conservation, the axial field amplification should be well described by B z ( t ) = B z ( 0 ) x [ R ( 0 ) / R ( t )] 2 , where R is the liner's inner surface radius. With perfect flux conservation, B z ( t ) and dB z / dt values exceeding 10 4 T and 10 12 T/s, respectively, are expected. These large values, the diminishing liner volume, and the harsh environment on Z, make it particularly challenging to measure these fields. We report on our latest efforts to do so using three primary techniques: (1) micro B-dot probes to measure the fringe fields associated with flux compression, (2) streaked visible Zeeman absorption spectroscopy, and (3) fiber-based Faraday rotation. We also mention two new techniques that make use of the neutron diagnostics suite on Z. These techniques were not developed under this LDRD, but they could influence how we prioritize our efforts to diagnose magnetic flux compression on Z in the future. The first technique is based on the yield ratio of secondary DT to primary DD reactions. The second technique makes use of the secondary DT neutron time-of-flight energy spectra. Both of these techniques have been used successfully to infer the degree of magnetization at stagnation in fully integrated Magnetized Liner Inertial Fusion (MagLIF) experiments on Z [P. F. Schmit et al. , Phys. Rev. Lett. 113 , 155004 (2014); P. F. Knapp et al. , Phys. Plasmas, 22 , 056312 (2015)]. Finally, we present some recent developments for designing and fabricating novel micro B-dot probes to measure B z ( t ) inside of an imploding liner. In one approach, the micro B-dot loops were fabricated on a printed circuit board (PCB). The PCB was then soldered to off-the-shelf 0.020- inch-diameter semi-rigid coaxial cables, which were terminated with standard SMA connectors. These probes were recently tested using the COBRA pulsed power generator (0-1 MA in 100 ns) at Cornell University. In another approach, we are planning to use new multi-material 3D printing capabilities to fabricate novel micro B-dot packages. In the near future, we plan to 3D print these probes and then test them on the COBRA generator. With successful operation demonstrated at 1-MA, we will then make plans to use these probes on a 20-MA Z experiment.

47 OTHER INSTRUMENTATION↗

DOE OSTI2015

Demonstration of thermonuclear conditions in magnetized liner inertial fusion experiments

The magnetized liner inertial fusion concept [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)] utilizes a magnetic field and laser heating to relax the pressure requirements of inertial confinement fusion. The first experiments to test the concept [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] were conducted utilizing the 19 MA, 100 ns Z machine, the 2.5 kJ, 1 TW Z Beamlet laser, and the 10 T Applied B-field on Z system. Despite an estimated implosion velocity of only 70 km/s in these experiments, electron and ion temperatures at stagnation were as high as 3 keV, and thermonuclear deuterium-deuterium neutron yields up to 2 × 10{sup 12} have been produced. X-ray emission from the fuel at stagnation had widths ranging from 50 to 110 μm over a roughly 80% of the axial extent of the target (6–8 mm) and lasted approximately 2 ns. X-ray yields from these experiments are consistent with a stagnation density of the hot fuel equal to 0.2–0.4 g/cm{sup 3}. In these experiments, up to 5 × 10{sup 10} secondary deuterium-tritium neutrons were produced. Given that the areal density of the plasma was approximately 1–2 mg/cm{sup 2}, this indicates the stagnation plasma was significantly magnetized, which is consistent with the anisotropy observed in the deuterium-tritium neutron spectra. Control experiments where the laser and/or magnetic field were not utilized failed to produce stagnation temperatures greater than 1 keV and primary deuterium-deuterium yields greater than 10{sup 10}. An additional control experiment where the fuel contained a sufficient dopant fraction to substantially increase radiative losses also failed to produce a relevant stagnation temperature. The results of these experiments are consistent with a thermonuclear neutron source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2015

Effects of magnetization on fusion product trapping and secondary neutron spectra

By magnetizing the fusion fuel in inertial confinement fusion (ICF) systems, the required stagnation pressure and density can be relaxed dramatically. This happens because the magnetic field insulates the hot fuel from the cold pusher and traps the charged fusion burn products. This trapping allows the burn products to deposit their energy in the fuel, facilitating plasma self-heating. Here, we report on a comprehensive theory of this trapping in a cylindrical DD plasma magnetized with a purely axial magnetic field. Using this theory, we are able to show that the secondary fusion reactions can be used to infer the magnetic field-radius product, BR, during fusion burn. This parameter, not ρR, is the primary confinement parameter in magnetized ICF. Using this method, we analyze data from recent Magnetized Liner Inertial Fusion experiments conducted on the Z machine at Sandia National Laboratories. We show that in these experiments BR ≈ 0.34(+0.14/−0.06) MG · cm, a ∼ 14× increase in BR from the initial value, and confirming that the DD-fusion tritons are magnetized at stagnation. This is the first experimental verification of charged burn product magnetization facilitated by compression of an initial seed magnetic flux.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2014

Experimental demonstration of fusion-relevant conditions in magnetized liner inertial fusion

This Letter presents results from the first fully integrated experiments testing the magnetized liner inertial fusion concept [S.A. Slutz et al., Phys. Plasmas 17, 056303 (2010)], in which a cylinder of deuterium gas with a preimposed axial magnetic field of 10 T is heated by Z beamlet, a 2.5 kJ, 1 TW laser, and magnetically imploded by a 19 MA current with 100 ns rise time on the Z facility. Despite a predicted peak implosion velocity of only 70 km/s, the fuel reaches a stagnation temperature of approximately 3 keV, with T e ≈ T i , and produces up to 2e12 thermonuclear DD neutrons. In this study, X-ray emission indicates a hot fuel region with full width at half maximum ranging from 60 to 120 μm over a 6 mm height and lasting approximately 2 ns. The number of secondary deuterium-tritium neutrons observed was greater than 10 10 , indicating significant fuel magnetization given that the estimated radial areal density of the plasma is only 2 mg/cm 2 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2012

Nonlinear Amplification and Decay of Phase-mixed Waves in Compressing Plasma

Through particle-in-cell simulations, we show that plasma waves carrying trapped electrons can be amplified manyfold via compressing plasma perpendicularly to the wave vector. These simulations are the first ab initio demonstration of the conservation of nonlinear action for such waves, which contains a term independent of the field amplitude. In agreement with the theory, the maximum of amplification gain is determined by the total initial energy of the trapped-particle average motion but otherwise is insensitive to the particle distribution. Further compression destroys the wave; electrons are then untrapped at suprathermal energies and form a residual beam. As compression continues, the bump-on-tail instability is triggered each time one of the discrete modes comes in resonance with this beam. Hence, periodic bursts of the electrostatic energy are produced until a wide quasilinear plateau is formed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2012

Plasma-based Accelerator with Magnetic Compression

Electron dephasing is a major gain-inhibiting effect in plasma-based accelerators. A novel method is proposed to overcome dephasing, in which the modulation of a modest (~$\mathcal{O}$(10 kG)), axial, uniform magnetic field in the acceleration channel leads to densification of the plasma through magnetic compression, enabling direct, time-resolved control of the plasma wave properties. The methodology is broadly applicable and can be optimized to improve the leading acceleration approaches, including plasma beat-wave, plasma wakefield, and laser wakefield acceleration. The advantages of magnetic compression compared to other proposed schemes to overcome dephasing are identified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗