Engineering topics

Schmitz, Craig P.

Publications and source records attributed to Schmitz, Craig P..

5 records

NASA NTRS2011

Ares I-X First Stage Internal Aft Skirt Re-Entry Heating Data and Modeling

The CLVSTATE engineering code is being used to predict Ares-I launch vehicle first stage reentry aerodynamic heating. An engineering analysis is developed which yields reasonable predictions for the timing of the first stage aft skirt thermal curtain failure and the resulting internal gas temperatures. The analysis is based on correlations of the Ares I-X internal aft skirt gas temperatures and has been implemented into CLVSTATE. Validation of the thermal curtain opening models has been accomplished using additional Ares I-X thermocouple, calorimeter and pressure flight data. In addition, a technique which accounts for radiation losses at high altitudes has been developed which improves the gas temperature measurements obtained by the gas temperature probes (GTP). Updates to the CLVSTATE models are shown to improve the accuracy of the internal aft skirt heating predictions which will result in increased confidence in future vehicle designs

Schmitz, Craig P.↗

NASA NTRS2001

Space Science Payloads Optical Properties Monitor (OPM) Mission Flight Anomalies Thermal Analyses

The OPM was the first space payload that measured in-situ the optical properties of materials and had data telemetered to ground. The OPM was EVA mounted to the Mir Docking Module for an eight-month stay where flight samples were exposed to the Mir induced and natural environments. The OPM was comprised of three optical instruments; a total hemispherical spectral reflectometer, a vacuum ultraviolet spectrometer, and a total integrated scatterometer. There were also three environmental monitors; an atomic oxygen monitor, solar and infrared radiometers, and two temperature-controlled quartz crystal microbalances (to monitor contamination). Measurements were performed weekly and data telemetered to ground through the Mir data system. This paper will describe the OPM thermal control design and how the thermal math models were used to analyze anomalies which occurred during the space flight mission.

Schmitz, Craig P.↗

NASA NTRS1992

NLS cycle 1 and NLS 2 base heating technical notes. Appendix 3: Preliminary cycle 1 NLS base heating environments. Cycle 1 NLS base heating environments. NLS 2 650K STME base heating environments

A preliminary analysis of National Launch System ascent plume induced base heating environments has been completed to support the Induced Environments Panel's objective to assist in maturing the NLS vehicle (1.5 stage and heavy launch lift vehicle) design. Environments during ascent have been determined from this analysis for a few selected locations on the engine nozzles and base heat shield for both vehicles. The environments reflect early summer 1991 configurations and performance data and conservative methodology. A more complete and thorough analysis is under way to update these environments for the cycle 1 review in January 1992.

Bender, Robert L.↗

NASA NTRS1989

Boundary layer simulator improvement

Boundary Layer Integral Matrix Procedure (BLIMPJ) has been identified by the propulsion community as the rigorous boundary layer program in connection with the existing JANNAF reference programs. The improvements made to BLIMPJ and described herein have potential applications in the design of the future Orbit Transfer Vehicle engines. The turbulence model is validated to include the effects of wall roughness and a way is devised to treat multiple smooth-rough surfaces. A prediction of relaminarization regions is examined as is the combined effects of wall cooling and surface roughness on relaminarization. A turbulence model to represent the effects of constant condensed phase loading is given. A procedure is described for thrust decrement calculation in thick boundary layers by coupling the T-D Kinetics Program and BLIMPJ and a way is provided for thrust loss optimization. Potential experimental studies in rocket nozzles are identified along with the required instrumentation to provide accurate measurements in support of the presented new analytical models.

Praharaj, Sarat C.↗

NASA NTRS1987

Boundary layer simulation improvement

The current Boundary Layer Integral Matrix Procedure - Version J (BLIMPJ) is advanced with regard to the previously modeled calculation methods accounting for surface roughness, relaminarization, condensed phase, and thick boundary layer effects. Current analytical limitations will be relaxed to permit more realistic wall and flow conditions and to use appropriate turbulence models with specific emphasis for the projected Orbit Transfer Vehicle (OTV) engine application. The updates will be incorporated into the BLIMPJ computer program, and the modified program will be made operational on the MSFC CRAY computer system. Experimental feasibility studies were conducted to find out how to obtain quality test data with advanced instrumentation for concept verification purposes.

Praharaj, Sarat C.↗