Engineering topics

Schneider, Sebastian

Publications and source records attributed to Schneider, Sebastian.

6 records

DOE OSTI2024

Impact of Dilute DIO Additive on Local Microstructure of Fluorinated, pNDI‐Based Polymer Solar Cells

The performance of all‐polymer solar cells is often enhanced by incorporating solvent additives during solution processing. Here, in particular, blends based on the model all‐polymer system PBDBT:N2200 have been shown to have increased short‐circuit current and fill factor when processed with dilute diiodooctane (DIO). However, the morphological mechanism that drives the increase in performance is often not well understood due to limitations in common characterization techniques. In this study, it is shown that a combination of X‐ray techniques with cryogenic high‐resolution transmission electron microscopy (HRTEM) analysis can provide a quantitative and spatially resolved picture of polymer chain orientation and alignment in all‐polymer blends. It is found that DIO induces vertical phase separation in PBDBT‐2F:F‐N2200 and increases donor crystallite thickness in the pi‐stacking direction leading to an acceptor‐rich film surface. However, it is also shown that DIO does not disrupt the formation of face‐on donor–acceptor interfaces. These findings suggest that dilute DIO primarily affects crystalline domain formation in single component regions as opposed to mixed regions; thus, dilute DIO can impact vertical charge transport pathways without sacrificing donor–acceptor interfacial connectivity.

Cheng, Christina↗

DOE OSTI2023

Linking Phase Behavior to Performance Parameters in Non-Fullerene Acceptor Solar Cells

Performance of nonfullerene-based organic solar cells is largely dependent on the donor:acceptor blend morphology, which is initially tuned by composition. However, morphological design rules are difficult to identify due to the complex relationship between composition-dependent phase behavior and performance properties. In this study, the authors are able to establish a direct link between PM6:Y6 film morphology and device properties by combining grazing-incidence wide-angle X-ray scattering with highly sensitive Fourier transform photocurrent spectroscopy. By analyzing properties across the full composition range, interfacial microstructure and the corresponding charge transfer (CT) states are identified and direct structure–property relationships are established. Here the results indicate that open-circuit voltage is controlled by the CT state at amorphous-PM6:crystalline-Y6 interfaces. Crystalline Y6 is found to increase both transport and non-radiative recombination, suggesting that morphological tradeoffs may be necessary for overall device optimization.

14 SOLAR ENERGY↗

DOE OSTI2023

Effect of Molecular Weight on the Morphology of a Polymer Semiconductor–Thermoplastic Elastomer Blend

Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Use of a Multiple Hydride Donor To Achieve an n-Doped Polymer with High Solvent Resistance

We report the ability to insolubilize doped semiconducting polymer layers can help enable the fabrication of efficient multilayer solution-processed electronic and optoelectronic devices. Here, we present a promising approach to simultaneously n-dope and largely insolubilize conjugated polymer films using tetrakis[{4-(1,3-dimethyl-2,3-dihydro-1H-benzo[d]imidazol-2-yl)phenoxy}methyl]methane (tetrakis-O-DMBI-H), which consists of four 2,3-dihydro-1H-benzoimidazole (DMBI-H) n-dopant moieties covalently linked to one another. Doping a thiophene-fused benzodifurandione-based oligo(p-phenylenevinylene)-co-thiophene polymer (TBDOPV-T) with tetrakis-O-DMBI-H results in a highly n-doped film with bulk conductivity of 15 S cm –1 . Optical absorption spectra provide evidence for film retention of ~93% after immersion in o-dichlorobenzene for 5 min. The optical absorption signature of the charge carriers in the n-doped polymer decreases only slightly more than that of the neutral polymer under these conditions, indicating that the exposure to solvent also results in negligible dedoping of the film. Moreover, thermal treatment studies on a tetrakis-O-DMBI-H-doped TBDOPV-T film in contact with another undoped polymer film indicate immobilization of the molecular dopant in TBDOPV-T. This is attributed to the multiple electrostatic interactions between each dopant tetracation and up to four nearby anionic doped polymer segments.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Twisted A-D-A Type Acceptors with Thermally-Activated Delayed Crystallization Behavior for Efficient Nonfullerene Organic Solar Cells

We report that molecular aggregation and crystallization during film coating play a crucial role in the realization of high-performing organic photovoltaics. Strong intermolecular interactions and high solid-state crystallinity are beneficial for charge transport. However, fast crystallization during thin-film drying often limits the formation of the finely phase-separated morphology required for efficient charge generation. Herein, the authors show that twisted acceptor-donor-acceptor (A-D-A) type compounds, containing an indacenodithiophene (IDT) electron-rich core and two naphthalenediimide (NDI) electron-poor units, leads to formation of mostly amorphous phases in the as-cast film, which can be readily converted into more crystalline domains by means of thermal annealing. This design strategy solves the aforementioned conundrum, leading to an optimal morphology in terms of reduced donor/acceptor domain-separation sizes (ca. 13 nm) and increased packing order. Solar cells based on these acceptors with a PBDB-T polymer donor show a power conversion efficiency over 10% and stable morphology, which results from the combined properties of desirable excited-state dynamics, high charge mobility, and optimal aggregation/crystallization characteristics. These results demonstrate that the twisted A-D-A motif featuring thermally-induced crystallization behavior is indeed a promising alternative design approach toward more morphologically robust materials for efficient organic photovoltaics.

14 SOLAR ENERGY↗

DOE OSTI2021

Achieving High Thermoelectric Performance and Metallic Transport in Solvent-Sheared PEDOT:PSS

Polymer-based materials hold great potential for use in thermoelectric applications but are limited by their poor electrical properties. Through a combination of solution-shearing deposition and directionally applied solvent treatments, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films with metallic-like conductivities can be obtained with high power factors in excess of 800 µW m -1 K -2 . X-ray scattering and absorption data indicate that structural alignment of PEDOT chains and larger-sized domains are responsible for the enhanced electrical conductivity. Overall, it is expected that further enhancements to the power factor can be obtained through device geometry and postdeposition solvent shearing optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗