Search NASA⌕ Search

Engineering topics

Schock, A.

Publications and source records attributed to Schock, A..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Design and spacecraft-integration of RTGs for solar probe

The design, analysis, and spacecraft integration of radioisotope thermoelectric generators (RTG) to power the Solar Probe under study at NASA JPL is described. The mission of the Solar Probe is to explore the solar corona by performing in situ measurements at up to four solar radii to the sun. Design constraints for the RTG are discussed. The chief challenge in the design and system integration of the Solar Probe's RTG is a heat rejection problem. Two RTG orientations, horizontal and oblique, are analyzed for effectiveness and results are summarized in chart form. A number of cooling strategies are also investigated, including heat-pipe and reflector-cooled options. A methodology and general computer code are presented for analyzing the performance of arbitrarily obstructed RTGs with both axial and circumferential temperature, voltage, and current variation. This methodology is applied to the specific example of the Solar Probe RTG obstructed by a semicylindrical reflector of 15-inch radius.

Schock, A.↗
NASA NTRS1989

Mars rover RTG study

The paper describes the design and analysis of radioisotope thermoelectric generators (RTGs) for powering the Mars rover vehicle, which is a critical element of the unmanned Mars Rover and Sample Return mission (MRSR). A brief description is given of a reference mission scenario, an illustrative rover design and activity pattern on Mars, power system requirements, and environmental constraints, including the RTG cooling requirements during transit to Mars. The key RTG design problem, i.e. venting the helium generated by the fuel's alpha decay without intrusion of the Martian atmosphere into the RTG, is identified and a design approach to solve that problem is proposed. The study's primary objective is to quantify the performance improvements achievable in new successfully developed technologies, to estimate the required time, effort, success probability, and programmatic risk in developing these new technologies, and thus to help identify the best strategy for meeting the MRSR system goals. Finally, the paper compares the RTGs' specific powers for different power levels (250W vs 125W), different thermoelectric element designs (standard vs short unicouples vs multicouples), and different thermoelectric figures of merit (0.00058K to the -1 to 0.00140K to the -1).

Schock, A.↗
NASA NTRS1989

Requirements and designs for Mars Rover RTGs

A typical Rover mission, its requirements, the environment it imposes on the radionuclide thermoelectric generator (RTG), and a design approach for making the RTG operable in such an environment are described. Specific RTG designs for various thermoelectric element alternatives are presented. The results of studies show that current multifoil-insulated GPHS (general-purpose heat source) RTG and Mod-RTG designs can be modified to operate in an environment with an external atmosphere (e.g., Mars). This can be done while the helium generated by the fuel's alpha decay is vented to the external atmosphere. The use of novel selective vents and high-capacity getters is not required. The Rover RTGs can be built from standard, proven GPHS modules and standard SiGe unicouples or SiGe/GaP multicouples, using demonstrated thermoelectric material performance parameters. Rover's 500-W power requirement can be satisfied with two 250-W or four 125-W RTGs, whose sizes are compatible with currently envisaged Rover designs. An auxiliary cooling loop (e.g., water and antifreeze) will be required to cool the RTG while it is within the Rover's aeroshell during launch and transit to Mars.

Schock, A.↗
NASA NTRS1971

Design, fabrication, and testing of an external fuel (UO2), full-length thermionic converter

The development of a full-length external-fuel thermionic converter for in-pile testing is described. The development program includes out-of-pile performance testing of the fully fueled-converter, using RF-induction heating, before its installation in the in-pile test capsule. The external-fuel converter is cylindrical in shape, and consists of an inner, centrally cooled collector, and an outer emitter surrounded by nuclear fuel. The term full-length denotes that the converter is long enough to extend over the full height of the reactor core. Thus, the converter is not a scaled-down test device, but a full-scale fuel element of the thermionic reactor. The external-fuel converter concept permits a number of different design options, particularly with respect to the fuel composition and shape, and the collector cooling arrangement. The converter described was developed for the Jet Propulsion Laboratory, and is based on their concept for a thermionic reactor with uninsulated collector cooling as previously described. The converter is double-ended, with through-flow cooling, and with ceramic seals and emitter and collector power take-offs at both ends. The design uses a revolver-shaped tungsten emitter body, with the central emitter hole surrounded by six peripheral fuel holes loaded with cylindrical UO2 pellets.

Schock, A.↗
NASA NTRS1971

Development of a full-length external-fuel thermionic converter for in-pile testing.

Description of an external-fuel thermionic converter which utilizes a thoriated-tungsten fuel-emitter body. Performance in out-of-pile tests was comparable to that of an arc-cast tungsten emitter body, with 400-eW output power (about 5 W/sq cm) at 10.8% efficiency. Maximum fuel clad temperature averaged from 1650 to 1700 C during the 300-hour test. This converter has been processed for in-pile testing. The various processing steps, including the installation of six emitter thermocouples, encapsulation in the secondary container, and joining to the fission-gas collection system, are described in detail. In addition to the converter assembly, a doubly contained fission gas collection assembly with radiation-hardened differential pressure transducers was fabricated. The experiment support plate required for the in-pile test, containing electrically insulated instrumentation feedthroughs and coolant line feedthroughs to the vacuum test chamber, was also fabricated.

Schock, A.↗