Search NASA⌕ Search

Engineering topics

Schulthess, Jason L

Publications and source records attributed to Schulthess, Jason L.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Non-destructive Post-Transient Examination Results of the MOXTOP-1 Experiment

The MOXTOP-1 experiment has been assembled and irradiated in INL’s HFEF and TREAT facilities followed by disassembly of the experiment to enable initial post-transient examination. Results of neutron radiography of the fuel pin still in the THOR capsule were somewhat inconclusive due to the additional scatter and attenuation from the iron heat sink included in the design. Nonetheless, no obvious failure or fuel relocation could be identified in the radiography. Following disassembly of the fuel pin from the capsule, initial visual inspections were performed, and documented via images obtained through the hot cell window. No obvious signs of fuel failure were identified, indicating that the fuel pin remained intact during the transient. Some discoloration was observed near the middle of the fuel pin, likely corresponding to the fueled zone indicating that that region may have reached a relatively high temperature. Pre-transient, and post-transient profilometry of the fuel pin were performed and compared. Some additional strain displacement in the bottom portion of the fuel zone is identified, but remains well below 1%.

Mixed Oxide↗
DOE OSTI2024

Resumption of SFR Overpower Testing and Post-Transient Examination of the THOR-C-2 Irradiation Test

Transient overpower testing for fuel safety research and development has resumed at Idaho National Laboratory. The THOR-C-2 commissioning test has been performed and post-transient examination has been performed revealing the intended creep rupture failure near the top of the fuel zone. This paves the way for future testing on previously irradiated fuels that will support fuel development and qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Resumption of SFR Overpower Testing and Post-Transient Examination of the THOR-C-2 Irradiation Test

Transient overpower testing for fuel safety research and development has resumed at Idaho National Laboratory. The THOR-C-2 commissioning test has been performed and post-transient examination has been performed revealing the intended failure near the top of the fuel zone. This paves the way for future testing on previously irradiated fuels that will support fuel development and qualification.

advanced reactors↗
DOE OSTI2024

FUEL PERFORMANCE STUDIES AT IDAHO NATIONAL LABORATORY MAKING USE OF THE BYRON FUEL SHIPMENT

In December of 2023 a shipment of commercially irradiated fuel rods from the Byron Generating Station in Illinois was successfully shipped to the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The make-up of the rods includes a mix of cladding types from traditional ZirloTM, advanced zirconium alloys, and chrome coated ZirloTM. Burnups range from regular end of life values to over 70 GWd/MTU rod average. The R&D plan for the rods involves multiple projects from developing licensing data for new claddings to integral transient tests to support burnup extension efforts in the United States. The R&D began in early 2024 with the nondestructive examinations of the rods after which they will be sectioned for microscopy, mechanical testing, and analytical chemistry. Additionally, many rod segments will be refabricated into new test pins and inserted into a static water capsule for integral Reactivity Initiated Accident (RIA) and Loss of Coolant Accident (LOCA) testing at the TREAT reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Thermal Conductivity Degradation in High Burnup U-Pu-Zr Fuel

Recent advancements in the characterization of irradiated U-Pu-Zr fuels have revealed complexities that challenge existing understanding of constituent redistribution. Traditionally, models have proposed three concentric regions within the fuel, each characterized by distinctive phases and porosity. However, through detailed analysis of high burnup U-Pu-Zr, we discovered the presence of four distinct constituent redistribution regions. Particularly novel is the observation of significant Pu redistribution, a previously unreported phenomenon that necessitates a reevaluation of current models. This work aims to delve deeper into these findings, seeking to correlate mesoscale measurements of thermal diffusivity and respective thermal conductivity with the phases present in each redistribution region. To achieve this objective, we employed mesoscale thermoreflectance methods using the unique, Idaho National Laboratory (INL) developed, Thermal Conductivity Microscope (TCM) at INL’s Irradiated Materials Characterization Laboratory. The TCM employs two tightly focused lasers: one for heating to generate periodic thermal waves in the substrate, and another spatially separated probe laser to detect changes in the optical reflectivity of the gold-coated substrate resulting from thermal wave diffusion. We conducted several thermal diffusivity measurements within each region of constituent redistribution of a U-19Pu-10Zr fuel pin cross section irradiated to 11 at. % burnup. The TCM measurement positions strategically aligned with transmission electron microscopy (TEM) lift-out locations previously collected from the fuel sample. Complementary microstructural analysis techniques such as optical and scanning electron microscopy (OM/SEM), electron probe microanalysis for chemical compositions, and TEM-based selective area electron diffraction (SAED) analysis for crystallographic insights into each phase were also utilized. This comprehensive approach allowed us to correlate local thermal diffusivity data with microstructural characteristics, enabling the computation of local thermal conductivity at each position. The significance of this contribution lies in its pioneering use of the TCM for ternary fuel mesoscale examination, shedding light on the previously overlooked effects of Pu redistribution on local thermal conductivity. By informing current models capturing constituent redistribution and heat transfer, our findings pave the way for more accurate predictions of metallic fuel performance. Moreover, this work sets the stage for future comparisons with similar TCM examinations on U-19Pu-10Zr fuels at ultra-low burnup, facilitating a comprehensive understanding of thermal property changes across different burnup levels. Ultimately, our study not only enriches our understanding of the thermophysical properties of individual redistribution regions within U-Pu-Zr fuel but also offers valuable insights for the design and operational parameters of proposed next-generation fast reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Mapping the Microstructure During the Historic U-Mo Monolithic Fuel Foil Fabrication Process

Since 2004, there has been extensive effort towards the development of a uranium molybdenum monolithic fuel system to convert high performance research and test reactors. The RERTR-6 experiment was the first to attempt a monolithic fuel instead of a dispersed fuel form. The fabrication methods evolved overtime and provided the basis for current fabrication methods. The various steps in the process inevitably tailor the fuel alloy microstructure which is known to influence irradiation behavior. This document aims to present and discuss the fabrication evolution that transpired through a recounting of historical data from the various fabrication campaigns. By overlaying this data with basic science studies on the U-Mo that explored transformation kinetics, it is possible to estimate a measure of the impact heat treatments have on the final as-fabricated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Pre-Transient Characterization of Historic EBR-II Pins for Transient Testing

Current interest in sodium-cooled fast reactor (SFR) designs, such as TerraPower’s Natrium Reactor, has highlighted the need for advanced reactor fuel technology development. Modern U-Zr and U- Pu-Zr pin designs are primary candidates to fuel SFRs and boast high fuel utilization capacity, increased fuel-cladding compatibility, and improved safety through inherent feedback mechanisms. Despite over 60 years of metallic fuel irradiation, uncertainties exist in the performance of the fuel system, particularly under transient overpower (TOP) and loss of flow (LOF) scenarios. Throughout historical testing within the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF), fuel behavior has demonstrated benign response to transient reactor conditions; however, accurate predictions of failure thresholds to inform operational limitations rely heavily on fuel composition, burnup, and irradiation history. In expanding TOP and LOF testing, the Transient Heat sink Overpower Response (THOR) Capsule will be used to test modern fuel technologies in a static sodium environment in the Transient Reactor Test (TREAT) Facility. The THOR capsule is highly instrumented and will provide time-dependent thermal behavior of SFR fuel pins subjected to accident conditions within TREAT. The THOR-Metallic (THOR- M) campaign aims to validate and expand historical TOP and LOF testing on high burnup U-Zr and U-Pu- Zr fuel alloys previously irradiated in EBR-II by running the rods to failure. This contribution focuses primarily on the pre-transient engineering-scale destructive and non- destructive characterization that has been conducted on both the test and sibling pins used for the TOP and LOF tests. All pins underwent visual examination, neutron radiography, element contact profilometry, and precise gamma scan. The sibling pins used for each test were further analyzed using gas assay, sampling, and recharge analysis (GASR), and optical microscopy. The results from each technique confirmed that the fuel pins were intact and devoid of any atypical developments when compared to historical data. Additionally, the analyzed measurements establish a baseline for comparison to post-transient analysis. Key fuel behaviors quanitifed include axial elongation of the fuel column, diametral strain of the pin, patterns in fluff structure geometry, changes in axial isotope distribution, evolution of constituent redistribution, porosity, and fission gas release. The pre-transient measurements and changes attributed to transient behavior from post-transient measurement will be compared to historical data to capture the behavioral dependence on composition, burnup, and irradiation history. Results from this work advance the initiatives of the THOR-M campaign, which aid in informing fuel performance models and establishing safety criteria for SFR operational limits. The novel combination of test environment, in-situ instrumentation, and comprehensive suite of characterization methods provides greater understanding of transient fuel behavior. Overall, information on the time and condition of pin failure for high burnup U-Pu-Zr will greatly expand the limited existing TOP and LOF test data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Pre-Transient Characterization of Historic EBR-II Pins for Transient Testing

Current interest in sodium-cooled fast reactor (SFR) designs, such as TerraPower’s Natrium Reactor, has highlighted the need for advanced reactor fuel technology development. Modern U-Zr and U- Pu-Zr pin designs are primary candidates to fuel SFRs and boast high fuel utilization capacity, increased fuel-cladding compatibility, and improved safety through inherent feedback mechanisms. Despite over 60 years of metallic fuel irradiation, uncertainties exist in the performance of the fuel system, particularly under transient overpower (TOP) and loss of flow (LOF) scenarios. Throughout historical testing within the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF), fuel behavior has demonstrated benign response to transient reactor conditions; however, accurate predictions of failure thresholds to inform operational limitations rely heavily on fuel composition, burnup, and irradiation history. In expanding TOP and LOF testing, the Transient Heat sink Overpower Response (THOR) Capsule will be used to test modern fuel technologies in a static sodium environment in the Transient Reactor Test (TREAT) Facility. The THOR capsule is highly instrumented and will provide time-dependent thermal behavior of SFR fuel pins subjected to accident conditions within TREAT. The THOR-Metallic (THOR- M) campaign aims to validate and expand historical TOP and LOF testing on high burnup U-Zr and U-Pu- Zr fuel alloys previously irradiated in EBR-II by running the rods to failure. This contribution focuses primarily on the pre-transient engineering-scale destructive and non- destructive characterization that has been conducted on both the test and sibling pins used for the TOP and LOF tests. All pins underwent visual examination, neutron radiography, element contact profilometry, and precise gamma scan. The sibling pins used for each test were further analyzed using gas assay, sampling, and recharge analysis (GASR), and optical microscopy. The results from each technique confirmed that the fuel pins were intact and devoid of any atypical developments when compared to historical data. Additionally, the analyzed measurements establish a baseline for comparison to post-transient analysis. Key fuel behaviors quanitifed include axial elongation of the fuel column, diametral strain of the pin, patterns in fluff structure geometry, changes in axial isotope distribution, evolution of constituent redistribution, porosity, and fission gas release. The pre-transient measurements and changes attributed to transient behavior from post-transient measurement will be compared to historical data to capture the behavioral dependence on composition, burnup, and irradiation history. Results from this work advance the initiatives of the THOR-M campaign, which aid in informing fuel performance models and establishing safety criteria for SFR operational limits. The novel combination of test environment, in-situ instrumentation, and comprehensive suite of characterization methods provides greater understanding of transient fuel behavior. Overall, information on the time and condition of pin failure for high burnup U-Pu-Zr will greatly expand the limited existing TOP and LOF test data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Advances in Metallic Fuel Database Development and Data Qualification

The Fuels Irradiation and Physics Database (FIPD [1]) is a comprehensive repository of data and documents related to Uranium-Zirconium based metallic fuel test pins. This database stores operational conditions of these pins, calculated using a suite of Argonne National Laboratory analysis codes developed during the Integral Fast Reactor (IFR) program. Key calculated data include axial distributions of power, temperature, fluence, burnup, and isotopic densities. Additionally, the FIPD holds post-irradiation examination (PIE) data such as fission gas release, gas chemistry measurements, and axial distributions derived from profilometry, gamma scanning, and neutron radiography. Complementing these data is an extensive archive of documents related to various pins and experiments. These include raw PIE records, design details, safety analyses, and operational reports. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). The recent improvements to the database and the data QA status are summarized in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗