Engineering topics

Schuster, L. S.

Publications and source records attributed to Schuster, L. S..

6 records

NASA NTRS1985

Stress analyses of B-52 pylon hooks

The NASTRAN finite element computer program was used in the two dimensional stress analysis of B-52 carrier aircraft pylon hooks: (1) old rear hook (which failed), (2) new rear hook (improved geometry), (3) new DAST rear hook (derated geometry), and (4) front hook. NASTRAN model meshes were generated by the aid of PATRAN-G computer program. Brittle limit loads for all the four hooks were established. The critical stress level calculated from NASTRAN agrees reasonably well with the values predicted from the fracture mechanics for the failed old rear hook.

Ko, W. L.↗

NASA NTRS1984

NASTRAN/FLEXSTAB procedure for static aeroelastic analysis

Presented is a procedure for using the FLEXSTAB External Structural Influence Coefficients (ESIC) computer program to produce the structural data necessary for the FLEXSTAB Stability Derivatives and Static Stability (SD&SS) program. The SD&SS program computes trim state, stability derivatives, and pressure and deflection data for a flexible airplane having a plane of symmetry. The procedure used a NASTRAN finite-element structural model as the source of structural data in the form of flexibility matrices. Selection of a set of degrees of freedom, definition of structural nodes and panels, reordering and reformatting of the flexibility matrix, and redistribution of existing point mass data are among the topics discussed. Also discussed are boundary conditions and the NASTRAN substructuring technique.

Schuster, L. S.↗

NASA NTRS1984

Preflight transient dynamic analyses of B-52 aircraft carrying Space Shuttle solid rocket booster drop-test vehicle

This paper concerns the transient dynamic analysis of the B-52 aircraft carrying the Space Shuttle solid rocket booster drop test vehicle (SRB/DTV). The NASA structural analysis (NASTRAN) finite element computer program was used in the analysis. The B-52 operating conditions considered for analysis were (1) landing and (2) braking on aborted takeoff runs. The transient loads for the B-52 pylon front and rear hooks were calculated. The results can be used to establish the safe maneuver envelopes for the B-52 carrying the SRB/DTV in landings and brakings.

Ko, W. L.↗

NASA NTRS1983

Pre-flight transient dynamic analysis of B-52 carrying Space Shuttle solid rocket booster drop-test vehicle

This paper concerns the transient dynamic analysis of the B-52 aircraft carrying the Space Shuttle solid-rocket booster drop-test vehicle (SRB/DTV). The NASA structural analysis (NASTRAN) finite-element computer program was used in the analysis. The B-52 operating conditions considered for analysis were (1) landing and (2) braking on aborted takeoff runs. The transient loads for the B-52 pylon front and rear hooks were calculated. The results can be used to establish the safe maneuver envelopes for the B-52 carrying the SRB/DTV in landings and brakings.

Ko, W. L.↗

NASA NTRS1981

Preflight reentry heat transfer analysis of Space Shuttle

Preflight predictions of the structural temperature distributions during entry are compared with data from the initial Shuttle flight. Finite element thermal analysis programming was used to model the heat flow on Shuttle structures and actual gas properties of air were employed in the analyses of aerodynamic heating. Laminar, separated, and turbulent heat fluxes were calculated for varying locations on the craft using velocity-attitude and angle-of-attack projections taken from the nominal STS-1 trajectory. Temperature time histories of the first flight are compared with laminar and turbulent flow assumptions and an unpredicted rapid cooling 1800 sec into entry is credited to inaccurate assumptions of structural heat dissipative properties or flow conditions in that time phase of the flight; additional discrepancies in descriptions of heating of the upper fuselage are attributed to a lack of knowledge of the complex flow patterns existing over that area of the Shuttle body.

Ko, W. L.↗

NASA NTRS1978

Correlation of predicted and measured thermal stresses on a truss-type aircraft structure

A test structure representing a portion of a hypersonic vehicle was instrumented with strain gages and thermocouples. This test structure was then subjected to laboratory heating representative of supersonic and hypersonic flight conditions. A finite element computer model of this structure was developed using several types of elements with the NASA structural analysis (NASTRAN) computer program. Temperature inputs from the test were used to generate predicted model thermal stresses and these were correlated with the test measurements.

Jenkins, J. M.↗