Search NASA⌕ Search

Engineering topics

Schutte, Aaron

Publications and source records attributed to Schutte, Aaron.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Mid-Air Helicopter Delivery at Mars Using a Jetpack

Mid-Air Helicopter Delivery (MAHD) is a new Entry, Descent and Landing (EDL) architecture to enable in situ mobility for Mars science at lower cost than previous rover missions. It uses a jetpack to slow down a Mars Science Helicopter (MSH) after separation from the backshell, and reach aerodynamic conditions suitable for helicopter take-off in mid air. MAHD's lander-free approach leaves enough room in the aeroshell to accommodate larger rotors. This drastically improves flight performance compared to heritage EDL approaches, notably +60\% science payload mass. MAHD also brings cost savings, a simpler architecture, improved surface access and can reach higher elevations on Mars. This paper introduces a design for the MAHD system architecture and operations. We present a mechanical configuration which fits both MSH and the jetpack within the 2.65-m Mars heritage aeroshell, and a jetpack control architecture which fully leverages the available helicopter avionics. We discuss preliminary numerical models of the flow dynamics resulting from the interaction between the jets, the rotors and the side winds. We define a force-torque sensing architecture capable of handling the wind and trimming the rotors to prepare for safe take-off. Finally, we analyze the dynamic environment and closed-loop control simulation results to demonstrate the preliminary feasibility of MAHD.

Balaram, J.↗
NASA NTRS2021

Prototype Development of a Variable Altitude Venus Aerobot

This paper presents the design methodology and results from the first subscale prototype jointly developed by JPL and Near Space Corporation for a variable altitude Venus aerobot. This vehicle is based on the principle of a two-part balloon for which pumping helium gas between the balloons can modulate buoyancy and thereby control the altitude of the vehicle. The intended mission application at Venus is a cloud-level exploration across an altitude range of 52 to 62 kilometers for weeks or months, circumnavigating the planet multiple times and carrying an approximately 100 kg payload module containing all scientific instruments, avionics and other vehicle support systems. The first prototype is approximately one-third scale (4 m diameter) and serves as a proof-of-concept test article allowing for evaluation of manufacturing approaches and laboratory testing to evaluate performance. Two key design features of the prototype as built are the use of Teflon film on the outside of the balloon to protect it from the sulfuric acid aerosols in the Venusian atmosphere and second surface metallization of that film to reflect most incident sunlight and thereby limit diurnal temperature and the associated temperature-driven pressure fluctuations. This prototyping effort has been complemented with a detailed vehicle simulation activity that incorporates the relevant balloon physics and thereby models the expected dynamic behavior of the aerobot in both the Earth and Venus atmospheres. Data obtained in laboratory tests of the prototype have been used to validate, verify and update that simulation model as described in the paper.

Turner, Caleb↗
NASA NTRS2021

Aerocapture Trajectories for Earth Orbit Technology Demonstration and Orbiter Science Missions at Venus, Earth, Mars, and Neptune

The use of aerocapture to provide the delta-V needed to capture a spacecraft into orbit can provide significant fuel savings compared to a propulsive orbit insertion. The aerocapture guidance method described in this paper uses drag modulation, which deploys a drag skirt in the atmosphere until the amount of delta-V needed to capture into the desired orbit is obtained, at which time the drag skirt is separated from the spacecraft. By modulating the time of drag skirt jettison, the vehicle can target a specific orbit apoapsis in the presence of uncertainties such as entry targeting errors and unknown atmospheric conditions.

Jadusingh, Matt↗
NASA NTRS2020

Motivations and Preliminary Design for Mid-Air Deployment of a Science Rotorcraft on Mars

Mid-Air Deployment (MAD) of a rotorcraft during Entry, Descent and Landing (EDL) on Mars eliminates the need to carry a propulsion or airbag landing system. This reduces the total mass inside the aeroshell by more than 100 kg, aeroshell complexity, and likely the risk and cost associated to the mission. Moreover, the lighter entry mass enables landing in the Martian highlands, at elevations inaccessible to current EDL technologies. This paper proposes a novel MAD concept for a Mars helicopter. We suggest a minimum science payload package to perform relevant science in the highlands. A variant of the Ingenuity helicopter is proposed to provide increased deceleration during MAD, and enough lift to fly the science payload in the highlands. We show in simulation that the lighter aeroshell results in lower terminal velocity (30 m/s) at the end of the parachute phase of the EDL, and at higher altitudes than other approaches. After discussing the aerodynamics, controls, guidance and mechanical challenges associated to deploying at such speed, we propose a backshell architecture that addresses them to release the helicopter in the safest conditions. Finally, we implemented the helicopter model and aerodynamic descent perturbations in the JPL Dynamics and Real-Time Simulation (DARTS) framework. Preliminary performance evaluation indicate landing and helicopter operations can be achieved up to +5 km MOLA.

Rapin, William↗
NASA NTRS2020

Terrain Relative Navigation for Guided Descent on Titan

Titan’s dense atmosphere, low gravity, and high winds at high altitudes create descent times of >90 minutes with standard entry/descent/landing (EDL) architectures and result in large unguided landing ellipses, with 99% values of 110x110 km and 149x72 km in recent Titan lander proposals. Enabling precision landing on Titan could increase science return for the types of missions proposed to date and make additional types of landing sites accessible, opening up new possibilities for science investigations. Precision landing on Titan has unique challenges, because the hazy atmosphere makes it difficult to see the surface and because it requires guided descent with divert ranges that are one to two orders of magnitude larger than needed for other target bodies, i.e. up to on the order of 100 km. It is conceivable that such a divert capability could be provided economically by a parafoil or other steerable aerodynamic decelerator deployed several 10s of km above the surface. The long descent times lead to large inertial navigation errors, hence a need for terrain relative navigation (TRN). This would require a TRN capability that can operate at such altitudes, despite challenges of seeing the surface sufficiently clearly and of depending on map products that are two orders of magnitude lower in spatial resolution than those for Mars and airless bodies. We then develop algorithms for map matching and feature tracking with descent images and test these with synthetic images created from Cassini/Huygens data sets and our radiative transfer model. We also introduce new possibilities for TRN based on the potential to discriminate some specific types of terrain onboard in descent imagery, such as lake vs adjacent ground and dune vs interdune. We use sensor measurement noise models in simulations of state estimation with an extended Kalman filter that includes coordinates of a set of tracked features in the state vector. Case studies were done for two notional landing sites, one in a site with only dry ground and one in a Titan lake district. In both cases, the filter error model shows 3 position error at touchdown on the order of 2 km. More work is needed to validate these results with higher fidelity camera models and larger data sets, but this is very promising.

Matthies, Larry↗
NASA NTRS2019

Aero Maneuvering Dynamics and Control for Precision Landing on Titan

We have developed and tested several dynamic models of the parafoil system descending in Titan’s atmosphere. These dynamic models include a progression from point mass models to rigid multibody models, including relative dynamics between canopy and payload. In these models, we have included wind models used for Titan simulation, and extrapolated wind gust models previously used for simulation in the Martian environment. We have also developed guidance and control techniques to for autonomous parafoil turning in the adverse wind environment. Finally, and in order to improve the controller performance by reducing the uncertainty to environmental factors, we have also developed ways to estimate the Titan environmental parameters, i.e. the atmospheric density, and the wind magnitude, during the descent. A more complete and realistic simulation is being developed, which uses JPL’s DSENDS Entry, Descent, and Landing Software framework.

Ermolli, Luca↗