Engineering topics

Schwartz, Joseph

Publications and source records attributed to Schwartz, Joseph.

4 records

DOE OSTI2020

Final Report – Cooperative Research and Development Agreement between National Energy Technology Laboratory and Praxair, Inc.

Praxair and DOE-NETL entered into a collaborative research and development agreement (CRADA) in March 2019 to evaluate economic viability of chemical looping processes for hydrogen, CO, and syngas production in comparison to state-of-the-art conventional processes. Praxair had developed process configurations for producing hydrogen and CO using chemical looping processes. NETL had modeling and system design experience for the chemical looping reactor system. The goal for NETL is to provide performance and design information regarding the chemical looping portion of a potential commercial plant. Praxair’s goal is to evaluate chemical looping processes and try to identify a process that can be commercially relevant within a few years. A key to success for the program will be to develop a chemical looping reactor system that enables significant capital cost reduction and performance improvement for the overall process. This report describes chemical looping-based CO production process, chemical looping reactor system and oxygen carrier material as well as summary of technoeconomic analysis results. Also included in the report are a list of assumptions that were used for designing the chemical looping plant and a list of areas for further study required to validate some of these assumptions in future efforts. The initial goal was to design two chemical looping plants. Case 1 would produce 1 MM scfd Hydrogen from NG, and Case 2 would co-produce hydrogen and 5 MM scfd CO from NG. However, later in the collaboration, it was decided to drop Case 1 as Case 2 process already included hydrogen production.

Bayham, Samuel↗

DOE OSTI2018

Graphic statics and their potential for digital design and fabrication with concrete

The paper describes the influence of the lower bound theorem of theory of plasticity on the design of structures during the last 70 years. Starting with the fundamental theorems developed in the middle of the last century, the influence of rigid plastic (discontinuous) stress fields on the design of reinforced beam, wall, slab and shell structures is worked out. The potential of graphic statics for digital design and fabrication is illustrated by the results of several research projects on form finding and design of reinforced concrete structures carried out during the last decade. It is shown that the design methods allow for simultaneous considerations about structure and architecture. This leads to leaner structure and reduced material consumption. However, while a current limitation of manufacturing objects in these ''nonstandard'' shapes is presently cost limiting, digital fabrication may change this and open a much greater scope for the use and application of graphic statics in a near future.

36 MATERIALS SCIENCE↗

DOE OSTI2015

Advanced Hydrogen Transport Membrane for Coal Gasification

A pilot-scale hydrogen transport membrane (HTM) separator was built that incorporated 98 membranes that were each 24 inches long. This separator used an advanced design to minimize the impact of concentration polarization and separated over 1000 scfh of hydrogen from a hydrogen-nitrogen feed of 5000 scfh that contained 30% hydrogen. This mixture was chosen because it was representative of the hydrogen concentration expected in coal gasification. When tested with an operating gasifier, the hydrogen concentration was lower and contaminants in the syngas adversely impacted membrane performance. All 98 membranes survived the test, but flux was lower than expected. Improved ceramic substrates were produced that have small surface pores to enable membrane production and large pores in the bulk of the substrate to allow high flux. Pd-Au was chosen as the membrane alloy because of its resistance to sulfur contamination and good flux. Processes were developed to produce a large quantity of long membranes for use in the demonstration test.

08 HYDROGEN↗

DOE OSTI2011

Advanced Hydrogen Liquefaction Process

The project identified and quantified ways to reduce the cost of hydrogen liquefaction, and reduce the cost of hydrogen distribution. The goal was to reduce the power consumption by 20% and then to reduce the capital cost. Optimizing the process, improving process equipment, and improving ortho-para conversion significantly reduced the power consumption of liquefaction, but by less than 20%. Because the efficiency improvement was less than the target, the program was stopped before the capital cost was addressed. These efficiency improvements could provide a benefit to the public to improve the design of future hydrogen liquefiers. The project increased the understanding of hydrogen liquefaction by modeling different processes and thoroughly examining ortho-para separation and conversion. The process modeling provided a benefit to the public because the project incorporated para hydrogen into the process modeling software, so liquefaction processes can be modeled more accurately than using only normal hydrogen. Adding catalyst to the first heat exchanger, a simple method to reduce liquefaction power, was identified, analyzed, and quantified. The demonstrated performance of ortho-para separation is sufficient for at least one identified process concept to show reduced power cost when compared to hydrogen liquefaction processes using conventional ortho-para conversion. The impact of improved ortho-para conversion can be significant because ortho para conversion uses about 20-25% of the total liquefaction power, but performance improvement is necessary to realize a substantial benefit. Most of the energy used in liquefaction is for gas compression. Improvements in hydrogen compression will have a significant impact on overall liquefier efficiency. Improvements to turbines, heat exchangers, and other process equipment will have less impact.

08 HYDROGEN↗