Search NASA⌕ Search

Engineering topics

Schy, A. A.

Publications and source records attributed to Schy, A. A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Control of elastic robotic systems by nonlinear inversion and modal damping

Energy efficient, lightweight robot arms for space applications have considerable structural flexibility. For large and fast motions, both the nonlinear coupled dynamics and the elastic behavior of the robots must be considered in control system designs. This paper presents an approach to the control of a class of flexible robotic systems. A control law is derived which decouples the joint-angle motion from the flexible motion and asymptotically decomposes the elastic dynamics into two subsystems, representing the transverse vibrations of the elastic link in two orthogonal planes. This decomposition allows the design of an elastic mode stabilizer independently based on lower order models representing structural flexibility. The closed-loop system is shown to be globally asymptotically stable and robust to uncertainty in system parameters. Simulation results are presented to show that large, fast control of joint angles can be performed in spite of space vehicle motion and uncertainty in the payload.

Singh, S. N.↗
NASA NTRS1986

Elastic robot control - Nonlinear inversion and linear stabilization

An approach to the control of elastic robot systems for space applications using inversion, servocompensation, and feedback stabilization is presented. For simplicity, a robot arm (PUMA type) with three rotational joints is considered. The third link is assumed to be elastic. Using an inversion algorithm, a nonlinear decoupling control law u(d) is derived such that in the closed-loop system independent control of joint angles by the three joint torquers is accomplished. For the stabilization of elastic oscillations, a linear feedback torquer control law u(s) is obtained applying linear quadratic optimization to the linearized arm model augmented with a servocompensator about the terminal state. Simulation results show that in spite of uncertainties in the payload and vehicle angular velocity, good joint angle control and damping of elastic oscillations are obtained with the torquer control law u = u(d) + u(s).

Singh, S. N.↗
NASA NTRS1985

Decomposition and state variable feedback control of elastic robotic systems

Energy-efficient, lightweight robot arms for space applications have considerable structural flexibility. An approach to control of a class of flexible robotic systems is presented. A control law is derived which decouples the joint-angle motion from the flexible motion and, in addition, asymptotically decomposes the elastic dynamics into two subsystems. This allows the design of an elastic mode stabilizer independently based on lower order models representing structural flexibility. The closed-loop system is shown to be globally asymptotically stable and robust to uncertaintly in system parameters. Simulation results show that the combination of nonlinear decoupling and elastic stabilization permits rapid, accurate tracking of large joint angle commands with well damped elastic response, in spite of space vehicle motion and payload uncertainty.

Singh, S. N.↗
NASA NTRS1985

Robust torque control of an elastic robotic arm based on invertibility and feedback stabilization

An approach to the control of elastic robotic systems for space applications using inversion, servocompensation, and feedback stabilization is presented. For simplicity, a robot arm (PUMA-type) with three rotational joints is considered. The third link is assumed to be elastic. Using an inversion algorithm, a nonlinear decoupling control law, u sub d, is derived such that in the closed loop system, independent control of joint angles by the three joint torquers is accomplished. For the stabilization of elastic oscillations, a linear feedback torquer control law, u sub s, is obtained applying linear quadratic optimization to the linearized arm model augmented with a servocompensator about the terminal state. Simulation results show that, in spite of uncertainties in the payload and vehicle angular velocity, good joint angle control and damping of elastic oscillations are obtained with the torquer control law u = u sub d + u sub s.

Singh, S. N.↗
NASA NTRS1984

Tradeoff methods in multiobjective insensitive design of airplane control systems

The latest results of an ongoing study of computer-aided design of airplane control systems are given. Constrained minimization algorithms are used, with the design objectives in the constraint vector. The concept of Pareto optimiality is briefly reviewed. It is shown how an experienced designer can use it to find designs which are well-balanced in all objectives. Then the problem of finding designs which are insensitive to uncertainty in system parameters are discussed, introducing a probabilistic vector definition of sensitivity which is consistent with the deterministic Pareto optimal problem. Insensitivity is important in any practical design, but it is particularly important in the design of feedback control systems, since it is considered to be the most important distinctive property of feedback control. Methods of tradeoff between deterministic and stochastic-insensitive (SI) design are described, and tradeoff design results are presented for the example of the a Shuttle lateral stability augmentation system. This example is used because careful studies have been made of the uncertainty in Shuttle aerodynamics. Finally, since accurate statistics of uncertain parameters are usually not available, the effects of crude statistical models on SI designs are examined.

Schy, A. A.↗
NASA NTRS1983

Tradeoff studies in multiobjective insensitive design of airplane control systems

A computer aided design method for multiobjective parameter-insensitive design of airplane control systems is described. Methods are presented for trading off nominal values of design objectives against sensitivities of the design objectives to parameter uncertainties, together with guidelines for designer utilization of the methods. The methods are illustrated by application to the design of a lateral stability augmentation system for two supersonic flight conditions of the Shuttle Orbiter. Objective functions are conventional handling quality measures and peak magnitudes of control deflections and rates. The uncertain parameters are assumed Gaussian, and numerical approximations of the stochastic behavior of the objectives are described. Results of applying the tradeoff methods to this example show that stochastic-insensitive designs are distinctly different from deterministic multiobjective designs. The main penalty for achieving significant decrease in sensitivity is decreased speed of response for the nominal system.

Schy, A. A.↗
NASA NTRS1981

Multiobjective insensitive design of airplane control systems with uncertain parameters

A multiobjective computer-aided design algorithm has been developed which minimizes the sensitivity of the design objectives to uncertainties in system parameters. The more important uncertain parameters are described by a gaussian random vector with known covariance matrix, and a vector sensitivity objective function is defined as the probabilities that the design objectives will violate specified requirements constraints. Control system parameters are found which minimize the sensitivity vector in a Pareto-optimal sense, using constrained minimization algorithms. Example results are shown for lateral stability augmentation system (SAS) design for three Shuttle flight conditions.

Schy, A. A.↗
NASA NTRS1980

Pseudosteady-state analysis of nonlinear aircraft maneuvers

An analytical method was developed for studying the combined effects of rotational coupling and nonlinear aerodynamics on aircraft response for specified control inputs. The method involves the simultaneous solution of two nonlinear equations which are functions of angle attack, roll rate, and control inputs. The method was applied to a number of maneuvers for a fighter-type aircraft. Time history responses verified the usefulness of the analysis for predicting a variety of response characteristics caused by interacting nonlinear aerodynamic and inertial effects, including spin conditions.

Young, J. W.↗
NASA NTRS1980

Output feedback non-linear decoupled control synthesis and observer design for manoeuvring aircraft

A study of the applicability of nonlinear decoupling theory to the design of control systems using output feedback for maneuvering aircraft is presented. The response variables chosen for decoupled control were angular velocity components along roll, pitch, and yaw axes, angle of attack (p), and angle of sideslip, using aileron, rudder, and elevator controls. An observer design for a class of nonlinear systems was presented and this method was used to estimate angle of attack and sideslip; an approximate observer was obtained by neglecting derivatives of p and aileron deflection angles and it was used in a simulation study. A simulation study showed that precise rapid combined lateral and longitudinal maneuvers can be performed; it was also demonstrated that a bank-angle-command outer loop could be designed for precise bank angles changes and simultaneous large lift maneuvers.

Singh, S. N.↗
NASA NTRS1980

Pseudosteady state analysis of nonlinear aircraft maneuvers

An analytical method has been developed for studying the combined effects of rotational coupling and nonlinear aerodynamics on aircraft response for specified control inputs. The method involves the simultaneous solution of two nonlinear equations which are functions of angle of attack, roll rate, and the control inputs. The method is applied to a number of maneuvers for a fighter type aircraft. Time history responses verified the usefulness of the analysis for predicting a variety of response characteristics caused by interacting nonlinear aerodynamic and inertial effects, including spin conditions.

Young, J. W.↗
NASA NTRS1980

Pareto-optimal multi-objective design of airplane control systems

A constrained minimization algorithm for the computer aided design of airplane control systems to meet many requirements over a set of flight conditions is generalized using the concept of Pareto-optimization. The new algorithm yields solutions on the boundary of the achievable domain in objective space in a single run, whereas the older method required a sequence of runs to approximate such a limiting solution. However, Pareto-optimality does not guarantee a satisfactory design, since such solutions may emphasize some objectives at the expense of others. The designer must still interact with the program to obtain a well-balanced set of objectives. Using the example of a fighter lateral stability augmentation system (SAS) design over five flight conditions, several effective techniques are developed for obtaining well-balanced Pareto-optimal solutions. For comparison, one of these techniques is also used in a recently developed algorithm of Kreisselmeier and Steinhauser, which replaces the hard constraints with soft constraints, using a special penalty function. It is shown that comparable results can be obtained.

Schy, A. A.↗
NASA NTRS1979

Nonlinear decoupled control synthesis for maneuvering aircraft

A control law for decoupling roll rate, angle of attack and sideslip in rapid, nonlinear airplane maneuvers is derived. For simplicity, only moments caused by ailerons, rudder and elevator are considered, and control forces are neglected. Simulated responses of the closed loop system, including the control forces, show that the neglected forces have no significant effects and that large, simultaneous lateral and longitudinal maneuvers can be precisely performed. The violent divergences which occur in open-loop maneuvers of this type are eliminated by the decoupling. The control law showed little sensitivity to 20 percent perturbation in three important stability derivatives.

Singh, S. N.↗
NASA NTRS1979

A multiple objective optimization approach to aircraft control systems design

The design of an aircraft lateral control system, subject to several performance criteria and constraints, is considered. While in the previous studies of the same model a single criterion optimization, with other performance requirements expressed as constraints, has been pursued, the current approach involves a multiple criteria optimization. In particular, a Pareto optimal solution is sought.

Tabak, D.↗
NASA NTRS1977

Prediction of jump phenomena in rotationally-coupled maneuvers of aircraft, including nonlinear aerodynamic effects

An analytical method has been developed for predicting critical control inputs for which nonlinear rotational coupling may cause sudden jumps in aircraft response. The analysis includes the effect of aerodynamics which are nonlinear in angle of attack. The method involves the simultaneous solution of two polynomials in roll rate, whose coefficients are functions of angle of attack and the control inputs. Results obtained using this procedure are compared with calculated time histories to verify the validity of the method for predicting jump-like instabilities.

Young, J. W.↗
NASA NTRS1976

Prediction of jump phenomena in roll-coupled maneuvers of airplanes

An easily computerized analytical method is developed for identifying critical airplane maneuvers in which nonlinear rotational coupling effects may cause sudden jumps in the response to pilot's control inputs. Fifth and ninth degree polynomials for predicting multiple pseudo-steady states of roll-coupled maneuvers are derived. The program calculates the pseudo-steady solutions and their stability. The occurrence of jump-like responses for several airplanes and a variety of maneuvers is shown to correlate well with the appearance of multiple stable solutions for critical control combinations. The analysis is extended to include aerodynamics nonlinear in angle of attack.

Schy, A. A.↗
NASA NTRS1974

Computer-aided design of control systems to meet many requirements

A method is described for using nonlinear programing in the computer-aided design of airplane control systems. It is assumed that the quality of such systems depends on many criteria. These criteria are included in the constraints vector (instead of attempting to combine them into a single scalar criterion, as is usually done), and the design proceeds through a sequence of nonlinear programing solutions in which the designer varies the specification of sets of requirements levels. The method is applied to design of a lateral stability augmentation system (SAS) for a fighter airplane, in which the requirements vector is chosen from the official handling qualities specifications. Results are shown for several simple SAS configurations designed to obtain desirable handling qualities over all design flight conditions with minimum feedback gains. The choice of the final design for each case is not unique but depends on the designer's decision as to which achievable set of requirements levels represents the best for that system. Results indicate that it may be possible to design constant parameter SAS which can satisfy the most stringent handling qualities requirements for fighter airplanes in all flight conditions. The role of the designer as a decision maker, interacting with the computer program, is discussed. Advantages of this type of designer-computer interaction are emphasized. Desirable extensions of the method are indicated.

Schy, A. A.↗
NASA NTRS1972

Nonlinear programming in design of control systems with specified handling qualities.

A method is described for using nonlinear programing in the computer-aided design of aircraft control systems. It is assumed that the quality of such systems depends on many criteria. These criteria are included in the constraints vector, and the design proceeds through a sequence of nonlinear programing solutions in which the designer varies the specification of sets of requirements levels. The method is applied to design of a lateral stability augmentation system (SAS) for a fighter aircraft, in which the requirements vector is chosen from the official handling-qualities specifications. Results are shown for several simple SAS configurations designed to obtain desirable handling qualities over all design flight conditions with minimum feedback gains.

Schy, A. A.↗