Engineering topics

Scipioni, Roberto

Publications and source records attributed to Scipioni, Roberto.

5 records

DOE OSTI2023

Beneficial Effects of La 0.5 Sr 0.5 CoO 3 Coatings on Thin‐Film LiMn 2 O 4 Cathodes for Lithium Ion Batteries

Abstract The severe capacity loss of spinel LiMn 2 O 4 (LMO) limits the utility of this otherwise promising lithium ion battery cathode material. One of the strategies to mitigate capacity fade is applying a coating on LMO particle surfaces. While this approach yields promising results, there is limited understanding of mechanisms whereby coatings improve LMO capacity retention. Herein, the effects of a new protective coating material, La 0.5 Sr 0.5 CoO 3 (LSCO), in a thin‐film battery geometry that is amenable to fundamental studies of electrode processes, are reported. RF sputtering deposition is used to produce high quality 25–100 nm LMO cathodes on Al 2 O 3 substrates with an intervening Pt/Ti back‐side contact layer. Cycling of the un‐coated cathodes results in capacity loss of 18% over 300 cycles. Adding a 2 nm LSCO layer reduces the capacity loss to 3%. While this may be due in part to reduced Mn dissolution, scanning transmission electron microscopy results indicate that the coating helps to preserve crystallinity and reduce lattice structure distortion due to inhibited formation of defect tetragonal spinel. Three‐electrode electrochemical impedance spectroscopy results reveal that the LSCO coating increases charge transfer and ohmic resistances, but the increases are generally too small to significantly impact cell performance even at high C‐rates.

25 ENERGY STORAGE↗

DOE OSTI2020

Sm 0.5 Sr 0.5 CoO 3-δ Surface Modification of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ -Ce 0.9 Gd0.1 2-δ Composite Oxygen Electrodes for Solid Oxide Electrochemical Cells

La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3- δ -Ce 0.9 Gd 0.1 O 2- δ (LSCF-GDC) composite oxygen electrodes have been widely used in intermediate temperature (<700 °C) solid oxide cells, with composite usually providing better electrochemical performance than single-phase LSCF. However, LSCF-based electrodes are often observed to degrade over time due to Sr segregation. Here we present an impedance spectroscopy study comparing the degradation behaviors of LSCF-GDC and Sm 0.5 Sr 0.5 CoO 3- δ (SSC) infiltrated LSCF-GDC electrodes. The LSCF-GDC polarization resistance increases by ~5 times over ~1000 h at 650 °C. In contrast, the SSC-infiltrated electrode shows similar initial polarization resistance but much more stable performance. The impedance modeling results show that the improved stability is associated with the low frequency oxygen dissociative adsorption/desorption process. The results suggest that this adsorption/desorption process slows due to increased Sr segregation on LSCF over time, and that SSC does not degrade significantly due to Sr surface segregation.

Electrochemistry↗

DOE OSTI2020

Tuning electrochemical and transport processes to achieve extreme performance and efficiency in solid oxide cells

Solid oxide cells (SOCs) have important applications as fuel cells and electrolyzers. The application for storage of renewable electricity is also becoming increasingly relevant; however, it is difficult to meet stringent area-specific resistance (ASR) and long-term stability targets needed to achieve required efficiency and cost. Here we show a new SOC that utilizes a very thin Gd-doped ceria (GDC)/yttria-stabilized zirconia (YSZ) bi-layer electrolyte, Ni–YSZ cell support with enhanced porosity, and electrode surface modification using PrO x and GDC nanocatalysts to achieve unprecedented low ASR values < 0.1 Ω cm 2 , fuel cell power density ~3 W cm –2 , and electrolysis current density ~4 A cm –2 at 800 °C. Besides this exceptionally high performance, fuel cell and electrolysis life tests suggest very promising stability in fuel cell and steam electrolysis modes. Furthermore, electrochemical impedance spectroscopy analysis done using a novel impedance subtraction method shows how rate-limiting electrode processes are impacted by the new SOC materials and design.

25 ENERGY STORAGE↗

DOE OSTI2020

A silicate dynamo in the early Earth

The Earth’s magnetic field has operated for at least 3.4 billion years, yet how the ancient field was produced is still unknown. The core in the early Earth was surrounded by a molten silicate layer, a basal magma ocean that may have survived for more than one billion years. Here we use density functional theory-based molecular dynamics simulations to predict the electrical conductivity of silicate liquid at the conditions of the basal magma ocean: 100–140 GPa, and 4000–6000 K. We find that the electrical conductivity exceeds 10,000 S/m, more than 100 times that measured in silicate liquids at low pressure and temperature. The magnetic Reynolds number computed from our results exceeds the threshold for dynamo activity and the magnetic field strength is similar to that observed in the Archean paleomagnetic record. We therefore conclude that the Archean field was produced by the basal magma ocean.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Enhancement of Ni–(Y 2 O 3 ) 0.08 (ZrO 2 ) 0.92 fuel electrode performance by infiltration of Ce 0.8 Gd 0.2 O 2–δ nanoparticles

This paper addresses the use of Ce 0.8 Gd 0.2 O 2–δ (GDC) infiltration into the Ni–(Y 2 O 3 ) 0.08 (ZrO 2 ) 0.92 (YSZ) fuel electrode of solid oxide cells (SOCs) for improving their electrochemical performance in fuel cell and electrolysis operation. Although doped ceria infiltration into Ni–YSZ has recently been shown to improve the electrode performance and stability, the mechanisms defining how GDC impacts electrochemical characteristics are not fully delineated. Furthermore, the electrochemical characteristics have not yet been determined over the full range of conditions normally encountered in fuel cell and electrolysis operation. Here we present a study of both symmetric and full cells aimed at understanding the electrochemical mechanisms of GDC-modified Ni–YSZ over a wide range of fuel compositions and temperatures. Single-step GDC infiltration at an appropriate loading substantially reduced the polarization resistance of Ni–YSZ electrodes in electrolyte-supported cells, as measured using electrochemical impedance spectroscopy (EIS) at various temperatures (600–800 °C) in a range of H 2 O–H 2 mixtures (3–90 vol% H 2 O). Fuel-electrode-supported cells had significant concentration polarization due to the thick Ni–YSZ supports. Here, a distribution of relaxation times approach is used to develop a physically-based electrochemical model; the results show that GDC reduces the reaction resistance associated with three-phase boundaries, but also appears to improve oxygen transport in the electrode. Increasing the H 2 O fraction in the H 2 –H 2 O fuel mixture reduced both the three-phase boundary resistance and the gas diffusion resistance for Ni–YSZ; with GDC infiltration, the electrode resistance showed less variation with fuel composition. GDC infiltration improved the performance of fuel-electrode-supported full cells, which yielded a maximum power density of 2.28 W cm –2 in fuel cell mode and an electrolysis current density at 1.3 V of 2.22 A cm –2 , both at 800°C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗