Engineering topics

Scott A. Berry

Publications and source records attributed to Scott A. Berry.

5 records

NASA NTRS2023

Experimental Aeroheating Study in NASA LaRC 20-Inch Mach 6 Air Tunnel: Discrete Roughness on BOLT – Test 7071

An experimental study of the effect of discrete roughness (trips) on boundary layer transition was conducted in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel on the BOLT shape. This study was intended to obtain results that could eventually be compared against experimental results from other facilities, as well as from flight. The trip locations for the present study were selected to correspond to those used for the flight vehicle, but the heights of these discrete roughness elements were varied. Infrared thermography was used to obtain images of the effect of these trips on the behavior of the boundary layer. This report is intended as a quick release of experimental results.

hypersonic↗

NASA NTRSDate not supplied

Development of the BOLT II Roughness Experiment for Flight

BOLT II is a sounding rocket research project with the goal of studying hypersonic boundary layer transition and turbulence. The BOLT II research vehicle is based on a three-dimensional geometry (a slightly longer version of BOLT) with concave surfaces and swept leading edges that provides two separate and distinct, also redundant, flow paths for conducting measurements. One side of BOLT II is dedicated to smooth surface transition and turbulence, to better study the natural instability processes, while the other has been assigned to study forced transition and turbulence using discrete roughness trips. The present paper is intended to document the primary drivers and decisions made leading up to finalizing the roughness side experiment for the BOLT II flight.

hypersonic↗

NASA NTRSDate not supplied

BOLT II Roughness-Side Flight Results

An initial review of the roughness data from the BOLT II flight is provided. The BOLT II roughness experiment was designed to investigate discrete trips in flight based on the diamond configuration, which has been shown to be an efficient vortex generator and boundary layer trip from extensive ground-based testing. There were three trip locations chosen for the flight test and their size (height and width) were tailored to the local boundary layer thickness, but all three were expected to trip at the same time or flight condition. Details about the flight vehicle design, instrumentation, and best estimated trajectory are discussed. The present paper is limited to only a review and analysis of the thermocouple data. Boundary layer transition onset times are derived from the thermocouple analysis, thus allowing an initial assessment of the performance of these discrete trips. Since the three trips were sized to trip the boundary layer at the same time, based on a previous wind tunnel study, the present analysis indicates that they performed as expected.

Hypersonic↗

NASA NTRSDate not supplied

Recent BOLT Discrete-Roughness Trip Results from the 20-Inch Mach 6 Tunnel

- Air Force Office of Scientific Research (AFOSR) primary sponsor of BOLT (for Boundary Layer Transition) sounding rocket flight project as continuation of previous HIFiRE flights (1 & 5) - Sounding rockets provide cost-effective flight research tool - Study hypersonic BoLT on increasingly complex geometries - BOLT shape includes concave surfaces and swept leading edges - Two missions, two flights: - BOLT mission at Esrange, Sweden - Johns Hopkins University Applied Physics Laboratory as lead - Focus on transition onset measurements - Flew June 2021 (staging anomaly) - BOLT II mission at Wallops Flight Facility, Virginia - Texas A&M and CUBRC provide primary leadership - Focus on turbulence measurements - Flew March 2022 - Flight named in memory of Mike Holden - NASA’s support to both BOLT missions provided through the Hypersonic Technologies Project (HTP)

Hypersonic↗

NASA NTRSDate not supplied

A Preliminary Assessment of Step Effects on the BOLT Geometry in Mach 6 Flow

An infrared thermography measurement technique has been installed in the Langley Aerothermodynamic Laboratory. The system is calibrated for use with commercially available thermoplastics and ceramic materials, and to the surface temperature ranges when exposed to the facility hypersonic flow. Herein an uncertainty quantification is performed, revealing 5% surface temperature and 20% heat transfer uncertainty bands to two-sigma confidence. As a first application of the test measurement technique, an investigation was conducted to explore the correlation between the height of forward facing (FF) and rearward facing (RF) two-dimensional steps, free stream Reynolds number, and the onset of boundary layer transition from laminar to turbulent in Mach 6 flow on a 50% scale Boundary Layer Transition (BOLT) flight test vehicle geometry. Computational predictions were generated to identify potential x/L locations of transition onset for various flow conditions with a smooth outer mold line geometry and are compared to experimental results. The BOLT Step Test was conducted in the NASA Langley Aerothermodynamic Laboratory 20-inch Mach 6 wind tunnel at Reynolds numbers between 1.4 and 11.3 million conditions for various step heights. Data were collected using a developmental infrared thermography test technique and reduced to heat transfer for comparison with CFD solutions. This is a preliminary assessment of the developmental infrared thermography test technique used to acquire and reduce the experimental data. insight into the ongoing comparative analysis of the effects of FF and RF steps on boundary layer transition for the BOLT geometry in Mach 6 flow.

BOLT↗