Nd3+→ Cr4+ energy transfer in co-doped Nd,Cr:Y3Al5O12 garnet transparent ceramics
Not Available
Phillips, Ian R. (ORCID:000000015067786X)↗
Engineering topics
Seeley, Zachary M.
Publications and source records attributed to Seeley, Zachary M..
Silicon Photomultipliers Coupled to Scintillators With the Emission Maximum at 550 nm
A majority of the silicon photomultipliers (SiPMs) are sensitive to blue and near-ultraviolet (NUV) photons that are not optimized for scintillators with the emission maximum at wavelengths longer than 500 nm. The red–green–blue (RGB) SiPM is developed for the maximum photon detection efficiency (PDE) at 550 nm, which is a good match for some high-light-yield scintillators, such as CsI:Tl (CsI) and Gd 1.5 Y 1.5 Ga 2 Al 3 O 12 :Ce (GYGAG). Comparisons are made for the performance of these scintillators coupled to the RGB SiPM and a blue-sensitive SiPM. Because it takes tens of nanoseconds for the microcells to recharge after registering a photon hit, the linearity of these scintillation detectors was studied for high-energy gammas where numerous scintillation photons are generated. In addition, the energy resolution of the 662-keV gamma emitted by 137 Cs was measured for temperatures between –20 °C and 50 °C. The nonlinearity was observed above 1 MeV for all measurements, and however, it can be corrected by energy calibration using a third-degree polynomial. For CsI, the energy resolution is better with the blue-sensitive SiPM because of the lower dark count rate (DCR). In contrast, GYGAG coupled to the RGB SiPM has a better energy resolution for temperatures below 30 °C because of the well-matched emission spectrum and PDE distribution. Nevertheless, the advantage disappears for temperatures above 30 °C due to the higher DCR. It would be useful to further develop the RGB SiPM with a lower DCR and higher operating temperatures.
42 ENGINEERING↗
($\mathrm{INVITED}$)Counter-ion effect on the diffusion behavior of $\mathrm{Y}$b, $\mathrm{L}$u, and $\mathrm{N}$d ions in $\mathrm{YAG}$ transparent ceramics
The ability to fabricate additively manufactured laser waveguides with sharp dopant concentration interfaces is limited by diffusion of the dopants at the temperatures required to fully densify the material. Compositional analysis of bilayer samples, where each layer was either undoped YAG or YAG doped with Yb, Lu, or Nd, were fabricated such that all combinations were available for testing. Samples were fabricated at both 1750°C and 1850°C to determine the diffusion behavior of each dopant alone and also in the presence of a second dopant. It was found that the experimental concentration profiles exhibited both intragranular (bulk) and grain boundary contributions, and thus fitting to a complementary error function equation required the use of two diffusion coefficients. Nd always diffused further along grain boundaries than the other dopants, due in part to its small segregation coefficient in YAG. It is shown that the presence of Nd as a counter dopant inhibits intragranular diffusion of other dopants while enhancing their grain boundary diffusion. All the observed trends were attributed to a combination of intragranular lattice strain due to: dopant ions replacing yttrium substitutionally, the relative driving forces for the segregation of dopant ions to grain boundaries, and the ability of one dopant to affect the diffusion of a different dopant in the other direction to maintain charge neutrality.
36 MATERIALS SCIENCE↗
Material jet printing of transparent ceramic Yb:YAG planar waveguides
A new, to the best of our knowledge, 3D additive manufacturing technique utilizing particle-loaded ink jet printing to fabricate transparent ceramic Yb:YAG planar waveguides for laser gain media was demonstrated. Rheological optimization of YAG particle-loaded inks resulted in successful droplet formation and printing resolution. Planar waveguides composed of a Yb:YAG guide encased in undoped YAG cladding were printed with guide thicknesses ranging between 25 and 350 µm and consolidated to high optical quality via solid-state sintering. Sufficiently low optical (1–3%/cm) and intermodal scatter allowed single-mode propagation with a core/clad index difference of Δ<!-- Δ --> n ∼<!-- ~ --> 5.0 ×<!-- × --> 10 −<!-- - --> 4 (corresponding to 3 at.% Yb). The waveguides were cladding-pumped longitudinally with a 940 nm diode array resulting in 23.6% slope efficiency in 2 ms pulsed operation.
36 MATERIALS SCIENCE↗
Laser gain media fabricated via direct ink writing (DIW) and ceramic processing
A transparent ceramic optic includes: a lasing region comprising at least one lasing species dopant; and a transparent region transparent to light generated by the lasing species. At least the transparent region is doped with at least one other dopant species such that the lasing region and the transparent region are characterized by a difference in refractive index between the two regions in an amount of about 1.0×10−4 or less. Inventive formulations of inks suitable for fabricating transparent ceramic optics having desirable compositional characteristics such as concentration gradients in desired spatial arrangements, e.g. using additive manufacturing techniques such as direct ink writing and/or extrusion freeform fabrication are also disclosed, along with suitable techniques for forming the transparent ceramic optics from such inks.
Payne, Stephen A.↗