Search NASA⌕ Search

Engineering topics

Seibert, Rachel

Publications and source records attributed to Seibert, Rachel.

At least 19 records

Characterization of the radial microstructural evolution in LWR UO 2 using electron backscatter diffraction

Studies on high burnup UO 2 subjected to loss-of-coolant accident conditions have shown that restructured regions of the fuel are susceptible to pulverization and eventual dispersal. Due to a lack of pre-test characterization, the distinct microstructural features rendering the fuel prone to fragmentation remain ambiguous. Four samples of commercially irradiated light-water reactor UO 2 have been characterized utilizing electron backscatter diffraction to assess the susceptible microstructure. The microscopy focused on determining the burnup and temperature conditions responsible for the formation of the different microstructural regions where the regions were denoted as the high-burnup structure (HBS), HBS transition, mid-radial, restructured central, and central region. Previous works have outlined the specific conditions required for the restructuring of the microstructure into the HBS, but the conditions responsible for the restructuring in the central region of the fuel are not well understood. The four analyzed samples confirm a burnup threshold of 61 GWd/tU, and an unknown temperature range is needed to facilitate the formation of the restructured central region. In conclusion, additional fuel performance evaluations are needed to quantify the temperature range promoting restructuring in the central region.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Accelerated fission rate irradiation design, pre-irradiation characterization, and adaptation of conventional PIE methods for U-10Mo and U-17Mo

Metallic U alloys have high U density and thermal conductivity and thus have been explored since the beginning of nuclear power research. Alloys of U with modest amounts of Mo, such as U-10 wt % Mo (U-10Mo), are of particular interest because the γ-U crystal structure in this alloying addition shows prolonged stability in reactor service. Historically, radiation data on U-10Mo fuels were collected in Na fast reactors or lower temperature research reactor conditions, but little is known about irradiation behavior, particularly swelling and creep, at irradiation temperatures between 250 and 500°C. This work discusses the methodology and pre-irradiation characterization results from a U-Mo irradiation campaign performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. U-10Mo and U-17Mo samples irradiations are being completed at temperatures ranging from 250 to 500°C to three targeted fission densities between 2 × 10 20 and 1.5 × 10 21 fissions per cubic centimeter. Swelling measurement of the specimen sizes studied here required development and assessment of new methods for volume determination before and after irradiation. Laser profilometry and X-ray computation tomography (XCT) were used to provide preirradiation characterization of samples to determine the error and applicability of each to determine swelling following irradiation. These outcomes are contextualized through use of BISON simulations performed to assess the predicted expansion of U-Mo fuels subjected to the irradiation conditions of this work. Use of existing BISON fuel performance models predicted a maximum of 7% swelling under the irradiation conditions of this study. Pre-irradiation characterization revealed the as-cast U-Mo fuel samples were uniformly large-grained fully cubic U crystals with small U-C/N bearing precipitates and pores distributed throughout. Samples were found to contain a bulk porosity between .4 and 3% because of the casting process. Local porosity in areas far from large, interconnected pores was found by Slice-and-View to be under .2%. Nanometer-sized precipitates rich in C and N were identified in all samples, likely because of impurities during the fabrication process. Dendritic bands were also observed throughout the samples. These bands were characterized by variable Mo content that deviated from the overall Mo content by 2–3 wt %. No other microstructural features were correlated to these bands. Mechanical properties were found to be slightly strengthened compared to literature reports of bulk U-Mo fuels due to the nano-scale precipitates throughout the sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Microscopy for Characterization of High Burnup Commercial UO 2 Fuel Before and After LOCA Testing

This report presents the results from the microstructural examination of high burnup UO 2 under pre- and post- loss of coolant accident (LOCA) conditions. The work in this report builds and expands upon work previously conducted on high burnup UO 2 fuel at Oak Ridge National Laboratory (ORNL). This work investigates the microstructural evolution that occurs during steady state irradiation of UO 2 , particularly in high burnup fuel. Several high burnup fuel samples were available from historic fuel shipments to ORNL. Microstructural characterization will aid in understanding why the fuel is susceptible to fuel fragmentation and support future work to investigate the formation mechanisms of certain features that form under irradiation. High burnup UO 2 microstructural data is also needed to improve constitutive models intended to predict high burnup fuel fragmentation (HBFF). This report summarizes the microstructural evaluation of these fuel samples to interpret and analyze high burnup fuel microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Temperature Effect of Gas Bubble Evolution in UCN Fuel Kernels Irradiated by Swift Xe Ions

UC1-xNx fuel kernels provided by Oak Ridge National Laboratory (ORNL) were irradiated by 84 MeV Xe ions at two different temperatures (450°C & 750°C) at the Argonne Tandem Linac Accelerator System (ATLAS) at Argonne National Laboratory, followed by post-irradiation examination. The primary goal of this study was to understand gas bubble formation (due to accumulation of Xe gas) and corresponding size evolution dependent upon net Xe deposition at the two different temperatures. From the post-irradiation examinations of the samples, it can be concluded at 750°C, with same amount of dose received, the Xe gas bubbles seems to coarsen much more easily compared to 450°C. The results generated for fission gas bubble evolution observed in this study can be used to support fuel performance models for UC1-xNx fuel kernels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Selection and Characterization of Surrogate Material for Developing Zr Barrier Coatings for Uranium Nitride Particles

In support of UC 1-x N x fuel kernels (~ 800 micrometer diameter) development work ongoing at Oak Ridge national laboratory (ORNL), where the fuel kernels will be embedded inside a possible zirconium based matrix, Argonne National Laboratory (ANL) is contributing to help develop a robust metal diffusion barrier coating. Zirconium nitride (ZrN) and Zirconium oxide (ZrO2) were selected as possible diffusion barrier candidates, and the atomic layer deposition (ALD) has been chosen as a candidate technology to deposit the film. Development of such a barrier coating with the ALD process entails significant number of trials to study relevant parameters. Therefore, to prevent needless wastage, instead of coating directly over fuel kernels, a surrogate candidate with similar dimensions and physical properties were been selected and coated to develop the diffusion barrier coating.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary results from Low Pressure Steam Oxidation Testing of ALD ZrN and ZrO2 Coating Deposited over UCN Fuel Kernels

Steam oxidation testing was used to investigate as-developed 100 nm ALD ZrN and 1000 nm ZrO 2 coatings deposited over UC1-xNx fuel kernels. The results of these tests were compared against oxidation of uncoated kernels. This work was performed to support development of coatings which both provide high temperature Zr metal diffusion barrier and also provide resistance against oxidation, especially against high temperature steam and/or air. This work was performed in collaboration with Oak Ridge National Laboratory (ORNL), using ORNL-provided samples. The oxidation tests yielded valuable information, including relative differences in performance of different coating materials and coating thicknesses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication of UN-Mo CERMET Nuclear Fuel Using Advanced Manufacturing Techniques

Ceramic-metallic nuclear fuels are a candidate fuel for nuclear thermal propulsion systems due to their high heat transport properties, which are necessary in very high-temperature environments. The conventional fabrication of uranium nitride–molybdenum fuel has been thoroughly studied in the past, but modern manufacturing techniques have presented a unique opportunity for further development within this field. This work demonstrates the use of advanced manufacturing techniques to produce nuclear fuel pellets composed of uranium nitride microspheres encased in a molybdenum matrix. Binder jetting is used to print molybdenum disks that are filled with uranium nitride microspheres and afterward sintered using spark plasma sintering. Two fuel pellets were fabricated to demonstrate the methodology and to provide a baseline analysis of the effects of temperature and pressure processing conditions. Characterization of the sintered fuel pellets includes detailed microstructural analysis and thermal conductivity measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Redistribution of radionuclides in irradiated AGR-1 UCO TRISO fuel after 1800 °C safety testing

Release of radionuclides from intact tristructural-isotropic (TRISO) coated particle fuel at normal and accident conditions is a primary metric of fuel performance. The distribution of fission products and actinides in the TRISO layers of individual particles provides insight on radionuclide transport and release behavior and was determined using scanning electron microscopy analysis. Particles were isolated from an irradiated fuel compact (AGR-1 Compact 4-4-2) and analyzed as-irradiated or after individual particle safety-testing at 1800 °C for 650 h. Particles were selected for comparison based on their remaining 110mAg fission product inventory. These comparisons corroborated the observation that the 110m Ag inventory is a marker for relative irradiation temperature based on observed radionuclide distribution in the SiC layer. The comparison also indicated that the in-pile behavior influences the fission product and actinide species interactions with the TRISO layers during high temperature exposure after irradiation. The analysis confirms both palladium and uranium diffusion, as well as other species, are active in the UCO TRISO fuel system at 1800 °C and that palladium transport is active at lower temperatures relative to uranium. While diffusion across the SiC layer was observed, the intact nature of the SiC layer after the 1800 °C, 650-h exposure indicates the SiC layer maintained its functionality as a fission product barrier by mitigating release of radionuclides at beyond accident margin temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Role of microstructure on CO corrosion of SiC layer in UO₂-TRISO fuel

The Advanced Gas Reactor Fuel Qualification and Development (AGR) program has focused on qualification of UCO kernel tristructural-isotropic (TRISO) particle fuel relative to UO₂ kernel TRISO particle fuel. However, a UO₂ kernel variant was included in the second AGR irradiation experiment (AGR-2) for comparison and to connect to historic fuel irradiation data. The development of a multiscale, post-irradiation examination (PIE) analysis approach through the AGR Program has allowed for a comprehensive understanding of individual particle failure. This approach has been applied to gain an understanding of SiC layer failure in UO₂ kernel TRISO fuel from AGR-2 after safety testing at 1600–1700 °C. Particle failure by intergranular CO corrosion, facilitated by a compromised inner pyrolytic carbon layer, has been confirmed through the combined application of modern x-ray computed tomography and electron microscopy techniques. In addition, a relationship between grain boundary character and CO corrosion has been identified. This finding provides an opportunity to develop mitigating strategies to improve the resilience of the SiC layer to CO corrosion in UO₂ TRISO fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Three-dimensional bubble reconstruction in high burnup UO 2

In light water reactor (LWR) UO 2 fuels, the evolution of volatile fission products is one of the critical areas of fuel behavior that is yet to be fully understood. In UO 2 irradiated to high burnups, it is well known that most released fission gases come from the central region of the fuel as opposed to the highly porous high burnup structure (HBS) on the periphery of the pellets. However, fuels with and without interconnected bubble networks at the fuel center showed high to moderate release fractions, which conceals the mechanisms responsible for the gas release in the latter scenario. In this work, focused ion beam tomography was used to investigate the three-dimensional bubble structure in an irradiated LWR UO 2 fuel pellet with high degree of fission gas retention so that the degree of bubble interconnection could be assessed. Six radial locations with different burnups and temperatures were serially sectioned and imaged to reconstruct the three-dimensional bubble structure. As expected, the highest porosity was observed at the periphery of the fuel (HBS). Here, the porosity then decreased towards the pellet center, except for the centermost location. This location had a slightly higher porosity than its adjacent mid-radial location, which was attributed to the temperature difference between the two locations. This study provides a first-time volumetric evaluation of the porosity at different radial locations on a UO 2 fuel pellet. During this investigation, no significant bubble interconnection was noted at any of the six radial locations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress on Synthesis of Low Content Inert Matrix Fuel Pellets

Progress was made on optimizing hot-press parameters for preparing fuel for two different coating methods: chemical vapor deposition (CVD) and chemical vapor infiltration (CVI). Surrogate materials, CeO 2 and ZrO 2 , were used in place of UO 2 and PuO 2 for fuel development. Although the more porous CeO 2 pellets were not successfully made to the extent that CVI would work with them as intended, hot-press parameters were optimized such that the pellets could be coated using CVD. The ZrO 2 was denser and therefore could more successfully be pressed to CVI standards; however, further improvement is needed before the process is implemented. Future work will continue to explore the optimization of a porous structure for CVI.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FY18Q4 Quarterly Report: Radiation Enhanced Diffusion of Ag, Ag-Pd, Eu, and Sr in Neutron Irradiated PyC/SiC Diffusion Couples

An improved understanding of the diffusion of select fission product systems in materials representative of tristructural-isotopic (TRISO) coated particle fuel are being sought to improve the safety and efficiency of high temperature gas-cooled reactors. Novel diffusion couple samples have been produced to explore diffusion under neutron irradiation and at temperatures representative of safety testing conditions. An update on the status of the neutron irradiation study and high temperature thermal testing is discussed which build upon prior reporting

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preparation of Diffusion Couples for Irradiation and High Temperature Testing of Representative TRISO PyC/SiC

Understanding the release of fission products from intact tristructural-isotropic (TRISO) coated particle fuel during normal and off-normal service is necessary to ensuring safe and efficient reactor operation. Planar diffusion couples have been fabricated to determine the diffusion kinetics of select fission product species (Ag, Ag+Pd, Eu, and Sr) in pyrocarbon (PyC) and silicon carbide (SiC) materials which are representative of TRISO fuel. Obtaining accurate diffusion coefficients for these systems in representative materials will allow for higher fidelity inputs for fuel performance models. Three different diffusion couple variants have been produced which include a Baseline, PyC, and SiC variant. The Baseline variant serves as an example of representative PyC and SiC layers as the layer properties mimic those found in TRISO fuel from the second Advanced Gas Reactor Fuel Qualification and Development Program. The PyC and SiC variants include variation in the respective layer properties to understand the impact of PyC density and SiC grain size on fission product diffusion. The diffusion couples were designed to allow for exploration of neutron irradiation on diffusion reflecting in reactor behavior as well as high temperature thermal diffusion reflecting diffusive transport during off-normal conditions. The methodology for selecting the diffusion couple design, refinement of the individual variant layer properties, and the complete process for diffusion couple construction are summarized in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Structure, Chemistry, and Charge Transfer Resistance of the Interface between Li 7 La 3 Zr 2 O 12 Electrolyte and LiCoO 2 Cathode

All-solid-state batteries promise significant safety and energy density advantages over liquid-electrolyte batteries. The interface between the cathode and the solid electrolyte is an important contributor to charge transfer resistance. Strong bonding of solid oxide electrolytes and cathodes requires sintering at elevated temperatures. Knowledge of the temperature dependence of the composition and charge transfer properties of this interface is important for determining the ideal sintering conditions. To understand the interfacial decomposition processes and their onset temperatures, model systems of LiCoO 2 (LCO) thin films deposited on cubic Al-doped Li 7 La 3 Zr 2 O 12 (LLZO) pellets were studied as a function of temperature using interface-sensitive techniques. X-ray photoelectron spectroscopy, secondary ion mass spectroscopy, and energy-dispersive X-ray spectroscopy data indicated significant cation interdiffusion and structural changes starting at temperatures as low as 300 °C. La 2 Zr 2 O 7 and Li 2 CO 3 were identified as decomposition products after annealing at 500 °C by synchrotron X-ray diffraction. X-ray absorption spectroscopy results indicate the presence of also LaCoO 3 in addition to La 2 Zr 2 O 7 and Li 2 CO 3 . On the basis of electrochemical impedance spectroscopy and depth profiling of the Li distribution upon potentiostatic hold experiments on symmetric LCO|LLZO|LCO cells, the interfaces exhibited significantly increased impedance, up to 8 times that of the as-deposited samples after annealing at 500 °C. Here, our results indicate that lower-temperature processing conditions, shorter annealing time scales, and CO 2 -free environments are desirable for obtaining ceramic cathode|electrolyte interfaces that enable fast Li transfer and high capacity.

25 ENERGY STORAGE↗