Engineering topics

Seiner, John M.

Publications and source records attributed to Seiner, John M..

At least 19 records

NASA NTRS2000

Undulated Nozzle for Enhanced Exit Area Mixing

A nozzle having an undulating surface for enhancing the mixing of a primary flow with a secondary flow or ambient air, without requiring an ejector. The nozzle includes a nozzle structure and design for introducing counter-rotating vorticity into the primary flow either through (i) internal surface corrugations where an axisymmetric line through each corrugation is coincident with an axisymmetric line through the center of the flow passageway or (ii) through one or more sets of alternating convexities and cavities in the internal surface of the nozzle where an axisymmetric line through each convexity and cavity is coincident with an axisymmetric line through the center of the flow passageway, and where the convexities contract from the entrance end towards the exit end. Exit area mixing is also enhanced by one or more chevrons attached to the exit edge of the nozzle. The nozzle is ideally suited for application as a jet engine nozzle. When used as a jet engine nozzle, noise suppression with simultaneous thrust augmentation/minimal thrust loss is achieved.

Seiner, John M.↗

NASA NTRS1999

Application Focused Schlieren to Nozzle Ejector Flowfields

The motivation of the testing was to reduce noise generated by eddy Mach wave emission via enhanced mixing in the jet plume. This was to be accomplished through the use of an ejector shroud, which would bring in cooler ambient fluid to mix with the hotter jet flow. In addition, the contour of the mixer, with its chutes and lobes, would accentuate the merging of the outer and inner flows. The objective of the focused schlieren work was to characterize the mixing performance inside of the ejector. Using flow visualization allowed this to be accomplished in a non-intrusive manner.

Mitchell, L. Kerry↗

NASA NTRS1999

Prediction, Measurement, and Suppression of High Temperature Supersonic Jet Noise

The photograph in figure 1 displays a water cooled round convergent-divergent supersonic nozzle operating slightly overexpanded near 2460 F. The nozzle is designed to produce shock free flow near this temperature at Mach 2. The exit diameter of this nozzle is 3.5 inches. This nozzle is used in the present study to establish properties of the sound field associated with high temperature supersonic jets operating fully pressure balanced (i.e. shock free) and to evaluate capability of the compressible Rayleigh model to account for principle physical features of the observed sound emission. The experiment is conducted statically (i.e. M(sub f) = 0.) in the NASA/LaRC Jet Noise Laboratory. Both aerodynamic and acoustic measurements are obtained in this study along with numerical plume simulation and theoretical prediction of jet noise. Detailed results from this study are reported previously by Seiner, Ponton, Jansen, and Lagen.

Seiner, John M.↗

NASA NTRS1999

Jet Nozzle Having Centerbody for Enhanced Exit Area Mixing

A nozzle arrangement includes a nozzle and a centerbody. The longitudinal axis of the centerbody is coaxially aligned with the nozzle. The centerbody has a free end portion shaped to create vortices in exhaust exiting the exit area. The vortices enhance mixing action in the exhaust and reduce exhaust noise while augmenting thrust.

Seiner, John M.↗

NASA NTRS1998

Screws, Propellers and Fans Based on a Mobius Strip

A Mobius strip concept is intended for improving the working efficiency of propellers and screws. Applications involve cooling, boat propellers, mixing in appliance, blenders, and helicopters. Several Mobius shaped screws for the average size kitchen mixers have been made and tested. The tests have shown that the mixer with the Mobius shaped screw pair is most efficient, and saves more than 30% of the electric power by comparison with the standard. The created video film about these tests illustrates efficiency of Mobius shaped screws.

Seiner, John M.↗

NASA NTRS1998

Mixing Enhancement by Tabs in Round Supersonic Jets

The objective of this study was to analyze jet plume mass flow entrainment rates associated with the introduction of counter-rotating streamwise vorticity by prism shaped devices (tabs) located at the lip of the nozzle. We have examined the resulting mixing process through coordinated experimental tests and numerical simulations of the supersonic flow from a model axisymmetric nozzle. In the numerical simulations, the total induced vorticity was held constant while varying the distribution of counter-rotating vorticity around the nozzle lip training edge. In the experiment, the number of tabs applied was varied while holding the total projected area constant. Evaluations were also conducted on initial vortex strength. The results of this work show that the initial growth rate of the jet shear layer is increasingly enhanced as more tabs are added, but that the lowest tab count results in the largest entrained mass flow. The numerical simulations confirm these results.

Seiner, John M.↗

NASA NTRS1997

Near Field Pressure Fluctuations in the Exit Plane of a Choked Axisymmetric Nozzle

Nearfield pressure data are presented for an unheated jet issuing from an underexpanded sonic nozzle for two exit lip thicknesses of 0.200 and 0.625 nozzle diameters. Fluctuating measurements were obtained on the nozzle exit surface as well as in the acoustic nearfield. Narrowband spectra are presented for numerous operating conditions expressed in terms of the fully expanded Mach number based on nozzle pressure ratio.

Ponton, Michael K.↗

NASA NTRS1996

Shock-free supersonic elliptic nozzles and method of forming same

A method of forming a shock-free supersonic elliptic nozzle, in which the nozzle to be designed is divided into three sections, a circular-to-elliptic section which begins at a circular nozzle inlet, an elliptic subsonic section downstream from the circular-to-elliptic section and a supersonic section downstream from the elliptic subsonic section. The maximum and minimum radii for each axial point in the circular-to-elliptic section and the elliptic subsonic section are then separately determined, the maximum and minimum radii being the radii for the widest part of an elliptic cross-section and the narrowest part of the elliptic cross-section, respectively. The maximum and minimum radii for each axial point in the supersonic section are determined based on the Method of Characteristics, Then, each of the three sections are based on the maximum and minimum radii for each axial point in the section. The resulting nozzle is acoustically superior.

Seiner, John M.↗

NASA NTRS1995

Acoustic Study of B Helical Mode for Choked Axisymmetric Nozzle

An acoustic near-field study was performed for an axisymmetric conical convergent nozzle operating at a pressure ratio corresponding to a fully expanded Mach number of 1.3. The acoustic measurements were performed in the nozzle exit plane using multiple sensors arranged around the periphery of the nozzle. The acquired data were simultaneously digitized. The acoustic spatial characteristics, describing the large-scale structure associated with the preferred shear layer instability mode, were determined for the dominant B screech mode. The nozzle was fitted with a lip thickening device to determine the effect of this geometric variable on the spatial structure of the jet. For the thin-lipped configuration, the flapping structure of the B screech mode was found to precess in a time- dependent manner about the jet axis. Increasing of the nozzle exit lip thickness altered the spatial characteristics of this mode from a flapping to a time-dependent flapping or spinning. Using the autobicoherence spectrum, frequency dependencies were found to exist in the acoustic data of the thick-lipped configuration. These dependencies may be related to the nonlinearity of the jet and/or the time-dependent nature of the B mode spatial structure.

Ponton, Michael K.↗

NASA NTRS1994

Mach wave emission from a high-temperature supersonic jet

The paper considers the compressible Rayleigh equation as a model for the Mach wave emission mechanism associated with high-temperature supersonic jets. Solutions to the compressible Rayleigh equation reveal the existence of several families of supersonically convecting instability waves. These waves directly radiate noise to the jet far field. The predicted noise characteristics are compared to previously acquired experimental data for an axisymmetric Mach 2 fully pressure balanced jet operating over a range of jet total temperatures from ambient to 1370 K. The results of this comparison show that the first-order supersonic instability wave and the Kelvin-Hemlhlotz first-, second-, and third-order modes have directional radiation characteristics that are in agreement with observed data. The assumption of equal initial amplitudes for all of the waves leads to the conclusion that the flapping mode of instability dominates the noise radiatio process of supersonic jets. At a jet temperature of 1370 K, supersonic instability waves are predicted to dominate the noise radiated at high frequency at narrow angles to the jet axis.

Seiner, John M.↗

NASA NTRS1993

Shock-free supersonic elliptic nozzles and method of forming same

A method of forming a shock-free supersonic elliptic nozzle, in which the nozzle to be designed is divided into three sections, a circular-to-elliptic section which begins at a circular nozzle inlet, an elliptic subsonic section downstream from the circular-to-elliptic section, and a supersonic section downstream from the elliptic subsonic section is described. The maximum and minimum radii for each axial point in the circular-to-elliptic section and the elliptic subsonic section are then separately determined, the maximum and minimum radii being the radii for the widest part of an elliptic cross-section and the narrowest part of the elliptic cross-section, respectively. The maximum and minimum radii for each axial point in the supersonic section are determined based on the Method of Characteristics. Then, each of the three sections are based on the maximum and minimum radii for each axial point in the section. The resulting nozzle is acoustically superior.

Seiner, John M.↗

NASA NTRS1992

Supersonic acoustic source mechanisms for free jets of various geometries

The aeroacoustic performance of several generic nozzle geometries was tested to evaluate the potential benefits of using non-round jet exit geometries to reduce noise from combat military aircraft. Both the aerodynamics and far field acoustics of several M(sub d) = 1.5 and 2.0 round, elliptic, and rectangular nozzles, including an augmented deflector exhaust nozzle (ADEN), were studied to assess noise emission. The nozzles were operated to jet total temperatures, T(sub 0) = 1160 degree R, and the data scaled to constant thrust. The data were propagated to 1500 ft. and corrected to perceived noise level. The aerodynamic results of the study show that the non-round nozzle geometries mix much faster with the surrounding medium than does an equivalent round nozzle plume. Both the ADEN and elliptic nozzles provide significant reduction of noise, 6 to 7 PNdB, along the major axis direction with little expected impact on nozzle performance. Shock noise processes are eliminated for elliptic nozzles, but are still significant with rectangular nozzles. Comparison of measurements to theoretical predictions of noise using the quasi-linear instability wave model demonstrates good qualitative agreement.

Seiner, John M.↗

NASA NTRS1992

NASA/LaRC jet plume research

The following provides a summary for research being conducted by NASA/LaRC and its contractors and grantees to develop jet engine noise suppression technology under the NASA High Speed Research (HSR) program for the High Speed Civil Transport (HSCT). The objective of this effort is to explore new innovative concepts for reducing noise to Federally mandated guidelines with minimum compromise on engine performance both in take-off and cruise. The research program is divided into four major technical areas: (1) jet noise research on advanced nozzles; (2) plume prediction and validation; (3) passive and active control; and (4) methodology for noise prediction.

Seiner, John M.↗

NASA NTRS1992

A wind tunnel application of large-field focusing schlieren

A large-field focusing schlieren apparatus was installed in the NASA Lewis Research Center 9 by 15 foot wind tunnel in an attempt to determine the density gradient flow field of a free jet issuing from a supersonic nozzle configuration. The nozzle exit geometry was designed to reduce acoustic emissions from the jet by enhancing plume mixing. Thus, the flow exhibited a complex three-dimensional structure which warranted utilizing the sharp focusing capability of this type of schlieren method. Design considerations concerning tunnel limitations, high-speed photography, and video tape recording are presented in the paper.

Ponton, Michael K.↗

NASA NTRS1992

The effects of temperature on supersonic jet noise emission

This paper examines the generation of sound produced by high temperature supersonic jets. In particular, the question of the importance of supersonic instability waves to noise emission is considered relative to the role of Kelvin-Helmholtz (K-H) instability waves. Here, these waves are taken to be synonymous with the Mach emission process. Jet total temperatures from 313 to 1534 K are investigated using an axisymmetric water cooled supersonic nozzle designed for Mach 2. The aerodynamic and acoustic results of this study indicate that the dominant noise contributors are the K-H waves over the entire temperature range. Good agreement between measured and numerically predicted plume properties are obtained and an elliptic nozzle is used to demonstrate reduction of the K-H waves.

Seiner, John M.↗

NASA NTRS1992

Fluid dynamics and noise emission associated with supersonic jets

Methods have long been sought to find an efficient means for reduction of jet noise using either active or passive turbulence control measures. Progress in this area is limited by unclear understanding of the physical supersonic jet noise source mechanisms as they relate to the jet plume turbulence structure. These mechanisms have been extensively studied using round jets. This paper shows that jets with nonround jet exit geometry can provide beneficial noise reduction relative to round jets. Both the fluid dynamic structure and noise of several nonround jets are examined in the paper.

Seiner, John M.↗

NASA NTRS1991

Study of external dynamic flap loads on a 6 percent B-1B model

The origin of dynamic pressure loads on external divergent engine nozzle flaps of the B-1B aircraft was investigated in the NASA/LaRC 16 foot transonic tunnel using a 6 percent full span model with powered engine nacelles. External flap dynamic loads and afterbody drag associated with flap removal were measured using this model. Both dry and max. A/B power nozzles were evaluated in this study. As a result of this study, the principal mechanisms responsible for high dynamic external flap loads were determined along with performance penalty associated with flap removal.

Seiner, John M.↗

NASA NTRS1991

The spatial characteristics of the B helical mode for a choked axisymmetric nozzle

An acoustic near-field study was performed for an axisymmetric conical nozzle operated at a fully expanded Mach number of 1.3. The acoustic measurements were performed in the nozzle exit plane using multiple sensors arranged around the periphery of the nozzle. The acquired data were simultaneously digitized. The acoustic spatial characteristics, describing the large scale structure associated with the preferred shear layer instability mode, were determined for the dominant B screech mode. The nozzle was fitted with a lip thickening device to determine the effect of this geometric variable on the spatial structure of the jet. For the thin-lipped configuration, the flapping structure of the B screech mode was found to precess in a time-dependent manner about the jet axis. An increasing of the nozzle exit lip thickness altered the spatial characteristics of this mode from a flapping to a time-dependent flapping or spinning. Using the auto-bicoherence spectrum, frequency dependencies were found to exist in the acoustic data of the thick-lipped configuration. These dependencies may be related to the nonlinearity of the jet and/or the time-dependent nature of the B mode spatial structure.

Ponton, Michael K.↗