Search NASA⌕ Search

Engineering topics

Seiser, Reinhard

Publications and source records attributed to Seiser, Reinhard.

Impacts of Biomass Feedstock Pre-Processing on Heat and Mass Transfer During Pyrolysis Using X-Ray Computed Tomography and Multiscale Modeling

Knowledge of the transport properties of biomass particles such as porosity, tortuosity, and permeability is paramount for high-fidelity modeling of biomass pyrolysis due to the heat and mass transfer limitations imposed by particle microstructure. X-ray computed tomography (XCT) is a non-destructive imaging method that enables full 3D reconstructions of the biomass particle microstructure with high resolution, permitting direct calculation of porosity, tortuosity, and permeability from real particle geometries. In this study, XCT imaging revealed the 3D microstructures of particles and chars from pyrolytic conversion of cylindrically cut or milled/pelletized loblolly pine samples. The porosity, tortuosity, and permeability were calculated directly from the XCT geometries via open-source microstructural analysis tool MATBOX+TauFactor (https://github.com/NREL/MATBOX_Microstructure_analysis_toolbox) and computational fluid dynamics (CFD) simulations using our solver, Mesoflow (https://github.com/NREL/mesoflow). These properties were used in a reactor scale model developed in COMSOL of the single particle reactor at NREL to investigate the impact of feedstock pre-processing on biomass conversion during pyrolysis with rigorous experimental validation.

biomass↗

Chapter 4: "Waste"-to-Energy for Decarbonization - Transforming Nut Shells Into Carbon-Negative Electricity

This chapter presents a study demonstrating waste pistachio nut shells as a renewable feedstock for climate-friendly electricity generation via industrial gasification technology. The study includes biomass feedstock characterization (i.e., pistachio waste critical material attributes), process variability (i.e., bulk material handling), and overall operational reliability and conversion performance through extended testing. Additionally, techno-economic analysis (TEA) and life cycle assessment (LCA) were performed to assess the economic feasibility and environmental impact of the technology to transform agricultural waste to biopower. For processing pistachio waste material, among critical material attributes, fines content in the biomass (<1/4") had the largest potential to reduce the operating time of the gasifiers due to plugging. Pelletizing fines and co-feeding them with the mixed pistachio waste increased the average feed density, feed rate, and biochar production. Compared to pine wood chips, mixed pistachio waste yielded higher biochar quantity but slightly reduced quality. In general, a systematic Quality by Design methodology is the preferred approach for designing preprocessing and material conveyance systems, where a downstream technology (end user) for the produced intermediate is specified at the outset. TEA results show that the biochar production rate and selling price had an overwhelming impact on the modeled Minimum Electricity Selling Price (MESP), which ranged from 35.5 to 39.9 cents/kWh for the cases studied (16 h/day operational basis). Moreover, LCA results show that the valorization of pistachio shells for biopower generation is a "carbon negative" process that can help decarbonize the U.S. electricity grid. The specific carbon intensity was -0.29 to -0.71 kg CO2e/kWh, compared to 0.45 kg CO2e/kWh for the average U.S. electricity mix. Biochar production from pistachio waste as a potential means for carbon sequestration was a significant driver for the LCA. The highly stable biochar permanently sequesters a considerable fraction of biochar carbon in the ground, more than enough to offset the life cycle emissions, and can be a complementary climate change mitigation strategy.

bio-char↗

A Machine Learning Model for Predicting Composition of Catalytic Coprocessing Products from Molecular Beam Mass Spectra

Demand for the development of an automated and integrated refining process for biofuels has increased in recent years due to the lack of generalized process inspection tools. In bio-oil upgrading processes, all process variables are maintained based on the offline specification of intermediates and products. A lack of real-time product specifications in batch-wise monitoring can cause process failure and wasted resources. Therefore, there is a need for a fast and accurate intermediates/product specification tool that can be used for real-time specification to reduce waste and mitigate the risk of process failure. Here, to address this gap, we developed a machine learning (ML) model for predicting speciated bio-oil composition, including paraffin, iso-paraffins, olefins, naphthene, and aromatics. The model is trained using the mass spectra from upgraded products collected in the vapor phase before condensation and predicts the composition of the condensed product. Training ML models using raw mass spectra is challenging due to numerous overlapped peaks originating from different parent compounds. With this in mind, we propose a protocol that (i) transforms raw mass spectra to chemistry-inspired predefined features and (ii) trains decision tree-based models using these features. Our results show that the random forest model was robust against overfitting and had the highest accuracy compared to other models. Moreover, a stochastic ablation method determined the eight most significant features while maximizing the accuracy. Our protocol facilitates real-time compositional analysis of upgraded bio-oils and thus real-time process monitoring. Additionally, this protocol enables the rational design of efficient catalysts and the determination of optimal process conditions.

09 BIOMASS FUELS↗

Bio-Oil Co-Processing with Refinery Streams

The project seeks to accelerate the adoption of co-processing biomass-derived feedstocks with petroleum streams in operating petroleum refineries to produce biogenic-carbon-containing fuels.

bio-crude↗

Integration of Experimental Hydroprocessing and FCC Data with Process (Aspen Plus) and Refinery Optimization (Aspen PIMS) Models

NREL's Economic, Sustainability, and Market Analysis (ESMA) team develops process models in Aspen Plus to support techno-economic analysis (TEA) and life-cycle assessment (LCA) of conversion pathways from renewable and circular resources to fuels and chemicals. These tools are being applied to assess probable operational constraints or bottlenecks associated with refinery co-processing and repurposing opportunities. The team also utilizes optimizable refinery models to quantify opportunities for biofuel and bioproduct pathways through integration with existing refining infrastructure. The goals of analysis are to model the transition of refineries to renewable and circular feedstocks and quantify the costs production and CO2 abatement through utilization of existing refineries. At the core of the ESMA team's work is the process data derived from conversion experiments on hydroprocessing and fluid catalytic cracking performed at NREL. The objective of this presentation is to highlight new analysis approaches and capabilities in pathway analysis and refinery optimization modeling with specific emphasis on integration of experimental data.

BIOMASS FUELS,ENERGY PLANNING, POLICY, AND ECONOMY↗

Co-processing catalytic fast pyrolysis oil in an FCC reactor

Here, studies of co-processing catalytic fast pyrolysis (CFP) oil with vacuum gas oil (VGO) are conducted in a Davison Circulating Riser (DCR). The CFP oil (CFPO) for this study was produced by upgrading fast-pyrolysis vapors from pine in an ex-situ fixed-bed reactor. CFPOs were co-processed at up to a volume fraction of 0.05 with VGO at 521 degrees C and 257 kPa. The yields of oil, aqueous phase, tail gas, and coke were measured. The amount of coke was determined from the carbon containing components in the regenerator flue gas. A compositional analysis was conducted with gas chromatography and elemental analyzers. The organic liquids were distilled into gasoline, jet-fuel, diesel, and resid fractions. A biocarbon analysis was conducted on the organic phase and its individual boiling-point fractions. The results show a small decrease in liquid yield and a generally increased gas yield when co-processing CFPO with VGO. The experiments showed that 75%-100% of biocarbon is incorporated into liquid fuels relative to fossil carbon, depending on catalyst and CFPO. The measurements indicate that cracked CFPO components are predominantly included in the jet-fuel and diesel fractions. A techno-economic analysis (TEA) estimated the minimum fuel selling price (MSFP) for fuel-range products derived from FCC co-processing of CFPO at 24 to 29 $\$$/GJ ($\$$2.90 to $\$$3.50 per gasoline-gallon equivalent; GGE) at a yield of 4.87-7.14 GJ/t(biomass) or 40-58 GGE/t.

09 BIOMASS FUELS↗

Feedstock and Catalyst Impact on Bio-Oil Production and FCC Co-Processing to Fuels

NREL's thermochemical biomass conversion research is focused on ex-situ upgrading of biomass fast-pyrolysis (FP) vapors as an efficient route to completely biogenic pyrolysis-based fuel precursors, fuels, and value-added chemicals depending on catalyst and process conditions. A near term pathway being developed uses these liquids for co-processing with petroleum feedstocks to assess biogenic carbon incorporation in hydrocarbon fuel feedstocks for potential refinery use. In this work, the impact of feedstock and catalyst on catalytic fast pyrolysis oil (CFPO) composition was determined with the oils then assessed for biogenic fuel production via FCC (fluidized catalytic cracking) co-processing. Biomass vapors were generated via fast pyrolysis with destabilizing vapor components (char, inorganics, tar aerosols) removed by hot gas filtration to produce clean vapors more responsive to catalytic upgrading. A Davison Circulating Riser (DCR), a petroleum industry standard for fluidized catalytic cracking (FCC) catalyst evaluation, was coupled to a custom pyrolyzer system designed to produce consistent-composition pyrolysis vapors as feed to the DCR. Pyrolysis vapors, derived from pure hardwood and softwood, were upgraded using commercially available modified zeolite-based catalysts to produce CFPOs. These upgraded oils were analyzed via 31P and 13C NMR spectroscopy, GCxGC-TOF/MS, carbonyl and ultimate analysis (CHNO), and simulated distillation (SIMDIS) to assess both oil chemistry and distillation behavior as they relate to catalyst and feedstock type for producing fungible hydrocarbon product liquids. These exploratory vapor-phase-upgrading results demonstrated the feasibility of producing refinery-compatible hydrocarbon fuel intermediates entirely from biomass-derived fast-pyrolysis vapors using an industry-accepted DCR system for catalytic upgrading. The FCC co-processing results demonstrated the feasibility of using CFPOs with VGO feeds in FCC refinery operations to produce biogenic carbon containing fuels.

biogenic carbon↗

Co-Processing Catalytic Fast Pyrolysis Oil in an FCC Reactor

Studies of co-processing catalytic fast pyrolysis (CFP) oil with vacuum gas oil (VGO) are conducted in a Davison Circulating Riser (DCR). The CFP oil (CFPO) for this study was produced by upgrading fast-pyrolysis vapors from pine in an ex-situ fixed-bed reactor. CFPOs were co-processed at up to 5 vol% with VGO at 521°C and 2.57 bar. The yields of oil, aqueous phase, tail gas, and coke were measured. The amount of coke was determined from the carbon containing components in the regenerator flue gas. A compositional analysis was conducted with gas chromatography and elemental analyzers. The organic liquids were distilled into gasoline, jet-fuel, diesel, and resid fractions. A biocarbon analysis was conducted on the organic phase and its individual boiling-point fractions. The results show a small decrease in liquid yield and a generally increased gas yield when co-processing CFPO with VGO. For experiments with E-Cat as catalyst, approximately 70% of biocarbon is incorporated into liquid fuels relative to fossil carbon, while more of the biocarbon is contained in tail gas (as carbon dioxide or olefins) and/or coke. The measurements indicate that cracked CFPO components are predominantly included in the jet-fuel and diesel fractions. A techno-economic analysis (TEA) estimated the minimum fuel selling price (MSFP) for fuel-range products derived from FCC co-processing of CFPO at $3 to $4 per gasoline-gallon equivalent (GGE) at a yield of 51 GGE per ton of biomass.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Design Study for Bio-Oil Production from Biomass Using a Dual Fluidized-Bed Reactor

To evaluate the re-design and reconfiguration of a dual-fluidized bed (DFB) gasification system into a recirculating pyrolysis reactor, Computation Fluid Dynamic (CFD) simulations of the system were conducted. The Barracuda Virtual Reactor® computational particle fluid dynamic code was used to perform simulations of the pyrolysis process. Modeling of the chemical reaction kinetics for both gas phase and solid particle phase were included. The recirculating pyrolysis reactor shown in Fig. 1a is based on a bubbling-bed biomass pyrolyzer and a riser combustor to convert the remaining char. The operational differences in the re-configuration of the DFB gasification system into a recirculating pyrolysis system for the production of bio-oil are (1) replacement of a low-surface area inert bed material with a high-surface-area bed material that has acidic properties to provide catalytic activity for the production of bio-oil with reduced oxygen content, (2) lower temperature and residence time for bio-oil production from pyrolysis, (3) replacement of the fluidization gas in the bubbling bed pyrolyzer from steam to nitrogen, and (4) the reduction of pyrolyzer freeboard volume. The bed material used for catalytic pyrolysis is Sasol 300 (300-micron dia., bulk density 0.94 kg/l, and surface area 130 m2/g) and is a theta-alumina with mild acidity. This is in comparison with previous standard bed material Carbo HSP (430-micron dia., bulk density 2.01 kg/l, and surface area 0.03 m2/g) used for gasification. For bio-oil production, pyrolysis in the bubbling bed requires temperatures in the range of 550 C in comparison with gasification temperatures near 850 C. To attain this lower temperature requires management of the energy mass balances, with control of the bed material recirculation rate between bubbling bed pyrolyzer and riser combustor, the introduction of a nitrogen purge in the pyrolyzer, and adjusting the pressure balance between the two vessels. To extract bio-oil from the pyrolysis reactor with a snorkel, two different freeboard configurations were evaluated. In Fig. 1 b the existing high freeboard configuration is shown and in Fig. 1 c the reduced freeboard design is presented. The introduction of a nitrogen purge for the high free board configuration provided the highest bio-oil production from the CFD simulations. To decrease the bed-material circulation rate, primary and secondary air on the combustor side were reduced, and the pressure on the combustor was slightly increased. A portion of the biomass and bio-oil was observed to be transported to the combustor, leading to a smaller pyrolysis yield. The control of the pyrolyzer temperature is performed by controlling the circulation rate. Good fluidization of the bubbling bed and cascade PID control are required to keep the temperature from oscillating due to large time delay experienced when changing primary and secondary air. (a) (b) (c) Figure 1. (a) Dual Fluidized Bed pyrolysis system configuration, (b) mole fraction of nonpolar biooil in high freeboard configuration, and (c) mole fraction of nonpolar bio-oil in low freeboard configuration with nitrogen purge introduced in both configurations.

BASIC BIOLOGICAL SCIENCES,BIOMASS FUELS↗

An experimental and kinetic modeling study of combustion of isomers of butanol

A kinetic model is developed to describe combustion of isomers of butanol - n-butanol (n-C{sub 4}H{sub 9}OH), sec-butanol (sec-C{sub 4}H{sub 9}OH), iso-butanol (iso-C{sub 4}H{sub 9}OH), and tert-butanol (tert-C{sub 4}H{sub 9}OH). A hierarchical approach is employed here. This approach was previously found to be useful for developing detailed and semi-detailed mechanism of oxidation of various hydrocarbon fuels. This method starts from lower molecular weight compounds of a family of species and proceeds to higher molecular weight compounds. The pyrolysis and oxidation mechanisms of butanol isomers are similar to those for hydrocarbon fuels. Here, the development of the complete set of the primary propagation reactions for butanol isomers proceeds from the extension of the kinetic parameters for similar reactions already studied and recently revised for ethanol, n-propanol and iso-propanol. A detailed description leading to evaluation of rate constants for initiation reactions, metathesis reactions, decomposition reactions of alkoxy radicals, isomerization reactions, and four-center molecular dehydration reactions are given. Decomposition and oxidation of primary intermediate products are described using a previously developed semi-detailed kinetic model for hydrocarbon fuels. The kinetic mechanism is made up of more than 7000 reactions among 300 species. The model is validated by comparing predictions made using this kinetic model with previous and new experimental data on counterflow non-premixed flames of n-butanol and iso-butanol. The structures of these flames were measured by removing gas samples from the flame and analyzing them using a gas chromatograph. Temperature profiles were measured using coated thermocouples. The flame structures were measured under similar conditions for both fuels to elucidate the similarities and differences in combustion characteristics of the two isomers. The profiles measured include those of butanol, oxygen, carbon dioxide, water vapor, carbon monoxide, hydrogen, formaldehyde, acetaldehyde, and a number of C{sub 1}-C{sub 4} hydrocarbon compounds. The predictions of the kinetic model of flame structures of the two isomers were satisfactory. Validation of the kinetic model was also performed by comparing predictions with experimental data reported in the literature. These data were obtained in batch reactors, flow reactors, jet-stirred reactors, and shock tubes. In these configurations, combustion is not influenced by molecular transport. The agreement between the kinetic model and experimental data was satisfactory. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An experimental and kinetic modeling study of n-propanol and iso-propanol combustion

A kinetic model is developed to describe combustion of n-propanol and iso-propanol. It is validated by comparing predictions made using this kinetic model with new experimental data on structures of counterflow non-premixed flames and previously reported data over a wide range of configurations and conditions. The elementary pyrolysis reactions of methanol and ethanol are well-known and were used as a starting point for extension to propanol. A detailed description leading to evaluation of rate constants for initiation reactions, metathesis reactions, decomposition reactions, and four-center molecular dehydration reactions are given. Decomposition and oxidation of primary intermediate products are described using a previously developed semi-detailed kinetic model for hydrocarbon fuels. The kinetic mechanism is made up of more than 7000 reactions among 300 species. The structures of counterflow non-premixed flames were measured by removing gas samples from the flame and analyzing the samples using a gas chromatograph. The flame structures were measured under similar conditions for both fuels to elucidate the similarities and differences in combustion characteristics of the two isomers. The profiles measured include those of formaldehyde, acetaldehyde, propanal, and acetone. These species are considered to be pollutants. Validation of the kinetic model was first performed by comparing predictions with experimental data reported in the literature obtained in flow reactors and shock tubes. In these configurations, combustion is not influenced by molecular transport. The agreement between the kinetic model and experimental data was satisfactory. The predictions of the kinetic model were then compared with new and previously reported experimental data on structures of counterflow non-premixed flames of both isomers. The agreement between the kinetic model and experimental data was again satisfactory. Satisfactory agreement was also obtained when the predictions of the kinetic model were compared with experimental data obtained on low pressure burner stabilized premixed flames. The kinetic model was thus validated over a wide range of temperatures (from 900 K to 2000 K), and configurations. In general the structures and overall combustion characteristics of n-propanol flames and iso-propanol flames are similar. Acetone is formed under all conditions in iso-propanol flames, while propanal is formed in n-propanol flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗