Search NASA⌕ Search

Engineering topics

Selberg, B. P.

Publications and source records attributed to Selberg, B. P..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Investigation of chord ratio, stagger, decalage angle, and flap angle for dual wing configurations

Aerodynamical closely coupled dual wing configurations of unequal chords are investigated for medium speed general aviation applications. Vortex panel and momentum boundary layer analysis are utilized for the two-dimensional predictions. A multi-surface vortex lattice method is used for the three-dimensional predictions. In the process of searching for the highest lift to drag ratio upper airfoil to lower airfoil chord ratios, both greater than and less than one, are investigated in terms of stagger, decalage angle, and gap. With the optimum chord ratio, at the optimum stagger and gap, proper spanwise decalage distribution is shown to yield the lowest two dimensional drag results. Various wing taper ratios and wing twists are investigated to increase wing efficiency. Comparisons are made between optimized dual and optimized single wing configurations both with the same fuselage, stabilator surfaces, engines, payload, and fuel. The dual wing configuration is shown to have significantly less drag and hence longer range than the conventional single wing configuration.

Selberg, B. P.↗
NASA NTRS1985

Aerodynamic-structural study of canard wing, dual wing, and conventional wing systems for general aviation applications

An analytical aerodynamic-structural airplane configuration study was conducted to assess performance gains achievable through advanced design concepts. The mission specification was for 350 mph, range of 1500 st. mi., at altitudes between 30,000 and 40,000 ft. Two payload classes were studied - 1200 lb (6 passengers) and 2400 lb (12 passengers). The configurations analyzed included canard wings, closely coupled dual wings, swept forward - swept rearward wings, joined wings, and conventional wing tail arrangements. The results illustrate substantial performance gains possible with the dual wing configuration. These gains result from weight savings due to predicted structural efficiencies. The need for further studies of structural efficiencies for the various advanced configurations was highlighted.

Selberg, B. P.↗
NASA NTRS1984

Aerodynamic canard/wing parametric analysis for general aviation applications

Vortex panel and vortex lattice methods have been utilized in an analytic study to determine the two- and three-dimensional aerodynamic behavior of canard and wing configurations. The purpose was to generate data useful for the design of general aviation canard aircraft. Essentially no two-dimensional coupling was encountered and the vertical distance between the lifting surfaces was found to be the main contributor to interference effects of the three-dimensional analysis. All canard configurations were less efficient than a forward wing with an aft horizontal tail, but were less sensitive to off-optimum division of total lift between the two surfaces, such that trim drag could be less for canard configurations. For designing a general aviation canard aircraft, results point toward large horizontal and vertical distance between the canard and wing, a large wing-to-canard area ratio, and with the canard at a low incidence angle relative to the wing.

Keith, M. W.↗
NASA NTRS1983

Aerodynamic investigation of closely coupled lifting surfaces with positive and negative stagger for general aviation applications

Aerodynamic closely coupled lifting surfaces were investigated for both conventional tail aft configurations and canard configurations to determine whether positive stagger or negative stagger had more attractive aerodynamic characteristics. An inviscid multi-element vortex panel program was used in conjunction with a momentum integral boundary layer program to predict two-dimensional aerodynamic characteristics. A multi-element vortex lattice program was used for three-dimensional characteristics. Pressure distributions, transition location, momentum thickness, two- and three-dimensional drag, and boundary layer separation were compared for the positive and negative stagger case. For staggers less than six the results demonstrated that positive stagger configurations are aerodynamically superior.

Selberg, B. P.↗
NASA NTRS1983

Aerodynamic optimization, comparison, and trim design of canard and conventional high performance general aviation configurations

A design study has been conducted to optimize trim cruise flight of high performance general aviation canard aircraft which achieve minimum drag. In order to investigate the advantages and disadvantages of canard configured aircraft, corresponding conventional tail-aft 'baseline' aircraft were designed and used for comparison. Two-dimensional predictions were obtained by coupling inviscid results from a vortex panel multi-element program to a momentum integral boundary layer analysis. Using the results of the two-dimensional vortex panel analysis, a vortex lattice method was employed to predict the finite wing results. The analysis utilized a turbulent airfoil and a natural laminar airfoil which are two NASA state-of-the-art airfoil sections. The canard aircraft designs give quantitative results of wing and canard loadings, wing-to-canard moment arm ratios, and aspect ratio effects for trim cruise flight for a wide range of wing-to-canard area ratios. Both canard and baseline aircraft achieved a 25 to 30 percent improvement in performance over typical current technology aircraft, but high canard loading necessary for trim resulted in slightly poorer performance of the canard aircraft as compared to the baseline designs.

Keith, M. W.↗
NASA NTRS1982

Dual wing, swept forward swept rearward wing, and single wing design optimization for high performance business airplanes

An investigation was performed to compare closely coupled dual wing and swept forward swept rearward wing aircraft to corresponding single wing 'baseline' designs to judge the advantages offered by aircraft designed with multiple wing systems. The optimum multiple wing geometry used on the multiple wing designs was determined in an analytic study which investigated the two- and three-dimensional aerodynamic behavior of a wide range of multiple wing configurations in order to find the wing geometry that created the minimum cruise drag. This analysis used a multi-element inviscid vortex panel program coupled to a momentum integral boundary layer analysis program to account for the aerodynamic coupling between the wings and to provide the two-dimensional aerodynamic data, which was then used as input for a three-dimensional vortex lattice program, which calculated the three-dimensional aerodynamic data. The low drag of the multiple wing configurations is due to a combination of two dimensional drag reductions, tailoring the three dimensional drag for the swept forward swept rearward design, and the structural advantages of the two wings that because of the structural connections permitted higher aspect ratios.

Rhodes, M. D.↗
NASA NTRS1980

Aerodynamic-structural analysis of dual bladed helicopter systems

The aerodynamic and structural feasibility of the birotor blade concept is assessed. The inviscid flow field about the dual bladed rotor was investigated to determine the aerodynamic characteristics for various dual rotor blade placement combinations with respect to blade stagger, gap, and angle of attack between the two blades. The boundary layer separation on the rotors was studied and three dimensional induced drag calculations for the dual rotor system are presented. The thrust and power requirements of the rotor system were predicted. NASTRAN, employed as the primary modeling tool, was used to obtain a model for predicting in plane bending, out of plane bending, and the torsional behavior of the birotors. Local hub loads, blade loads, and the natural frequencies for the birotor configuration are discussed.

Selberg, B. P.↗