Search NASA⌕ Search

Engineering topics

Self, Ethan C.

Publications and source records attributed to Self, Ethan C..

At least 19 records

The Impact of Lithium Anode Interface on Capacity Fade in Polymer Electrolyte-Based Solid-State Batteries

This study investigates the Li stripping-plating morphology and failure mechanisms in full cells consisting of a solid polymer electrolyte (SPE) with two commercial Li anodes: Li chip and Li foil. The primary identified failure mechanism of the SPE cell is capacity fade, regardless of the Li manufacturer. While the cathode’s role in capacity fade is evident, the Li anode significantly influences cycling performance, with Li foil cells cycling 50% longer than Li chip cells, a statistical difference. Further, post-mortem scanning electron microscopy and X-ray photoelectron spectroscopy results attribute the Li chip’s faster capacity fade to a loss of contact and continuous growth of the solid electrolyte interphase (SEI). Conversely, Li foil maintains consistent contact with the solid polymer, displaying a thin and stable SEI. Additionally, failure mechanisms between a gel electrolyte in previous work and the dry SPE are compared.

25 ENERGY STORAGE↗

Direct Mapping of Fluorine in Cation Disordered Rocksalt Cathodes

Cation-disordered rocksalt (DRX) oxides are promising candidates as next-generation cathodes for lithium-ion batteries. Partial fluorination of the DRX oxides enhances their cyclability. However, the lattice position, concentration, and spatial distribution of fluorine within DRX lattices remain elusive. Here, in this work, we use atom location by channeling-enhanced microanalysis, energy-dispersive X-ray spectroscopy, electron energy loss spectroscopy, and integrated differential phase contrast imaging in a scanning transmission electron microscope to gain atomic-level insights into DRX with nominal composition of Li 1.2 Mn 0.7 Ti 0.1 O 1.7 F 0.3 and Li 1.15 Ni 0.45 Ti 0.3 Mo 0.1 O 1.85 F 0.15 . We reveal that fluorine substitutes oxygen in the DRX lattices. The O/F ratio in terms of O+F = 2 is in the range from 1.92:0.08 to 1.82:0.18. Spatially, fluorine is distributed in the proximity of the Li-rich regions but distinct from lithium fluoride. Additionally, we observe that incorporation of fluorine in the DRX lattice induces a larger variation in cation–anion separation. These observations provide insight into the guided design of oxyfluoride DRX cathodes for high-performance batteries.

(S)TEM↗

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Previous studies have demonstrated that chemical vapor deposition carbon coating on silicon (Si@C) can enhance the electrochemical performance of lithium-ion batteries with Si-based anodes. However, the underlying mechanisms contributing to this improvement have not been fully explored. Here, we address this knowledge gap by applying a suite of characterization methods to evaluate Si@C anodes prepared by reducing acetylene on ball-milled Si particles. Raman mapping measurements show that the C coating (<5 nm thick) enables a homogeneous Si and carbon distribution during the slurry casting process, thereby promoting Si utilization during cycling. The coating’s microstructure and morphology were evaluated using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy, and neutron reflectivity experiments. Electrochemical impedance spectroscopy measurements upon cycling indicate that carbon coating also reduces the overall resistance as benchmarked against bare Si anodes. Galvanostatic cycling in half-cell studies revealed higher initial Coulombic efficiency and specific capacities with increasing carbon coating time. However, solid electrolyte interphase (SEI) investigations using XPS showed that the coated and uncoated samples have very similar characteristics, suggesting that the SEI may only play a minor role in enhancing the performance of Si@C. Full-cell evaluation of the Si electrodes was consistent with half-cell results relating to performance and SEI properties, further supporting the conclusion that electronic and ionic percolation, enabled by effective electrode manufacturing, are the dominant factors contributing to the favorable performance of Si@C.

25 ENERGY STORAGE↗

Navigating the complexities of solvent and binder selection for solution processing of sulfide solid-state electrolytes

We introduce a paradigm of solvent and binder selection for solution-processing Li 6 PS 5 Cl solid-state electrolyte particles based on Hansen solubility parameters. Treatment of the Li 6 PS 5 Cl in selected solvents results in particle morphological change, but crystallographic structure remains intact. Although solution processing reduced the Li 6 PS 5 Cl ionic conductivity, it promotes interfacial stability by alleviating reduction of the solid electrolyte in contact with Li metal. In conclusion, these findings have the potential to enhance the stability, structural integrity, and performance of sulfide solid-state electrolytes in practical applications.

25 ENERGY STORAGE↗

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes Enabled by a Graphite Conductive Additive

Cobalt-free cation-disordered rocksalt (DRX) cathodes are a promising class of materials for next-generation Li-ion batteries. Although they have high theoretical specific capacities (>300 mA h/g) and moderate operating voltages (~3.5 V vs Li/Li + ), DRX cathodes typically require a high carbon content (up to 30 wt %) to fully utilize the active material which has a detrimental impact on cell-level energy density. To assess pathways to reduce the electrode’s carbon content, the present study investigates how the carbon’s microstructure and loading (10–20 wt %) influence the performance of DRX cathodes with the nominal composition Li 1.2 Mn 0.5 Ti 0.3 O 1.9 F 0.1 . While electrodes prepared with conventional disordered carbon additives (C65 and ketjenblack) exhibit rapid capacity fade due to an unstable cathode/electrolyte interface, DRX cathodes containing 10 wt % graphite show superior cycling performance (e.g., reversible capacities ~260 mA h/g with 85% capacity retention after 50 cycles) and rate capability (~135 mA h/g at 1000 mA/g). Furthermore, a suite of characterization tools was employed to evaluate the performance differences among these composite electrodes. Overall, these results indicate that the superior performance of the graphite-based cathodes is largely attributed to the: (i) formation of a uniform graphitic coating on DRX particles which protects the surface from parasitic reactions at high states of charge and (ii) homogeneous dispersion of the active material and carbon throughout the composite cathode which provides a robust electronically conductive network that can withstand repeated charge–discharge cycles. Overall, this study provides key scientific insights on how the carbon microstructure and electrode processing influence the performance of DRX cathodes. Based on these results, exploration of alternative routes to apply graphitic coatings is recommended to further optimize the material performance.

25 ENERGY STORAGE↗

Composite Membrane for Sodium Polysulfide Hybrid Redox Flow Batteries

Non-aqueous redox flow batteries (NARFBs) using earth-abundant materials, such as sodium and sulfur, are promising long-duration energy storage technologies. NARFBs utilize organic solvents, which enable higher operating voltages and potentially higher energy densities compared with their aqueous counterparts. Despite exciting progress throughout the past decade, the lack of low-cost membranes with adequate ionic conductivity and selectivity remains as one of the major bottlenecks of NARFBs. Here, we developed a composite membrane composed of a thin (<25 µm) Na+-Nafion coating on a porous polypropylene scaffold. The composite membrane significantly improves the electrochemical stability of Na + -Nafion against sodium metal, exhibiting stable Na symmetric cell performance for over 2300 h, while Na + -Nafion shorted by 445 h. Additionally, the composite membrane demonstrates a higher room temperature storage modulus than the porous polypropylene scaffold and Na + -Nafion separately while maintaining high Na + conductivity (0.24 mS/cm at 20 °C). Our method shows that a composite membrane utilizing Na + -Nafion is a promising approach for sodium-based hybrid redox flow batteries.

25 ENERGY STORAGE↗

Deposition and characterization of α-Fe 2 O 3 /Pd thin films for neutron reflectometry studies

Here, we report deposition of hematite/Pd thin films on silicon wafers via radio frequency (RF) magnetron sputtering and subsequent characterization for future in situ neutron reflectometry studies. Following deposition, the hematite/Pd thin films were characterized as prepared and after annealing in air for 2h at 400, 500, and 600 °C, respectively. Raman spectroscopy, grazing incidence x-ray diffraction, and neutron reflectometry (NR) were used to characterize the structure and chemical compositions of the thin films. The results indicate that pure α-Fe 2 O 3 (hematite) films were produced, free from other iron oxide phases and impurities. NR data reveal that one intermediate layer between the Pd layer and the hematite layer was formed during sputtering deposition processes. The fitted scattering length density (SLD) of the as-deposited hematite layer is 70% of the theoretical SLD value, indicating that the grains are loosely packed in the RF-deposited hematite films. After annealing at elevated temperatures, the hematite films show increased SLD values but remain comparable to that of preannealed.

36 MATERIALS SCIENCE↗

Modeling Short-Range Order in Disordered Rocksalt Cathodes by Pair Distribution Function Analysis

Pair distribution function (PDF) analysis is a powerful technique for the characterization of short-range order (SRO) in disordered materials. Accurate interpretation of experimental PDF data is critically reliant on the development of structural models that can account for local variations in site occupancies and bond lengths. To this end, we outline an approach to model SRO using first-principles calculations based on the cluster-expansion formalism. These methods are validated on neutron scattering data from two disordered rocksalt oxyfluorides, Li 1.3 Mn 0.4 Ti 0.3 O 1.7 F 0.3 and Li 1.3 Mn 0.4 Nb 0.2 Ti 0.1 O 1.7 F 0.3 . For each composition, we demonstrate that an average structure without any SRO fails to reproduce several key features in the experimental PDF. To pinpoint the origin of the suspected SRO in these materials, configurational and displacive effects were separately investigated using two disparate models. Special quasi-random structures were relaxed using density functional theory to account for local changes in bond lengths while maintaining a near-random ionic configuration. This leads to slightly improved accuracy but still misrepresents asymmetry in the first few peaks of the PDF. Monte Carlo simulations were performed to model configurational SRO on a fixed lattice, which by itself is shown to have a minimal influence on the PDF. Instead, we find that it is the bond length relaxations within environments created by SRO which controls the details of the PDF, thereby highlighting the subtle but important coupling between configurational and displacive SRO in disordered materials.

36 MATERIALS SCIENCE↗

Alternate Synthesis Method for High-Performance Manganese Rich Cation Disordered Rocksalt Cathodes

Cation-disordered rocksalt (DRX) cathodes have recently emerged as a promising class of cobalt-free, high-capacity cathodes for lithium-ion batteries. To facilitate their commercialization, the development of scalable synthesis techniques providing control over composition and morphology is critical. To this end, a sol-gel synthesis route to prepare Mn-rich DRX cathodes with high capacities is presented here. Several compositions with varied Mn content and nominal F doping are successfully prepared using this technique. In-situ X-ray diffraction measurements demonstrate that DRX formation proceeds at moderate temperature (800 °C) through the sol-gel route, which enables intimate mixing among reactive intermediate phases that form at lower temperatures. All synthesized compositions possess cation short-range order, as evidenced by neutron pair distribution function and electron diffraction analysis. These DRX materials demonstrate promising electrochemical performance with reversible capacities up to 275 mAh g. Compared to the baseline oxide (Li 1.2 Mn 0.4 Ti 0.4 O 2 ), the Mn-rich compositions exhibit improved cycling stability, with some showing an increase in capacity upon cycling. Finally, this study demonstrates the feasibility of preparing high-capacity DRX cathodes through a sol-gel based synthesis route, which may be further optimized to provide better control over the product morphology compared to traditional synthesis methods.

25 ENERGY STORAGE↗

An overview of cobalt-free, nickel-containing cathodes for Li-ion batteries

The need for high-energy, low-cost batteries is projected to grow dramatically in the next decade due to electrification of the transportation market. Such demands are straining Li-ion supply chains for critical materials including lithium, nickel, and cobalt. Price instability, environment toxicity, and limits in the absolute supply lead to great concern for the continued use of cobalt. Similar to cobalt, the required grade of nickel for batteries, known as Class 1 nickel, has also been declining due to geological scarcity and low incentive prices. Herein, this review summarizes alternative cathode chemistries with no cobalt and reduced nickel content for high-energy Li-ion batteries targeting sustainable growth in the electric vehicle market. Further, the primary challenges associated with each material system are generally classified as being related to four common categories: (1) ion instability during charging, (2) poor electronic conductivity, (3) poor ionic conductivity, and (4) poor thermal stability.

25 ENERGY STORAGE↗

Early transition metal stabilized high capacity cobalt free cathodes for lithium-ion batteries

A cathode for a lithium battery includes LiNi 0.5 -x/2Mn 0.5 -x/2M x O 2 where M is at least one selected from the group consisting of Mo, Ti, Cr, Zr and V, and x is between 0.005-0.02. The LiNi 0.5 -x/2Mn 0.5 -x/2M x O 2 can be coated with Mn 2 P 2 O 7 . The Mn 2 P 2 O 7 can be 1-3 wt. %, based on the total weight of the LiNi 0.5 -x/2Mn 0.5 -x/2M x O 2 and Mn 2 P 2 O 7 . A cathode composition, a lithium battery, and a method of making a lithium battery are also disclosed.

25 ENERGY STORAGE↗

Understanding the Fluorination of Disordered Rocksalt Cathodes through Rational Exploration of Synthesis Pathways

Here, we have designed and tested several synthesis routes targeting a highly fluorinated disordered rocksalt (DRX) cathode, Li 1.2 Mn 0.4 Ti 0.4 O 1.6 F 0.4 , with each route rationalized by thermochemical analysis. Precursor combinations were screened to raise the F chemical potential and avoid the formation of LiF, which inhibits fluorination of the targeted DRX phase. MnF 2 was used as a reactive source of F, and Li 6 MnO 4 , LiMnO 2 , and Li 2 Mn 0.33 Ti 0.66 O 3 were tested as alternative Li sources. Each synthesis procedure was monitored using a multi-modal suite of characterization techniques including X-ray diffraction, nuclear magnetic resonance, thermogravimetric analysis, and differential scanning calorimetry. From the resulting data, we advance the understanding of oxyfluoride synthesis by outlining the key factors limiting F solubility. At low temperatures, MnF 2 consistently reacts with the Li source to form LiF as an intermediate phase, thereby trapping F in strong Li-F bonds. LiF can react with Li 2 TiO 3 to form a highly lithiated and fluorinated DRX (Li 3 TiO 3 F); however, MnO is not easily incorporated into this DRX phase. Although higher temperatures typically increase solubility, the volatility of LiF above its melting point (848 °C) inhibits fluorination of the DRX phase. Based on these findings, metastable synthesis techniques are suggested for future work on DRX fluorination.

36 MATERIALS SCIENCE↗

Selective Plasticization of Poly (ethylene oxide) (PEO) Block in Nanostructured Polystyrene– PEO– Polystyrene Triblock Copolymer Electrolytes

The plasticization of a polymer electrolyte usually promotes its ionic conductivity but decreases its storage modulus due to the increased polymer chain flexibility. Herein, we show that such a tradeoff between the ionic conductivity and the mechanical robustness of the polymer electrolyte can be alleviated by selective plasticization of the ion-conductive block, such as poly(ethylene oxide) (PEO) in a polystyrene (PS)– PEO–PS block copolymer (SEO) electrolyte using an ether type plasticizer, tetraethylene glycol dimethyl ether (TEGDME). In this work, at maximum plasticizer loading, the room temperature ionic conductivity increases by up to 3 orders, whereas the storage modulus, G' reduces to half, is still on the order of 10 2 MPa. At above the melting temperature of the PEO block, the dynamic storage modulus, G' of the plasticized membrane surpasses its dry PS-PEO-PS counterpart. Such a phenomenon results from that, a) TEGDME co-crystallizes with PEO to promote its crystallinity and hence the storage modulus, b) TEGDME swells the amorphous PEO phase to enhance the polymer chain segmental mobility and hence ionic conductivity, and c) the PS phase remains intact from TEGDME to keep the SEO elastic.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Membrane design for non-aqueous redox flow batteries: Current status and path forward

Redox flow batteries are promising technologies for large-scale, long-duration energy storage applications. Among them, non-aqueous redox flow batteries (NARFB) represent a transformative flow battery system since NARFBs potentially offer a higher energy density than aqueous flow batteries. However, many technical challenges remain for NARFBs, including the lack of high-performance membranes, low solubility of redox materials, and poor cycling efficiencies. Membranes serve a vital function in NARFBs, as they allow for selective ion transport while providing separation between the anolyte and catholyte. NARFB membrane development is an emerging research area, and this article reviews their design and critical factors that influence membrane properties, including solvent uptake, ion transport, and redox species permeability. A greater understanding of membrane behavior in non-aqueous solutions provides design principles for developing next-generation membranes for NARFB. In conclusion, we summarize the challenges, target metrics, and future perspectives for NARFBs.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

High capacity organic radical mediated phosphorous anode for redox flow batteries

A battery includes a redox flow anode chamber coupled to an anode current collector, a separator, and an external container in fluid connection with the redox flow anode chamber. The external container has therein a solid phosphorus material. A first redox-active mediator and the second redox-active mediator are circulated through the half-cell electrode chamber and the external container. During a charging cycle the first redox-active mediator is reduced at the current collector electrode and the reduced first mediator reduces the phosphorus material, and wherein during a discharging cycle the second redox-active mediator is oxidized at the anode current collector electrode, and the second redox-active mediator is then reduced by the reduced phosphorus material. A method of operating a battery and a method of making a battery are also discussed.

Delnick, Frank M.↗

Heavily Tungsten–Doped Sodium Thioantimonate Solid–State Electrolytes with Exceptionally Low Activation Energy for Ionic Diffusion

A strategy for modifying the structure of solid-state electrolytes (SSEs) to reduce the cation diffusion activation energy is presented. Two heavily W-doped sodium thioantimonate SSEs, Na 2.895 W 0.3 Sb 0.7 S 4 and Na 2.7 W 0.3 Sb 0.7 S 4 are designed, both exhibiting exceptionally low activation energy and enhanced room temperature (RT) ionic conductivity; 0.09 eV, 24.2 mS/cm and 0.12 eV, 14.5 mS/cm. At –15 °C the Na 2.895 W 0.3 Sb 0.7 S 4 displays a total ionic conductivity of 5.5 mS/cm. Here, the 30 % W content goes far beyond the 10–12 % reported in the prior studies, and results in novel pseudo-cubic or orthorhombic structures. Calculations reveal that these properties result from a combination of multiple diffusion mechanisms, including vacancy defects, strongly correlated modes and excessive Na-ions. An all-solid-state battery (ASSB) using Na 2.895 W 0.3 Sb 0.7 S 4 as the primary SSE and a sodium sulfide (Na 2 S) cathode achieves a reversible capacity of 400 mAh g –1 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heavily Tungsten-Doped Sodium Thioantimonate Solid-State Electrolytes with Exceptionally Low Activation Energy for Ionic Diffusion

A strategy for modifying the structure of solid-state electrolytes (SSEs) to reduce the cation diffusion activation energy is presented. Two heavily W-doped sodium thioantimonate SSEs, Na 2.895 W 0.3 Sb 0.7 S 4 and Na 2.7 W 0.3 Sb 0.7 S 4 are designed, both exhibiting exceptionally low activation energy and enhanced room temperature (RT) ionic conductivity; 0.09 eV, 24.2 mS/cm and 0.12 eV, 14.5 mS/cm. At –15 °C the Na 2.895 W 0.3 Sb 0.7 S 4 displays a total ionic conductivity of 5.5 mS/cm. The 30 % W content goes far beyond the 10–12 % reported in the prior studies, and results in novel pseudo-cubic or orthorhombic structures. Here, calculations reveal that these properties result from a combination of multiple diffusion mechanisms, including vacancy defects, strongly correlated modes and excessive Na-ions. An all-solid-state battery (ASSB) using Na 2.895 W 0.3 Sb 0.7 S 4 as the primary SSE and a sodium sulfide (Na 2 S) cathode achieves a reversible capacity of 400 mAh g –1 .

sodium metal battery (SMB)↗

Ambient Temperature Sodium Polysulfide Catholyte for Nonaqueous Redox Flow Batteries

This study reports a sodium polysulfide catholyte for nonaqueous redox flow batteries (RFBs). We demonstrate reversible capacities up to 200 mAh/gS with negligible fade over 250 cycles at room temperature for sodium polysulfide|biphenyl full cells containing Na + ß '' -Al 2 O 3 solid electrolyte (BASE) membranes. Interestingly, formation of insoluble S and Na 2 S 4 phases did not inhibit the catholyte's cycle life which is likely due to the low concentrations used in the lab-scale prototypes. 3-electrode galvanostatic AC impedance measurements demonstrate that voltage losses were dominated by charge transfer at the cathode, and relevant kinetic parameters (i.e., transfer coefficients and exchange current density) were calculated through a Tafel analysis. To the best of our knowledge, this is the first report applying such an impedance approach to nonaqueous RFBs. Overall, the use of low-cost active materials makes sodium polysulfide|biphenyl RFBs promising for long duration energy storage applications. Furthermore, if strategies are developed to increase the solubility of S and/or low order polysulfides (Na 2 S x , x ≤ 4), specific energies up to 100 Wh kg -1 (including combined mass of the anolyte and catholyte) can be achieved.

25 ENERGY STORAGE↗