Search NASA⌕ Search

Engineering topics

Semelsberger, Troy Allen

Publications and source records attributed to Semelsberger, Troy Allen.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impacts of caking on corn stover – An assessment of moisture content and consolidating pressure

Caking or time consolidation of powders is a serious problem which can hinder productivity and overall feasibility of various industrial processes. Here this study focuses on the impacts moisture content and consolidating pressures can have on 2 mm corn stover samples after undergoing a drying treatment at different times. Individually, moisture content and consolidating pressure did not exhibit any significant changes throughout the modified variable flow rate tests using the FT4 powder rheometer. However, applying both variables simultaneously yielded higher-than-usual energy outputs from the corn stover, indicative of biomass agglomeration due to the moisture and its subsequent evaporation while under pressure via the induced consolidating pressure. However, despite the increase in energy usage, time dried did not have a direct effect and demonstrated no trend.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Resonant acoustic monitoring of damage in plug‐screw feeders

Abstract Plug‐screw feeders are critical in many industrial processes for compressing slurry materials via a rotating plug‐screw feeder. Over time, increasing plug‐screw feeder wear will eventually lead to catastrophic mechanical failure. Early detection of the wear state can prevent unplanned catastrophic failures resulting in operational shut‐downs, costly repairs, and most importantly the health and safety of workers. We present a theoretical basis for a noninvasive, in operando acoustic resonant technique to monitor the wear state of plug‐screw feeders. The technique is based on tracking the resonant acoustic modes of the plug‐screw feeder, which are sensitive to the plug‐screw feeder geometry, material, and operating conditions. We implemented a multivariate polynomial model to estimate the plug‐screw feeder wear state using multiple acoustic resonances by simulating the acoustic resonant modes for two categories of wear (tip and thread damage) that are common in plug‐screw feeders. Fitting multiple resonances to the polynomial model, we demonstrate accurate estimation of the total mass loss, as well as characterization of the type of damage (i.e., tip vs. thread). Current approaches for monitoring plug‐screw feeder wear rely on shutting down the operation and visually inspecting the plug‐screw feeder. The presented acoustic technique offers a noninvasive, in operando measurement approach that mitigates unplanned catastrophic failures. The acoustic resonance technique presented in the paper has a broad range of industrial applications including the Pharmaceutical, Mining, Integrated Biorefineries (IBR), and Additive Manufacturing industries, to name a few.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rheological effects of moisture content on the anatomical fractions of loblolly pine (Pinus taeda)

Here, this study focused on assessing the influence of moisture content on the rheological properties of different anatomical fractions of pine residue using the FT4 powder rheometer. Moisture content exhibited some influence on the 2 mm bark and needle fractions, increasing their cohesion, angle of internal friction, unconfined yield strength, and major principal stress. Stem and whole, on the other hand, presented minimal changes upon moisture introduction. All 4 mm fractions did not show many changes in their rheological properties with moisture introduction, which can be due to less particle-particle interactions and consequently reducing any liquid bridging the particles might undergo; however, they were shown to have a more unpredictable behavior compared to the 2 mm analogues (i.e., higher standard deviation) which can be due to a higher degree of particle-interlocking. Out of the three fractions, needle presented the poorest rheological properties for flowability in addition to being susceptible by moisture, unlike other fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impacts of Biologically Induced Degradation on Surface Energy, Wettability, and Cohesion of Corn Stover

The impacts of biological degradation on surface area, surface energy, wettability, and cohesion of anatomically fractionated (i.e., leaf, stalk, and cob) and bulk corn stover are presented in this study. The physical, thermal and chemical properties of corn stover are critical material attributes that not only influence the mechanical processing and chemical conversion of corn stover, but also the bulk solids handling and transport. The measured surface areas were observed to be dependent on the degree of biological degradation (mild vs. moderate vs. severe) and on the anatomical fraction. The surface area of the bulk corn stover samples increased with the degree of biological degradation. The leaf fraction was the most sensitive to biological degradation, resulting in an increase in surface area from 0.5 m 2 /g (mildly degraded) to 1.2 m 2 /g (severely degraded). In contrast, the surface area of the cob fraction remained relatively unaffected by the degree of biological degradation (i.e., mildly degraded–0.55 m 2 /g, severely degraded–0.40 m 2 /g. All biologically degraded samples resulted in significant changes to the surface chemistry (evidenced by an increase in surface energy. As a general trend, the surface energy of bulk corn stover increased with the degree of biological degradation—the same trend was observed for the leaf and stalk anatomical fractions; however, the surface energy for the cob fraction remained unchanged. Wettability, calculated from surface energy, for bulk corn stover samples did not reveal any discernable trend with the degree of biological degradation. However, trends in wettability were observed for the anatomical fractions, with wettability increasing for the stalk and leaf fractions, and decreasing for the cob fraction. Excluding the cob fraction, the work of cohesion increased with the degree of biological degradation. Understanding the impacts of biological degradation on the physical, chemical and thermal properties of corn stover offers insights to improve the overall operational reliability, efficiency and economics of integrated biorefineries.

09 BIOMASS FUELS↗
DOE OSTI2022

Effect of Moisture and Feedstock Variability on the Rheological Behavior of Corn Stover Particles

Continuous feeding, processing, and handling of biomass powders is pivotal to the economic viability of integrated biorefineries. However, current challenges associated with the operational reliability of bulk solids handling and transport greatly impact the process economics and ultimately the widespread commercialization of integrated biorefineries. In this work, we examine the effect of moisture and feedstock variability on the flow behavior of corn stover biomass particles. The total flow energy, compressibility, shear properties, and wall friction angles were measured for corn stover samples A and B containing 0%, 15%, 25%, 50%, and 75% (mass fraction) moisture contents using a FT4 powder rheometer. In general, the flowability of both A and B was reduced when moisture was present as indicated by the stability and variable flow rate, compressibility, and shear tests. The 15% moisture sample had the highest flow energy, revealing the interplay between the increased surface tension and looser packing both of which were caused by liquid bridging. The 75% moisture sample had the highest compressibility and the lowest flowability factor (ff c ). The trend in wall friction angle was found to be dependent upon the surface hydrophobicity of the wall material. The wall friction angle on the hydrophilic, stainless-steel surface increased with moisture and therefore poses additional handling challenges. On the other hand, the wall friction angle on the hydrophobic polymer surfaces were the lowest for samples with intermediate moisture contents. Sample B had greater bulk density, smaller compressibility, and greater flowability than the sample A , as suggested by the compressibility and shear tests. The wall friction angle of sample B was higher than or equal to that of sample A depending on both the type and the surface roughness of the wall material.

09 BIOMASS FUELS↗
DOE OSTI2021

Rheological Characterization of Biomass Feedstock for Alternative Energy Applications

With the increased necessity of alternative energy resources, bulk feedstock biomass materials were characterized with the purpose of replacing depleting energy supplies such as fossil fuels and other nonrenewable energy sources. Residual organic waste material (biomass) left over from agricultural processing and handling systems was recycled, and further investigated for renewable energy use. Understanding the scope of flowability for biomass material yielded more efficient, and economical crop harvesting, transporting, and storing method design for the agricultural industry. The effects of moisture on bulk solid flowability was investigated using a variety of parametric testing methods that measure basic flowability energy, and other properties such as compressibility and material resistance. In an industry where organic material is a wasteful byproduct, converting this biomass material into a new energy source and streamlining efficiently for innovative agricultural development supports a clean, renewable energy approach to everyday nonrenewable energy uses, such as oil, propane, and coal. As observed from the repeatable results from the investigated rheological material properties, biomass is an incredibly diverse material that requires modern engineering solutions to revolutionize biomass into a renewable energy source. Biomass will decarbonize petroleum (nonrenewable) derived fuels and chemicals, yielding recyclable carbon. This push to replace fossil fuels with recycled carbon is ideal because of the abundant, renewable, and otherwise agricultural waste of corn stover material. Decarburization, and reduction of C0 2 emissions reduces the effects of global warming.

09 BIOMASS FUELS↗
DOE OSTI2021

Flow behavior characterization of biomass Feedstocks

With the advancement of renewable energy, the processing and handling of biomass feedstocks has drawn enormous research interest. The key to economically viable and operationally reliable biomass handling processes involves a complete understanding of the flow behavior of different feedstocks as functions of the inherent critical material properties environmental conditions, and critical processing parameters. This review introduces the basic principles and methods in bulk solids flow and highlights recent efforts to understand the flow behavior of biomass feedstocks. The effects of inherent properties, environmental parameters, and handling equipment on the flow behavior of biomass feedstocks are presented. Particle size, shape, moisture, consolidation stress, temperature, storage time at rest, chemical treatment, and the material and geometry of the handling equipment all substantially influence biomass flowability. The limitations of current studies and the potential methods to overcome them are presented. Finally, an outlook for future research effort is provided, with proposed opportunities for improving the characterization of biomass flow.

Bulk solids testing↗
DOE OSTI2020

Role of phosphate source in improving the proton conductivity of tin pyrophosphate and its composite electrolytes

Metal pyrophosphates (MPPs) in general, and tin pyrophosphate (TPP) in particular, have received significant interest in the last decade due to their potential as proton conductors for electrolyte application in intermediate temperature (IT)-fuel cells. However, for MPP based electrolytes, despite high reported proton conductivities, achieving good fuel cell performance and high open circuit voltage (OCV) remains a challenge with synthesis methods playing a crucial role in determining the final proton conductivity. Here we report the role of phosphate precursor in determining the TPP proton conductivity by examining five different precursors: (1) phosphoric acid (TPP-PA), (2) ammonium hydroxide + phosphoric acid (TPP-NH 4 OH), (3) diammonium phosphate (TPP-DAP), (4) tetramethylammonium sulphate + phosphoric acid (TPP-TMAP), and (5) tetrabutylammonium phosphate (TPP-TBAP), where a maximum conductivity of 88 mS cm -1 at 200 °C was obtained for TPP prepared from the TBAP precursor. TPP prepared from all of the different precursors formed the crystalline cubic Pa-3 with combining macron] phase after sintering at 650 °C for 2.5 hours. Furthermore, TPP-TBAP/Nafion® composite membranes prepared with a 90 : 10 ratio exhibited an OCV of 0.98 V and produced a maximum peak power density (PPD) of 630 mW cm -2 at an operating temperature of 220 °C. Our results demonstrate the significant impact of the TPP precursor on proton conductivity and fuel cell performance.

36 MATERIALS SCIENCE↗