Search NASA⌕ Search

Engineering topics

Serrano, M.

Publications and source records attributed to Serrano, M..

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Performance of multifunctional piezoelectric energy harvesting microgyroscopes with material degradation

Most microelectromechanical systems (MEMS) are made from brittle materials that are prone to cracking. Damage from the formation of cracks can occur anytime during the manufacturing process or due to mechanical loading of MEMS devices. Cracks can increase the structures flexibility and lead to changes in performance or total failure. Understanding the potential influences cracks in MEMS is necessary for the longevity of these systems. The energy harvesting microgyroscope studied in this work is susceptible to crack propagation in its silicon substrate and lead zirconate titanate piezoelectric patch. To this end, an electromechanical model is developed to capture the impacts of cracks on the performance of a damaged energy harvesting microgyroscope. Numerical methods are used to approximate the damage associated with distributed crack networks. Then, the static and dynamic responses of the damaged microgyroscope are analyzed for two possible multifunctional setups. Here, the current study revealed that cracks can significantly affect the static and dynamic behaviors of the microgyroscope energy harvester. Combinations of cracking and piezoelectric property degradation cause a decrease in the static pull-in voltage and shift the resonance frequencies of the system. Additionally, it is shown that the systems sensitivity to changes in the base rotation and energy harvesting capabilities vary widely depending on the severity of material degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Broadband piezoelectric energy harvesting microgyroscopes: Design and nonlinear analysis

Small devices in remote or difficult-to-reach areas can benefit from harvesting energy from mechanical wasted energy, which reduces the requirement for a new power source. A multi-purpose energy harvesting microgyroscope system based on piezoelectric materials is suggested. The necessity of taking spatially varying electrostatic forces is examined. Considering the effects of the system's width and thickness, DC voltage, and angular speed the systems inherent frequencies are found. The partial differential equations describing the system's dynamics are numerically solved by using the differential quadrature method. Further, the numerical analysis enables to identify the optimal system design for broadband energy harvesting. The simulation results reveal that a system with a non-symmetric beam design is adequate for broadband energy harvesting. This is associated with the applied DC voltage, which may be modified to improve the broadband frequency of the system. It is concluded that the nonlinear softening effects create a broadband frequency response with high voltage output. However, DC and AC voltages need to be carefully selected in order to avoid the dynamic pull-in.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

A NEA review on innovative structural materials solutions, including advanced manufacturing processes for nuclear applications based on technology readiness assessment

The Nuclear Energy Agency (NEA) Expert Group on Innovative Structural Materials (EGISM) was established in 2008 under the guidance of the Nuclear Science Committee (NSC). Its objectives are to conduct joint and comparative studies to support the development, selection and characterisation of innovative structural materials that can be implemented in advanced nuclear fuel cycles, under long service lifetime and extreme conditions, such as high temperature, high dose/dose rate and corrosive chemical environments. In this context of growing interest and initiatives, the EGISM initiated at the beginning of 2018 an activity among its members to: Identify, in a non-exhaustive way, the currently existing programs on innovative materials and fabrication processes in NEA member countries and China; Establish a first cartography of the activities that are underway on these topics and identify common subjects and thematic; Propose a Technology Readiness Level scale to estimate the maturity of both innovative materials and fabrication processes; Carry out a reflection on what the enablers are to quickly climb this TRL scale, as well as the obstacles, in order to identify solutions to overcome them. This paper first gives definitions shared between the EGISM members on what are considered as advanced structural materials solutions. Next, some international initiatives for the accelerated development of high performance materials are presented both in non-nuclear and nuclear fields. Then, the methodology adopted for technology readiness assessment is explained. A non-exhaustive synthesis of the projects identified among the EGISM members on innovative structural materials and advanced manufacturing solutions such as additive manufacturing is presented. The TRL level of these projects is evaluated. A focus is also made on some of these projects to illustrate and explain the TRLs chosen as well as highlighting enablers or obstacles identified to climbing up the TRL scale.

36 MATERIALS SCIENCE↗