Engineering topics

Serrano, Marta

Publications and source records attributed to Serrano, Marta.

5 records

DOE OSTI2023

Creep strength boosted by a high-density of stable nanoprecipitates in high-chromium steels

There is a need worldwide to develop materials for advanced power plants with steam temperatures of 700°C and above that will achieve long-term creep-rupture strength and low CO 2 emissions. The creep resistance of actual 9-12Cr steels is not enough to fulfil the engineering requirements above 600°C. In this paper, the authors report their advances in the improvement of creep properties of this type of steels by the microstructural optimization through nano-precipitation using two methodologies. 1) Applying a high temperature austenitization cycle followed by an ausforming step (thermomechanical treatment, TMT) to G91 steel, to increase the martensite dislocation density and, thus, the number density of MX precipitates (M = V,Nb; X = C,N) but at the expense of deteriorating the ductility. 2) Compositional adjustments, guided by computational thermodynamics, combined with a conventional heat treatment (no TMT), to design novel steels with a good ductility while still possessing a high number density of MX precipitates, similar to the one obtained after the TMT in G91. The microstructures have been characterized by optical, scanning and transmission electron microscopy, EBSD and atom probe tomography. The creep behaviour at 700°C has been evaluated under a load of 200 N using small punch creep tests.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Influence of fatigue precracking and specimen size on Master Curve fracture toughness measurements of EUROFER97 and F82H steels

EUROFER97 and F82H steels are two leading reduced-activation ferritic-martensitic (RAFM) steels for fusion first wall and blanket applications. Exposure to the harsh environment of fusion reactors can result in severe degradation of fracture toughness. Thus, the post-irradiation evaluation of fracture toughness is critical for understanding the material behavior. Due to the space constraints of irradiation facilities and challenges in controlling a uniform irradiation condition for large size specimens, the development of small specimen test techniques (SSTT) is indispensable to evaluate the performance of irradiated materials. In this study, we evaluated specimen size effects on the Master Curve fracture toughness of EUROFER97 and F82H steels. A wide variety of specimens, including 0.5 T compact tension (C(T)) specimens, 0.16 T mini-compact tension (miniC(T)) specimens, and 1.65 mm miniature bend bar specimens, were tested. The testing methodology was based on the Master Curve method in the ASTM E1921 standard. No specimen size effect was observed in 0.5 T C(T) and 0.16 T miniC(T) specimens on the Master Curve reference temperature T0, while 1.65 mm miniature bend bar specimens yielded a higher T 0Q . A strong effect of fatigue precracking on T 0 for 0.5 T C(T) and 0.16 T miniC(T) specimens was observed, such that testing on specimens with skewed fatigue precrack fronts resulted in lower T 0 than for specimens with ASTM standard qualified straight fatigue precrack fronts. The results highlight the importance of experimental quality control in developing SSTT for Master Curve fracture toughness testing. Lastly, we also evaluated and provided recommendations on the minimum number of specimens needed for each specimen type for yielding reliable T 0Q values.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Longitudinal SARS-CoV-2 seroprevalence in Portugal and antibody maintenance 12 months after infection

During the COVID-19 pandemic, Portugal has experienced three distinct SARS-CoV-2 infection waves. We previously documented the prevalence of SARS-CoV-2 immunity, measured by specific antibodies, in September 2020, 6 months after the initial moderate wave. Here, we show the seroprevalence changes 6 months later, up to the second week of March 2021, shortly following the third wave, which was one of the most severe in the world, and 2 months following the start of the vaccination campaign. A longitudinal epidemiological study was conducted, with a stratified quota sample of the Portuguese population. Serological testing was performed, including ELISA determination of antibody class and titers. The proportion of seropositives, which was 2.2% in September 2020, rose sharply to 17.3% (95% CI: 15.8–18.8%) in March 2021. Importantly, circulating IgG and IgA antibody levels were very stable 6 months after the initial determination and up to a year after initial infection, indicating long-lasting infection immunity against SARS-CoV-2. Moreover, vaccinated people had higher IgG levels from 3 weeks post-vaccination when compared with previously infected people at the same time post-infection.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Prevalence of SARS-CoV-2 Antibodies after First 6 Months of COVID-19 Pandemic, Portugal

In September 2020, we tested 13,398 persons in Portugal for antibodies against severe acute respiratory syndrome coronavirus 2 by using a quota sample stratified by age and population density. We found a seroprevalence of 2.2%, 3–4 times larger than the official number of cases at the end of the first wave of the pandemic.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Guidelines for IAEA Small Specimen Test Techniques Master Curve Fracture Toughness Testing

Under the auspices of International Atomic Energy Agency (IAEA), a coordinated research project (CRP) entitled “Towards the Standardization of Small Specimen Test Techniques for Fusion Applications” has started since 2017. The overall objective of the project is to provide a set of guidelines for small specimen test techniques (SSTT) based on commonly agreed best practices on main test techniques including tensile, creep, low cycle fatigue, fracture toughness, and fatigue crack growth rate. This will act as the first step of a full standardization of the SSTT. Fusion structural materials, i.e., reduced activation ferritic/martensitic (RAFM) steels, are used for testing. In addition, the project will create a comprehensive mechanical property database of RAFM steels tested by SSTT. For the fracture toughness task of the CRP, three testing methods including Master Curve, local approach for ductile crack growth and cleavage fracture, and ductile approach at room temperature will be evaluated. This report focuses on developing guidelines for the round-robin Master Curve testing based on the ASTM standard E1921-19b “Standard Test Method for Determination of Reference Temperature, T 0 , for Ferritic Steels in the Transition Range” and commonly agreed best practice from researchers at Oak Ridge National Laboratory (ORNL), Centre for Energy, Environment and Technology (CIEMAT), and UK Atomic Energy Authority (UKAEA).

36 MATERIALS SCIENCE↗