Search NASA⌕ Search

Engineering topics

Seshadri, Arunkumar

Publications and source records attributed to Seshadri, Arunkumar.

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Development of hydrothermal corrosion model and BWR metal coating for CVD SiC in light water reactors

SiC/SiC fiber composites with CVD SiC overcoats are potential candidates for light water reactor advanced accident tolerant cladding materials. Understanding its corrosion kinetics in Light Water Reactor (LWR) conditions is essential to evaluate the concept's viability. Existing models only account for the temperature and oxygen concentration effect on the hydrothermal corrosion behavior applicable to LWR operating conditions. However, the development of a general corrosion rate for CVD SiC that accounts for the impact of irradiated microstructure, flow rate, electrical resistivity, pH, and surface roughness is critical for the practical realization of SiC/SiC-based cladding concepts. After a rigorous experimental campaign, this work updates the existing hydrothermal corrosion model to predict hydrothermal corrosion in LWRs. Numerical radiation and coolant chemistry analysis for LWRs conducted based on the updated corrosion kinetic models suggests that CVD SiC is likely a viable environmental barrier coating for Pressurized Water Reactors while questionable for Boiling Water Reactors (BWR) when the effect of irradiation damage on SiC corrosion is considered. An effective mitigation strategy for the double-layer metal coating is proposed for BWR applications. The double-layer metal coating comprising a FeCrAl overcoat with an intermediate Cr bond coating was observed to provide a stable protective barrier against SiC dissolution in BWR conditions. Finally, the proposed metal coating was also fully adherent following quench and burst tests.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Why ionizing radiation enhances surface wettability

Radiation-Induced Surface Activation is an inherent phenomenon where surfaces that are exposed to gamma irradiation are observed to undergo an increase in wettability. This increase in wettability as a result of the ionizing radiation exposure has so far been demonstrated to have a pronounced impact on Leidenfrost temperature and two-phase fluid dynamics. Test results from previous experiments have shown that incorporation of this effect on heat transfer equipment design may increase the thermal-hydraulic margin leading to higher thermal efficiency. However, the mechanism behind the increased wettability is not clearly understood. In the present work, three different materials (Zircaloy-4, 316 stainless steel, and copper) were exposed at two different dose rates with use of two different gamma irradiation facilities. A detailed surface characterization on the post-irradiated samples is carried out to understand the changes in surface chemistry, wettability and surface morphology. It is observed from the experiments that the increase in wettability upon irradiation depended on the total dose and not on the dose rate. Moreover, localized oxidation and porosity induced by radiolysis was seen to be the predominant mechanism behind increased wettability which leads to improved Leidenfrost temperature.

36 MATERIALS SCIENCE↗