Search NASA⌕ Search

Engineering topics

Setterfield, Timothy P

Publications and source records attributed to Setterfield, Timothy P.

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Landing Site Selection with a Variable-Resolution SLAM-Refined Map

In many scenarios it is desirable for planetary landers to select or modify their landing sites autonomously during descent. We present a landing site selection algorithm which is optimized to work in conjunction with a Simultaneous Localization and Mapping system. Our algorithm selects landing sites based on site slope, roughness, and operator-defined interest. In addition, we generate guidance commands and approximate fuel consumption for the highest ranked sites. We validate our algorithm with LiDAR and inertial data gathered by a vertical take-off and landing vehicle.

Chen, Po-Ting↗
NASA NTRS2022

Real-World Testing of LiDAR-Inertial Based Navigation and Mapping for Precision Landing

The fusion of LiDAR and inertial measurements duringspacecraft descent and landing can be used to estimate alander’s navigation state and map the terrain below. Together,these data products can be used to enable safe and preciselanding on celestial bodies for which a priori orbital reconnaissanceis insufficient for hazard detection and avoidance.Unlike camera images used in visual terrain relative navigation,LiDAR scans are insensitive to changes in illumination; as aresult, the technique can be used to land in poorly lit areas,or at times of day when the lighting conditions are incongruentwith existing orbital imagery. In this paper, we extend previouswork in which we introduced a factor graph based smoothingapproach for LiDAR-inertial navigation and mapping. Whereasthe algorithms were previously tested on simulated data, thispaper presents testing on real-world data. Data from theAutonomous Landing Hazard Avoidance Technology (ALHAT)airplane flight tests in the Yucca Flats and Death Valley in2009 (FT3), the Morpheus vertical take off and landing flighttests at Kennedy Space Center in 2014 (FT6), and the landingof Perseverance and Ingenuity on Mars in 2021 (M2020) wereused to evaluate algorithm performance. In this paper, weextend our LiDAR-inertial technique to work with a variety ofranging technologies: single point laser altimetry (FT3), denseflash LiDAR (FT6), and six-beam radar (M2020). A thoroughperformance analysis for all three datasets is presented. Datasetpreparation, improvements in algorithm robustness, and outlierrejection, which were necessitated by the transition to realworlddata, are discussed.

Trawny, Nikolas↗
NASA NTRS2021

LiDAR-Inertial Based Navigation and Mapping for Precision Landing

Future lander missions will travel to ambitious, scientifically interesting locations near rough and dangerous terrain. They will need to operate with limited prior information about the terrain, and under varying lighting conditions. Landing safely and precisely in the face of these challenges is difficult for existing vision-based landing systems, which require detailed orbital reconnaissance, a priori hazard maps, and impose time-of-day restrictions on landing to ensure similar lighting conditions in orbital and descent imagery. Advanced 3D imaging LiDAR systems currently under development, and originally intended for single-scan hazard detection, have the potential to be operated continuously from altitudes of up to 5 km. Used together with existing inertial measurement units (IMUs), these sensors open a path-to-flight for a full navigation and mapping system, which could replace or augment a traditional landing sensor suite. A landing system based around these sensors can perform accurate altimetry, map-relative localization (MRL), LiDAR-inertial odometry, and map refinement in an illumination-insensitive manner, over unknown or partially known terrain. This paper outlines preliminary work on a LiDAR-inertial landing system that: estimates the spacecraft trajectory during entry, descent, and landing (EDL); and maps the topography of the terrain below, for future use in hazard detection and avoidance. An incremental, factor graph based, smoothing approach is used to solve for the maximum a posteriori trajectory of spacecraft states. Integrated IMU measurements and features tracked in adjacent range and intensity images are used to estimate motion (LiDAR-inertial odometry). LiDAR scans are binned into motion-corrected digital elevation models (DEMs), which are matched to an existing orbital topographic map to provide absolute position information (MRL). The estimated trajectory is then used to project the LiDAR scans into the map frame, creating a variable-resolution quadtree topographic map suitable for hazard detection and avoidance. Existing topographic maps from throughout the solar system (i.e., Earth, the Moon, Mars, Ceres, Vesta, Europa, Enceladus, and Eros) are upsampled for use in EDL simulations. The Mars 2020 Lander Vision System Simulator (LVSS) is extended to simulate LiDAR-inertial data for realistic EDL trajectories. Results of the algorithm operating on the simulated data are presented. Estimated spacecraft trajectory and refined map are compared to ground truth to assess estimation accuracy.

Katake, Anup↗
NASA NTRS2020

Multibody Simulation of REMORA CubeSat Docking to and Pushing a Spent Rocket Booster

This paper details the multibody simulation of three phases of critical importance to the feasibility of the REMORA CubeSat space debris mitigation concept: the final approach of the CubeSat to a spent rocket booster; the grappling of the spent rocket booster using a robotic arm; and the pushing of the spent rocket booster to divert its course from another on-orbit asset. The extension of a robotic mobility and manipulation modeling toolkit (M3TK) from multibody dynamics simulation of manipulators and ground vehicles to simulation of orbital robotics is outlined. This includes the identification of the appropriate parameters required to concisely and generically describe thruster loads, thruster mixing, spacecraft control, and spacecraft navigation for the purpose of on-orbit robotics simulation. A high-level spacecraft navigator commands maneuvers to target spacecraft states. A PID spacecraft controller takes the target states and calculates desired forces and torques. A thruster mixer solves a quadratic program to determine the optimal thruster firing times for the propulsion system. Pulse width modulated actuation of eight canted cold gas thrusters is used in the simulated approach to a rocket nozzle from a distance of 200 m. A five degree of freedom robotic arm is controlled to position a pair of pincers to grasp the rocket nozzle. Contact dynamics are used to accurately simulate the grasping of the rocket nozzle by the pincers. A similar, but separate simulation is performed to assess the ability of the REMORA CubeSat to push the large spent rocket booster. This diversion maneuver makes use of an additional, larger thruster, and pushes the rocket booster in excess of 400 m. Appropriate motor control gains on the robotic arm are found to be higher during the pushing phase than those which are appropriate during free motion; this increase promotes rigidity of the arm and allows it to properly direct the pushing force. Challenges encountered in time step selection for numerical stability of the simulation are also discussed.

Mukherjee, Rudranarayan↗