Mach number effects on conical surface features of swept shock-wave/boundary-layer interactions
Explore the source record for details and available documents.
Lu, F. K.↗
Engineering topics
Settles, G. S.
Publications and source records attributed to Settles, G. S..
Laser skin friction measurements and CFD comparison of weak-to-strong swept shock/boundary-layer interactions
A joint experimental and computational study of skin friction in weak-to-strong swept shock wave/turbulent boundary-layer interactions has been carried out. A planar shock wave is generated by a sharp fin at angles of attack alpha = 10 deg and 16 deg at M(infinity) = 3 and 16 and 20 deg at M(infinity) = 4. Measurements are made using the Laser Interferometer Skin Friction meter, which optically detects the rate of thinning of an oil film applied to the test surface. The results show a systematic rise in the peak c(f) at the rear part of the interaction, where the separated flow atttaches. For the stronget case studied, this peak is an order of magnitude higher than the incoming freestream c(f)level.
Kim, K.-S.↗
An experimental study of the effect of streamwise vorticity on supersonic mixing enhancement
An initial experimental study of the effect of streamwise vorticity on supersonic turbulent mixing has been carried out. A Mach 3 streamwise vortex is generated using a strutmounted swirl injector and is injected into a Mach 3.5 freestream. The resulting flowfield is investigated using both five-hole angularity probe and total temperature probe surveys. The results are compared to identical experiments with a baseline, swirl-free Mach 3 jet. Laser Light Sheet (LLS) images are used to observe the mixing phenomena. The entrainment of energy and mass is used to evaluate the degree of mixing between the two streams for both the vortex and jet cases. The results reveal that streamwise vorticity does lead to a modest mixing enhancement of about 34 percent for the conditions tested.
Naughton, J. W.↗
Skin-friction measurements by laser interferometry
The measurement of skin friction in rapidly distorted compressible flows is difficult, and very few reliable techniques are available. A recent development, the laser interferometer skin friction (LISF) meter, promises to be useful for this purpose. This technique interferometrically measures the time rate of thinning of an oil film applied to an aerodynamic surface. Under the proper conditions the wall shear stress may thus be found directly, without reference to flow properties. The applicability of the LISF meter to supersonic boundary layers is examined experimentally. Its accuracy and repeatability are assessed, and conditions required for its successful application are considered.
Kim, K.-S.↗
An experimental study of shock wave/vortex interaction
The interaction of a supersonic streamwise vortices (of Mach number 2.2, 3.0, and 3.5) with a normal shock wave has been experimentally investigated, and is found to be highly unsteady. Five-hole pressure-probe and temperature measurements ahead of the interaction are used as initial conditions for an axisymmetric Navier-Stokes calculation. The numerical results supports the hypothesis that supersonic vortex breakdown is an important factor in the observed interaction flow pattern.
Metwally, O. M.↗
Measurements of a supersonic turbulent vortex
Mean-flow measurements of a supersonic turbulent streamwise vortex are presented. This vortex was produced by the injection of a swirling flow along the centerline of a supersonic airstream at Mach 3. Directional Mach number distributions, obtained via a five-hole flow-angularity probe, reveal vortex characteristics similar to those of the incompressible case, even though rotational Mach numbers up to 0.8 were obtained. This work is the first step of a study of the supersonic vortex breakdown phenomenon.
Metwally, O. M.↗
Mach number effects on conical surface features of swept shock boundary-layer interactions
A joint experimental and computational study is made of the shock-wave turbulent boundary-layer interaction generated by sharp fins, with emphasis on Mach-number effects. The Mach number range is from 2 to 4 and the unit Reynolds number is from 50 to 80 million per meter. Fin angles are varied from 4 to 22 deg. Surface-flow patterns are obtained using a color surface-flow-visualization technique. The results show that the upstream-influence response in the conical far-field region is a function of the freestream Mach number and the shock strength. A new interpretation of the behavior of the upstream influence with changes of the inviscid shock angle is given. Agreement between the experimental and the computed upstream-influence lines becomes poorer for stronger interactions, with the computations underpredicting the upstream-influence line.
Lu, F. K.↗
Recent skin friction techniques for compressible flows
A brief review is given of developments over the last decade in techniques for the measurement of skin friction in compressible airflows. Emphasis is placed on mean measurements beneath turbulent boundary layers in the supersonic and hypersonic flow regimes. Recent improvements in existing techniques such as the skin friction balance, Preston tube, sublayer fence, and heat transfer analogy are discussed. New or potential techniques including optical and acoustic measurements are also treated. Finally, new results are presented on the adaptation of the recently-developed laser interferometer skin friction meter for use in high-speed wind tunnels.
Settles, G. S.↗
Experimental and computational study of a swept compression corner interaction flowfield
Explore the source record for details and available documents.
Settles, G. S.↗
On the inception lengths of swept shock-wave/turbulent boundary-layer interactions
Experimental data are shown for the inception lengths of swept compression corner-generated and fin-generated shock/boundary layer interactions at Mach 2.95. These results are found to correlate on the basis of three different flow regimes. The inception lengths of these flows are dominated by a singularity at the cylindrical/conical boundary for swept corners and by an elongation due to shock wave sweepback for fin interactions. Similarity rules for both Re(delta)and shock generator geometry effects on inception lengths are demonstrated.
Settles, G. S.↗
Conical similarity of shock/boundary-layer interactions generated by swept and unswept fins
A parametric experimental investigation has been made of the class of three-dimensional shock wave/turbulent boundary layer interactions generated by swept and unswept leading-edge fins. The fin sweepback angles were 0-65 deg at 5, 9, and 15 deg angles of attack. Two equilibrium two-dimensional turbulent boundary layers with a freestream Mach number of 2.95 and a Reynolds number of 6.3 x 10 to the 7th/m were used as incoming flow conditions. All of the resulting interactions were found to possess conical symmetry of the surface flow patterns and pressures outside of an initial inception zone. Further, these interactions were found to obey a simple conical similarity rule based on inviscid shock wave strength, irrespective of fin sweepback or angle of attack. This is one of the first demonstrations of similarity among three-dimensional interactions produced by geometrically dissimilar shock generators.
Settles, G. S.↗
Flowfield scaling of a swept compression corner interaction A comparison of experiment and computation
Over the past decade, there has been some important progress in understanding the problems of three-dimensional (3D) shock wave/turbulent boundary layer interactions. However, the problems are by no means solved. The present investigation has the objective to determine the flowfield structure of a swept compression corner interaction and to perform a test of an equation considered by Settles and Bogdonoff (1982). The experimental data obtained in a 20 x 20 cm high Reynolds number supersonic wind tunnel are compared with the predictions of a state-of-the-art numerical solution of the Navier-Stokes equations. It is found that a 3D scaling law for Reynolds number effects, previously established for interaction 'footprints', is equally valid when applied to the present flowfield.
Settles, G. S.↗
Conical similarity of shock/boundary layer interactions generated by swept fins
A parametric experimental study has been made of the class of 3D shock wave/turbulent boundary layer interactions generated by swept-leading-edge fins. The fin sweepback angles ranged from 0 to 65 deg at angles of attack of 5, 9, and 15 deg. Two equilibrium 2D turbulent boundary layers with a free-stream Mach number of 2.95 and a Reynolds number of 6.3 x 10 to the 7th/m were used as incoming flow conditions. All the resulting interactions were found to possess conical symmetry of surface pressures and skin friction lines beyond an initial inception zone. Further, these interactions revealed a simple similarity based on inviscid shock strength irrespective of fin sweepback or angle of attack.
Lu, F. K.↗
An experimental study of three-dimensional shock wave/boundary layer interactions generated by sharp fins
The interaction between a turbulent boundary layer and a shock wave generated by a sharp fin with leading edge sweepback was investigated. The incoming flow was at Mach 2.96 and at a unit Reynolds number of 63 x 10 to the 6th power 0.1 m. The approximate incoming boundary layer thickness was either 4 mm or 17 mm. The fins used were at 5 deg, 9 deg and 15 deg incidence and had leading edge sweepback from 0 deg to 65 deg. The tests consisted of surface kerosene lampblack streak visualization, surface pressure measurements, shock wave shape determination by shadowgraphs, and localized vapor screen visualization. The upstream influence lengths of the fin interactions were correlated using viscous and inviscid flow parameters. The parameters affecting the surface features close to the fin and way from the fin were also identified. Essentially, the surface features in the farfield were found to be conical.
Lu, F. K.↗
The state of the art of conventional flow visualization techniques for wind tunnel testing
Conventional wind tunnel flow visualization techniques which consist of surface flow methods, tracers, and optical methods are presented. Different surface flow methods are outlined: (1) liquid films (oil and fluorescent dye and UV lighting, renewable film via porous dispenser in model, volatile carrier fluid, cryogenic colored oil dots, oil film interferometry); (2) reactive surface treatment (reactive gas injection, reversible dye); (3) transition and heat transfer detectors (evaporation, sublimation, liquid crystals, phase change paints, IR thermography); and (4) tufts (fluorescent mini tufts, cryogenic suitability). Other methods are smoke wire techniques, vapor screens, and optical methods.
Settles, G. S.↗
Compressible turbulent boundary layer interaction experiments
Four phases of research results are reported: (1) experiments on the compressible turbulent boundary layer flow in a streamwise corner; (2) the two dimensional (2D) interaction of incident shock waves with a compressible turbulent boundary layer; (3) three dimensional (3D) shock/boundary layer interactions; and (4) cooperative experiments at Princeton and numerical computations at NASA-Ames.
Settles, G. S.↗
A reattaching free shear layer in compressible turbulent flow - A comparison of numerical and experimental results
An investigation of a two-dimensional, free turbulent shear layer reattaching on an inclined surface at Mach 2.92 and at a high Reynolds number is described. The test geometry is specifically designed to isolate the reattachment process of a high-speed separated flow. A numerical solution of the time-dependent, Reynolds-averaged, Navier-Stokes equations for the entire flow field, employing a two-equation eddy viscosity turbulence model, is presented. Detailed comparisons of prediction and experiment are made in the free shear layer, at reattachment, and in the developing boundary layer downstream. These comparisons include mean surface quantities as well as mean and fluctuating flowfield quantities. Although the overall features of this complex flow field are predicted, there are several deficiencies in the numerical solution, particularly in the region downstream of reattachment. Modifications of the turbulence model to correct these deficiencies are discussed.
Horstman, C. C.↗
A Reattaching Free Shear Layer in Compressible Turbulent Flow: A Comparison of Numerical and Experimental Results
An investigation of the two-dimensional, free turbulent shear layer reattaching on an inclined surface at Mach 2.92 and at a high Reynolds number is described. The test geometry is specifically designed to isolate the reattachment process of a high-speed separated flow. A numerical solution of the time-dependent, Reynolds-averaged, Navier-Stokes equations for the entire flow field, employing a two-equation eddy viscosity turbulence model, is presented. Detailed comparisons of prediction and experiment are made in the free shear layer, at reattachment, and in the developing boundary layer downstream. These comparisons include mean surface quantities as well as mean and fluctuating flow-field quantities. Although the overall features of this complex flow field are predicted, there are several deficiencies in the numerical solution, particularly in the region downstream of reattachment. Modifications of the turbulence model to correct these deficiencies are discussed.
Horstman, C. C.↗