Engineering topics

Sewall, W. G.

Publications and source records attributed to Sewall, W. G..

14 records

NASA NTRS1989

Simultaneous detection of separation and transition in surface shear layers

Flush-mounted hot-film gages have proved effective in detecting boundary-layer transition and in measuring skin friction but with limited success in detecting laminar separation and reattachment. The development of multielement micro hot-film sensors, and the recent discovery of the phase reversal phenomena associated with low-frequency dynamic shear stress signals across regions of laminar separation and turbulent reattachment, have made it possible to simultaneously and unambiguously detect these surface shear layer characteristics. Experiments were conducted on different airfoils at speeds ranging from low subsonic to transonic speeds to establish the technique for incompressible and compressible flow applications. The multielement dynamic shear stress sensor technique was successfully used to detect laminar separation, turbulent reattachment, as well as, shock induced laminar and turbulent separation.

Mangalam, Siva M.↗

NASA NTRS1988

A new multipoint thin-film diagnostic technique for fluid dynamic studies

A multielement hot-film sensor has been developed with closely-spaced elements (2.5 mm) in the streamwise direction. In addition to boundary-layer transition detection, the output of these sensors can reveal the locations of boundary-layer separation and reattachment by a 180 deg phase difference in the 0-200-Hz frequency bandwidth between sensor elements on each side of either the separation or reattachment point. This paper describes the features of multielement hot-film sensor arrays and discusses results from their application to a number of low-speed and transonic airfoil tests.

Sewall, W. G.↗

NASA NTRS1987

Designing transonic wind-tunnel test sections for flow diagnostics and laser velocimeter applications

The design, fabrication, and validation of the Basic Aerodynamic Facility (BARF), developed for the direct comparison of three-dimensional laser velocimetry (LV) and hot-wire techniques at transonic speeds, are discussed. To accommodate the installation of the three-dimensional orthogonal LV system in the BARF, the transonic slots were redesigned to house windows, and the test section mounting was redesigned to facilitate LV transversing. Two-dimensional and three-dimensional code validation tests of the LV test section showed uniform mean flow through the test section to sonic speeds, and fluctuating pressure measurements at subsonic speeds which are consistent with facilities with good flow quality.

Jones, G. S.↗

NASA NTRS1987

Wind-tunnel test results of airfoil modifications for the EA-6B

Wind-tunnel tests have been conducted (to determine the effects on airfoil performance for several airfoil modifications) for the EA-6B Wing Improvement Program. The modifications consist of contour changes to the leading-edge slat and trailing-edge flap to provide a higher low-speed maximum lift with no high-speed cruise-drag penalty. Airfoil sections from the 28- and 76-percent span stations were selected as baseline shapes with the major testing devoted to the inboard airfoil section (28-percent span station). The airfoil modifications increased the low-speed maximum lift coefficient between 20 and 35 percent over test conditions of 3 to 14 million chord Reynolds number and 0.14 to 0.34 Mach number. At the high-speed test conditions of 0.4 to 0.80 Mach number and 10 million chord Reynolds number, the modified airfoils had either matched or had lower drag coefficients for all normal-force coefficients above 0.2 as compared to the baseline airfoil. At normal-force coefficients less than 0.2, the baseline (original) airfoil had lower drag coefficients than any of the modified airfoils.

Sewall, W. G.↗

NASA NTRS1984

Wall pressure measurements for three-dimensional transonic tests

An experiment is described that provides input data for wind-tunnel wall interference assessment methods that are based on test-section wall pressure distributions. Wall pressures have been measured along orifice rows on the test-section walls during longitudinal force tests on two model sizes of the same configuration. These data were acquired at Mach numbers between 0.60 and 0.90 in a small, atmospheric transonic wind tunnel. A sample of the data and a discussion of results are presented.

Sewall, W. G.↗

NASA NTRS1983

Support-sting interference on boattail pressure drag for Reynolds numbers up to 70 x 10 to the 6th

A model was tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel to investigate the effects of Reynolds number on boattail pressure drag for a variety of sting shapes. The boattail pressure drag for constant Mach number increased linearly with Reynolds number over the Reynolds number range tested. The data indicated that, as the disturbance produced by the sting on the boattail increased, the boattail pressure drag became less sensitive to Reynolds number change. Also, it was found that the model base pressure versus Reynolds number curve reached a plateau within the Reynolds number range examined.

Gloss, B. B.↗

NASA NTRS1982

Similarity rules for effects of sidewall boundary layer in two-dimensional wind tunnels

A simple analysis of the interaction of the model pressure field with the boundary layer on an unventilated wind tunnel wall is presented. It is shown that the effects of this interaction are similar to compressibility effects for sidewall boundary layers in two dimensional wind tunnels. This similarity is used to derive modified forms of the Prandtl Glauert rule for subsonic flow and the von Karman rule for transonic flow which are validated by comparison with experimental data. The three dimensional interaction problem is discussed, and it is shown that model pressure field/wall boundary layer interaction effects are not similar to compressibility effects in three dimensional wind tunnels.

Barnwell, R. W.↗

NASA NTRS1982

Application of a transonic similarity rule to correct the effects of sidewall boundary layers in two-dimensional transonic wind tunnels

A transonic similarity rule which accounts for the effects of attached sidewall boundary layers is presented and evaluated by comparison with the characteristics of airfoils tested in a two dimensional transonic tunnel with different sidewall boundary layer thicknesses. The rule appears valid provided the sidewall boundary layer both remains attached in the vicinity of the model and occupies a small enough fraction of the tunnel width to preserve sufficient two dimensionality in the tunnel.

Sewall, W. G.↗

NASA NTRS1981

Two-dimensional aerodynamic characteristics of an airfoil designed for two

An airfoil designed for helicopter rotor application is investigated. The airfoil is designed to increase maximum normal force coefficient while maintaining favorable drag divergence and pitching moment characteristics. Two modifications are also tested. Maximum normal force coefficient varies from 1.14 to 0.90 at Mach numbers from about 0.35 to 0.65. Both modifications decreased drag coefficient at zero normal force coefficient for Mach numbers near drag divergence, but were less beneficial at a normal force coefficient of -0.2.

Bingham, G. J.↗

NASA NTRS1981

The effects of sidewall boundary layers in two-dimensional subsonic and transonic wind tunnels

A transonic similarity rule which accounts for the effects of attached sidewall boundary layers in two-dimensional wind tunnels is presented along with results of an experimental investigation of sidewall boundary-layer effects. The rule appears valid provided the sidewall boundary layer both remains attached in the vicinity of the model and occupies a small enough fraction of the tunnel width to avoid substantial three-dimensional interaction with the model.

Sewall, W. G.↗

NASA NTRS1981

Description of recent changes in the Langley 6- by 28-inch transonic tunnel

Calibrations were obtained in the Langley 6 by 28-inch transonic tunnel with newly installed controllable reentry flaps and test section floor and ceiling. Using available theory, the top and bottom slotted walls were redesigned for minimum wind tunnel interference errors of blockage and stream-line curvature. To minimize Mach number gradients along the tunnel axis downstream of the model, controllable flaps were installed to regulate the flow reentering the test section through the slotted walls. The flap setting is independent of stagnation pressure and varies only with Mach number. The freestream Mach number is determined from the pressrue measured at a station 66.04 cm upstream of the model station. The model has no significant influence on the vertical Mach number distribution at this station. This method of Mach number determination appears to be more accurate than one using the plenum pressure.

Sewall, W. G.↗

NASA NTRS1979

Design and calibration of slotted walls for transonic airfoil wind tunnels

The traditional procedure for estimating the performance of slotted walls for airfoil wind tunnels is reviewed, and a modification which improves the accuracy of this procedure is described. Unlike the traditional procedure, the modified procedure indicates that the design of airfoil wind-tunnel walls which induce minimal blockage and streamline-curvature effects is feasible. The design and testing of such a slotted wall is described. It is shown experimentally that the presence of a model can affect the plenum pressure and thus make the use of the plenum pressure as a calibration reference questionable. Finally, an ONERA experiment which shows the effect of the sidewall boundary layer on the measured model normal force is discussed.

Barnwell, R. W.↗

NASA NTRS1977

Low-speed wind tunnel tests of 1/9-scale model of a variable-sweep supersonic cruise aircraft

Tests were conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics at low subsonic speeds of a 1/9-scale model of a variable-sweep supersonic cruise aircraft. The model configurations investigated were the basic unflapped arrangement, a take-off flap arrangement, and a landing flap arrangement with several strake leading-edge flow control devices. The tests were conducted at angles of attack from about -5 to 36 deg, sideslip angles from -5 to 10 deg.

Mclemore, H. C.↗

NASA NTRS1974

Low speed wind tunnel tests of a 1/9-scale model of a variable-sweep advanced supersonic transport

Tests have been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics of a 1/9-scale variable-sweep advanced supersonic transport configuration. The model configurations investigated were the basic unflapped arrangement, and a takeoff and landing flap arrangement with several strake leading edge flow control devices. The tests were conducted for an angle-of-attack range from about minus 5 deg to 36 deg and a sideslip range from minus 5 deg to 10 deg. The tests were conducted for a range of Reynolds number from 3.92 million to 5.95 million corresponding to test velocities of about 54.5 knots and 81.7 knots, respectively.

Mclemore, H. C.↗