Search NASA⌕ Search

Engineering topics

Sexton, Daniel

Publications and source records attributed to Sexton, Daniel.

DEMONSTRATION OF 3D EFFECTS WITH HIGH GAIN AND EFFICIENCY IN A UV FEL OSCILLATOR

We report on the performance of a high gain UV FEL oscillator operating on an energy recovery linac at Jefferson Lab. The high brightness of the electron beam leads to both gain and efficiency that cannot be reconciled with a one-dimensional model. Three-dimensional simulations do predict the performance with reasonable precision. Gain in excess of 100% per pass and an efficiency close to 1/2NW, where NW is the number of wiggler periods, is seen. The laser mirror tuning curves currently permit operation in the wavelength range of 438 to 362 nm. Another mirror set allows operation at longer wavelengths in the red with even higher gain and efficiency.

43 PARTICLE ACCELERATORS↗

Design of the SRF Driver ERL for the Jefferson Lab UV FEL

We describe the design of the SRF Energy-Recovering Linac (ERL) providing the CW electron drive beam at the Jefferson Lab UV FEL. Based on the same 135 MeV linear accelerator as and sharing portions of the recirculator with the Jefferson Lab 10 kW IR Upgrade FEL, the UV driver ERL uses a novel bypass geometry to provide transverse phase space control, bunch length compression, and nonlinear aberration compensation (including correction of RF curvature effects) without the use of magnetic chicanes or harmonic RF. Stringent phase space requirements at the wiggler, low beam energy, high beam current, and use of a pre-existing facility and legacy hardware subject the design to numerous constraints. These are imposed not only by the need for both transverse and longitudinal phase space management, but also by the potential impact of collective phenomena (space charge, wakefields, beam break-up (BBU), and coherent synchrotron radiation (CSR)), and by interactions between the FEL and the accelerator RF system. This report addresses these issues and presents the accelerator design solution that is now in operation.

43 PARTICLE ACCELERATORS↗

Electron Beam Diagnostics Of The JLAB UV FEL

In this contribution we describe various systems and aspects of the electron beam diagnostics of the JLab UV FEL. The FEL is installed on a new bypass beam line at the existing 10 kW IR Upgrade FEL. Here, we describe a set of the following systems. A combination of OTR and phosphor viewers is used for measurements of the transverse beam profile, transverse emittance, and Twiss parameters. This system is also used for alignment of the optical cavity of the UV oscillator and to ensure the overlap between the electron beam and optical mode in the FEL wiggler. A system of beam position monitors equipped with log-amp based BPM electronics. Bunch length on the order of 120 fs RMS is measured with the help of a modified Martin-Puplett interferometer. The longitudinal transfer function measurement system is used to set up bunch compression in an optimal way, such that the LINAC RF curvature is compensated using only higher order magnetic elements of the beam transport. This set of diagnostic systems made a significant contribution in achieving first lasing of the FEL after only about 60 hours of beam operation.

43 PARTICLE ACCELERATORS↗

Use of Multipass Recirculation and Energy Recovery In CW SRF X-FEL Driver Accelerators

We discuss the use of multipass recirculation and energy recovery in CW SRF drivers for short wavelength FELs. Benefits include cost management (through reduced system footprint, required RF and SRF hardware, and associated infrastructure - including high power beam dumps and cryogenic systems), ease in radiation control (low drive beam exhaust energy), ability to accelerate and deliver multiple beams of differing energy to multiple FELs, and opportunity for seamless integration of multistage bunch length compression into the longitudinal matching scenario. Issues include all those associated with ERLs compounded by the challenge of generating and preserving the CW electron drive beam brightness required by short wavelength FELs. We thus consider the impact of space charge, BBU and other environmental wakes and impedances, ISR and CSR, potential for microbunching, intra-beam and beam-residual gas scattering, ion effects, RF transients, and halo, as well as the effect of traditional design, fabrication, installation and operational errors (lattice aberrations, alignment, powering, field quality). Context for the discussion is provided by JLAMP, the proposed VUV/X-ray upgrade to the existing Jefferson Lab FEL.

43 PARTICLE ACCELERATORS↗

Distributed Wireless Multi-Sensor Technologies, A Novel Approach to Reduce Motor Energy Usage

This report is the final report for the General Electric Distributed Wireless Multi-Sensor Technologies project. The report covers the research activities and benefits surrounding wireless technology used for industrial sensing applications. The main goal of this project was to develop wireless sensor technology that would be commercialized and adopted by industry for a various set of applications. Many of these applications will yield significant energy savings. One application where there was significant information to estimate a potential energy savings was focused on equipment condition monitoring and in particular electric motor monitoring. The results of the testing of the technology developed are described in this report along with the commercialization activities and various new applications and benefits realized.

42 ENGINEERING↗

ETHERNET BASED EMBEDDED IOC FOR FEL CONTROL SYSTEM

An Ethernet based embedded Input Output Controller (IOC) has been developed to upgrade the control system for the Free Electron Laser Project at Jefferson Lab. The embedded IOC, called the Single Board IOC (SBIOC), was integrated with a ColdFire embedded microprocessor and a Field Programmable Gate Array (FPGA) on a circuit board, which can be easily configured to control different kinds of I/O devices. The SBIOC provided features of a complete System-on-Module (SOM) as a stand alone system with abundant high speed I/O ports to couple with suitable devices. The software kits, Experimental Physics and Industrial Control System (EPICS) and Real Time Executive for Multiprocessor System (RTEMS), were chosen to work with our existing control system. The embedded IOC system has the features of a low cost IOC, free open source RTOS, plug-and-play-like ease of installation and flexibility.

43 PARTICLE ACCELERATORS↗

Ethernet Based Embedded IOC for FEL Control Systems

An Ethernet based embedded Input Output Controller (IOC) has been developed as part of an upgrade to the control system for the Free Electron Laser Project at Jefferson Lab. Currently most of the FEL systems are controlled, configured and monitored using a central VME bus-based configuration. These crate based systems are limited in growth and usually interleave multiple systems. In order to accommodate incremental system growth and lower channel costs, we developed a stand-alone system, an Ethernet based embedded controller called the Single Board IOC (SBIOC). The SBIOC is a module which integrates an Altera FPGA and the Arcturus uCdimm Coldfire 5282 Microcontroller daughter card into one module, which can be easily configured for different kinds of I/O devices. The microcontroller is a complete System-on-Module, including three highly integrated functional blocks, the core processor, memory, and Ethernet communication. A real-time operating system, RTEMS is cross compiled with

97 MATHEMATICS AND COMPUTING↗