CuCl Treatment Variations in High Efficiency Polycrystalline CdSe x Te 1-x /CdTe Thin Film Solar Cells
Not provided.
Energy & Fuels↗
Engineering topics
Shah, Akash
Publications and source records attributed to Shah, Akash.
Te/CdTe and Al/CdTe Interfacial Energy Band Alignment by Atomistic Modeling
A synergistic approach that incorporates first-principles atomistic modeling with numerical device simulations is used to systematically evaluate the role of heterointerfaces within metal-chalcogenide-based photovoltaic technologies. Two interfaces involving either a tellurium back contact or aluminum back electrode combined with a cadmium telluride absorber layer within cadmium-telluride-based thin-film solar cells are investigated on an atomic scale to determine the mechanisms contributing to variations in device performance. Electronic structures and predicted charge transport behavior with respect to cadmium and tellurium termination of the absorber layer are studied along the polar oriented CdTe{111} facets. The computational methodology reveals a noticeable contrast between the Schottky barrier forming Al/CdTe interface versus the Type I Te/CdTe heterojunction. Greater band bending features are exhibited by the cadmium termination as opposed to the tellurium termination for each interface case. Subsequent device modeling suggests that 3.6% higher photovoltaic conversion efficiency is achievable for the cadmium termination relative to the tellurium termination of the Te/CdTe interface. Based strictly on an idealistic representation, both interface models show the importance of atomic-scale interfacial properties for cadmium telluride solar cell device performance with their bulk properties being validated in comparison to published experimental data. Here, the synergistic approach offers a suitable method to analyze solar cell interfaces through a predictive computational framework for the engineering and optimization of metal-chalcogenide-based thin-film photovoltaic technologies.
Green’s function↗
Beryllium Probe Neutron Diagnostic for a Gas-Puff Z-Pinch Neutron Source on a 1-MA, 100-ns Linear Transformer Driver.
Abstract not provided.
White, Donovan↗
Understanding the Role of CdTe in Polycrystalline CdSe x Te 1– x /CdTe-Graded Bilayer Photovoltaic Devices
Grading of bandgap by alloying CdTe with selenium to form a CdSe x Te 1–x /CdTe-graded bilayer device has led to a device efficiency over 19%. A CdSe x Te 1–x absorber would increase the short-circuit current due to its lower bandgap but at the expense of open-circuit voltage. It has been demonstrated that adding a CdTe layer at the back of such a CdSe x Te 1–x film reduces the voltage deficit caused by the lower bandgap of absorber from selenium alloying while maintaining the higher short-circuit current. This leads to a photovoltaic device that draws advantage from both materials with an efficiency greater than either of them. In this report there is a detailed account using device data, ultraviolet photoelectron spectroscopy, electron microscopy, and first-principles density functional theory modeling is provided, which shows that CdTe acts as an electron reflector for CdSe x Te 1–x .
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Mitigation of J–V distortion in CdTe solar cells by Ga-doping of MgZnO emitter
Distortions in the current–voltage curves of CdTe-based thin-film solar cells with MgZnO emitter layers are not uncommon. Even when such distortions are very subtle with standard sunlight, they can be greatly accentuated by the removal of short-wavelength photons with optical filters, and the dark-curve turn-on voltage can be noticeably increased. The strong suggestion is that good J–V curves with full-spectrum light often rely on photogeneration of electrons from trap states in the MgZnO emitter. When the carrier concentration of the CdTe absorber is increased with external doping, there is a corresponding need for a larger MgZnO carrier concentration. Based on the assumption that the emitter carrier concentration needs to be comparable to that of the absorber, Ga-doping of the MgZnO was shown to very nearly eliminate the large filtered-light distortions and is arguably superior to MgZnO that relies on photogeneration. In addition, it was shown that photogeneration and recovery in MgZnO is relatively slow, so that without Ga-doping, the cell efficiency improves gradually for most of an hour in the light, and the turn-on voltage of the dark curve increases on a similar time scale when the light is removed.
36 MATERIALS SCIENCE↗
Transparent MgO for Back-Contact Passivation of CdTe-Based Solar Cells
The passivating effects of MgO have been studied by integrating into an existing superstrate CdTe thin film solar cell device architecture. When implemented as an emitter to replace the typical MZO, the device performance was below par, but improved PL and TRPL was detected with significant carrier lifetimes in comparison to the MZO devices. However, when integrated at the back, the PL signal was detected upon the illumination of excitation laser from the back. This has opened the possibility of probing the back of the CdTe thin film solar cells with transparent back contact with improved back passivation and a bifacial device structure. Further, the TRPL measurements suggests that the MgO shows passivating effects to a CdTe surface irrespective of method of deposition implemented.
bifacial↗
Understanding the Copassivation Effect of Cl and Se for CdTe Grain Boundaries
Not provided.
Materials Science↗
CdTe‐Based Solar Cells with Variations in Mg Concentration in the MgZnO Emitter
The optimal fraction of Mg incorporation in sputter-deposited Mg X Zn 1−X O (MZO) emitters for thin-film CdTe-based solar cells is evaluated by varying it over a range of x from 0 to 0.35. This range allows a variation in the conduction band offset from −0.1 eV (cliff like) to +0.32 eV (spike like). Here, a maximum efficiency of 18.5% for cells with the bilayer CdSeTe/CdTe absorber occurs at x = 0.15, which corresponds to a spike-like band offset near 0.2 eV, as confirmed by X-ray photoelectron spectroscopy. In addition, good cell performance is seen over a fairly broad range of x extending from 0.1 to 0.25. The MZO optical bandgap increases with the Mg fraction, consistent with an increasing conduction band offset. Temperature-dependent current−voltage measurements and time-resolved photoluminescence show improvement in the emitter/absorber interface with the incorporation of Mg. Capacitance−voltage measurements show that the depletion region extends further into the absorber with more Mg, and X-ray diffraction confirms a change from a hexagonal-dominant crystal structure toward zinc blende at x = 0.35.
14 SOLAR ENERGY↗
Atomistic modeling of energy band alignment in CdSeTe surfaces
Atomistic modeling based on Desnity Functional Theory (DFT)- 1/2 method coupled with surface Green’s function has been employed to investigate the energy band alignment results in cadmium selenium telluride (CdSeTe) surfaces. The structural and electronic properties of the bulk ternary alloy were established before cleaving the CdSeTe low index surface facets. The dependency of atomic-scale electronic features on different plane orientations was explored by studying the energy band alignment diagrams in the unreconstructed and reconstructed surfaces. While the low index CdSeTe surface geometry reconstructions replicate the CdTe surface geometries, the energy band alignment features of the unreconstructed and reconstructed CdSeTe surfaces differ from those observed in CdTe low index surfaces. The structurally relaxed reconstructed CdSeTe surface results in purely flat bands as opposed to an internal cusp feature observed in CdTe surfaces. The presence of an internal energy cusp in CdTe(111) surfaces is expected to play a key role in enhancing the hole charge transport towards the back of CdTe-only solar cell device and the absence of such feature in CdSeTe surface may explain one of the reason for the lower performance of CdSeTe-only solar cell seen experimentally.
36 MATERIALS SCIENCE↗
A Density Functional Theory (DFT) Study on the Effect of Chlorine in the Magnesium Zinc Oxide (MZO) Front Interface for Cadmium Telluride (CdTe) Thin Film Solar Cells
Cadmium telluride photovoltaics has benefitted greatly from the cadmium chloride treatment which causes a remarkable improvement in cell efficiencies. This work investigates the effect of elemental chlorine at the interface between the magnesium zinc oxide front contact and the cadmium telluride absorber in such a device. Band alignment including band bending and interface states and its role in potential charge carrier transport is the key feature studied. It is seen that a small amount of chlorine is leads to a more desirable band alignment. Higher concentrations of chlorine result in unfavorable band characteristics.
14 SOLAR ENERGY↗
Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations
We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5x1015 cc-1 and external radiative efficiency of over 2% in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.
14 SOLAR ENERGY↗
Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations
We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5×l0 15 cc -1 and external radiative efficiency of over 2 % in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.
Munshi, Amit H.↗
Atomistic modeling of energy band alignment in CdTe(1 0 0) and CdTe(1 1 1) surfaces
An atomic-scale perspective of energy band alignment in CdTe surfaces has not been spatially studied despite the major role surfaces play in forming interfaces within CdTe-based thin film photovoltaic devices. Atomistic modeling based on density functional theory coupled with surface Green’s function is used for calculating energy band alignment of CdTe surfaces. The CdTe(1 0 0) ((1×1) and c(2×2) reconstruction) and CdTe(1 1 1) ((1×1) and (2×2) reconstruction) facets without and with surface relaxation provide insightful band bending characteristics that influence charge carrier transport. Results show that unrelaxed (1×1) CdTe(1 0 0) and CdTe(1 1 1) surfaces bend the valence band downward with surface polarity dictating the surface potential magnitude. The reconstructed CdTe(1 0 0) c(2×2) and CdTe(1 1 1) (2×2) surfaces result in favorable surface electronic features in relation to their unreconstructed variants. In addition, the structurally relaxed CdTe(1 1 1) surfaces develop an internal energy cusp potential that may enhance hole charge transport toward the back of CdTe solar cell devices. In conclusion, energy band alignments calculated within the study lead to a detailed understanding of how CdTe surfaces may affect CdTe-based thin film photovoltaic applications.
36 MATERIALS SCIENCE↗