Engineering topics

Shah, Gautam H.

Publications and source records attributed to Shah, Gautam H..

At least 19 records

NASA NTRS2019

Computational Study of a Generic T-tail Transport

This paper presents a computational study on the static and dynamic stability characteristics of a generic transport T-tail configuration under a NASA research program to improve stall models for civil transports. The NASA Tetrahedral Unstructured Software System (TetrUSS) was used to obtain both static and periodic dynamic solutions at low speed conditions for three Reynolds number conditions up to 60 deg angle of attack. The computational results are compared to experimental data. The dominant effects of Reynolds number for the static conditions were found to occur in the stall region. The pitch and roll damping coefficients compared well to experimental results up to up to 40 deg angle of attack whereas yaw damping coefficient agreed only up to 20 deg angle of attack.

McMillin, S. Naomi↗

NASA NTRS2019

Verification of a Motion Cueing Strategy for Stall Recovery Training in a Commercial Transport Simulator

This presentation verifies a motion cueing strategy for improved pilot stall recovery training in commercial transport simulators. Eight airline transport pilots flew a high-altitude stall recovery task in the NASA B747 level-D-certified full flight simulator under three different motion configurations: no motion, baseline motion, and enhanced motion. For each motion condition, pilots performed the task with both baseline aircraft dynamics and aircraft dynamics enhanced with lateral-directional characteristics of the airplane at angle of attack approaching stall. Motion configuration significantly affected: 1) pilot opinions on the helpfulness of motion in performing the task, 2) the maximum roll angle in the stall maneuver, 3) the minimum load factor in the recovery, 4) the number of secondary stick shakers in the stall recovery, and 5) the maximum airspeed in the recovery. The two different aircraft dynamics significantly affected: 1) pilot opinions on the noticeability of the banking roll off near the stall and 2) the maximum roll angle in the stall maneuver. These results indicate that the relatively minor enhancements to the motion logic of heritage commercial transport simulators presented here can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

Zaal, Petrus M. T.↗

NASA NTRS2019

Verification of a Motion Cueing Strategy for Stall Recovery Training in a Commercial Transport Simulator

This paper verifies a motion cueing strategy for improved pilot stall recovery training in commercial transport simulators. Eight airline transport pilots flew a high-altitude stall recovery task in the NASA B747 level-D-certified full flight simulator under three different motion configurations: no motion, baseline motion, and enhanced motion. For each motion condition, pilots performed the task with both baseline aircraft dynamics and aircraft dynamics enhanced with lateral-directional characteristics of the airplane at angle of attack approaching stall. Motion configuration significantly affected: 1) pilot opinions on the helpfulness of motion in performing the task, 2) the maximum roll angle in the stall maneuver, 3) the minimum load factor in the recovery, 4) the number of secondary stick shakers in the stall recovery, and 5) the maximum airspeed in the recovery. The two different aircraft dynamics significantly affected: 1) pilot opinions on the noticeability of the banking roll off near the stall and 2) the maximum roll angle in the stall maneuver. These results indicate that the relatively minor enhancements to the motion logic of heritage commercial transport simulators presented here can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

Pilot Performance↗

NASA NTRS2019

Unsteady Model Estimation for Generic T-Tail Transport Aircraft Using Computational Data

Models including nonlinear and unsteady behaviors are developed for the longitudinal axis of the NASA Generic T-Tail Aircraft over a large range of angle of attack. These models are based on computational simulations of forced-oscillation tests in a wind tunnel. This work continues a recent study and an ongoing effort by NASA to improve aircraft simulations for pilot training in loss-of-control and stalled conditions. The objective of this work is to develop appropriate aerodynamic models that provide representative responses in simulation for a given class of aircraft. In the stall region, nonlinear unsteady responses are often present and may require an extended aerodynamic model compared to that used in the conventional flight envelope. In this study, two objectives are addressed. The first is to obtain representative models for the NASA Generic T-Tail aircraft over a wide range of angle of attack and the second is to continue development of a specialized CFD test technique that uses Schroeder sweeps to create information rich responses for unsteady aerodynamic model identification.

Murphy, Patrick C.↗

NASA NTRS2019

Investigation of Reduced-Order Modeling for Aircraft Stability and Control Prediction

High-fidelity computational fluid dynamics tools offer the potential to approximate increments for ground-to-flight scaling effects, as well as to augment the dynamic damping derivative data for motion-based flight simulators. Unfortunately, the computational expense is currently prohibitive for populating a complete simulator database. This work investigates an existing surrogate-based, indicial response reduced-order model methodology as a means to efficiently augment a flight simulator database with high-fidelity nonlinear aerodynamic damping derivatives. Creation of the reduced-order model is based on the superposition integrals of the step response with the derivative of its corresponding input signal. Step responses are calculated using a computational grid motion approach that separates the effects of angle of attack and sideslip angle from angular rates, and rates from angle of attack and sideslip. It is demonstrated that the transients produced during the start of a forced-oscillation motion are captured by the reduced-order model to the level of fidelity of a comparable computational solution. Aerodynamic coefficients computed within minutes by the reduced-order model for an aircraft undergoing an 18-second half Lazy-8 maneuver and a 25-second Immelmann turn maneuver are compared with those from full computational flight solutions that required days to complete. Finally, a cost-benefit assessment is included that demonstrates a compelling advantage for this approach. d for maneuvering, flexible vehicles.

Frink, Neal T.↗

NASA NTRS2019

Pilot Sensitivity to Simulator Flight Dynamics Model Formulation for Stall Training

A piloted simulation study was performed in the Cockpit Motion Facility at the National Aeronautics and Space Administration Langley Research Center. The research was motivated by the desire to reduce the commercial transport airplane fatal accident rate due to in-flight loss of control. The purpose of this study, which focused on a generic T-tail transport airplane, was to assess pilot sensitivity to flight dynamics model formulation used during a simulator stall recognition and recovery training/demonstration profile. To accomplish this, the flight dynamics model was designed with many configuration options. The model options were based on recently acquired static and dynamic stability and control data from sources that included wind tunnel, water tunnel, and computational fluid dynamics. The results, which are specific to a transport airplane stall recognition and recovery guided demonstration scenario, showed the two most important aerodynamic effects (other than stick pusher) to model were stall roll- off and the longitudinal static stability characteristic associated with the pitch break.

Cunningham, Kevin↗

NASA NTRS2018

Efficient Unsteady Model Estimation Using Computational and Experimental Data

Improving aircraft simulations for pilot training in loss-of-control and stalled conditions is one goal of NASA research in the System Wide Safety Program. One part of this effort is to develop appropriate generic aerodynamic models that provide representative responses in simulation for a given class of aircraft. In this part of the flight envelope nonlinear unsteady responses are often present and may require an extended aerodynamic model compared to that used in the conventional flight envelope. In this preliminary study, two objectives are addressed. First, to obtain a representative model for a NASA generic aircraft at an unsteady condition in the flight envelope and second, to evaluate the techniques involved. To meet these objectives, two different generic aircraft configurations are modeled using both experimental and analytical data. With these results, an initial assessment of the efficiency and quality of the tools and test techniques are evaluated to develop guidance for analytical and experimental approaches to unsteady modeling.

Murphy, Patrick C.↗

NASA NTRS2018

Preliminary Test Results for Stability and Control Characteristics of a Generic T-Tail Transport Airplane at High Angle of Attack

Tests of a generic T-tail transport airplane, in flaps-up configuration, were conducted using two wind tunnels, a water tunnel, and computational fluid dynamics. Static force and moment testing, forced oscillation testing and dye flow visualization test techniques were used. The purpose of the testing was to obtain stability and control characteristics for development of a research flight simulator aerodynamic database. The purpose of that database was for assessment of aerodynamic model fidelity requirements to train airline pilots to recognize and recover from full stall conditions. Preliminary results, at initial stall conditions, include: an unstable stall pitch break, and near-neutral roll damping. Preliminary results, at deep stall conditions, include: a potential static longitudinal trim condition at approximately 35 degrees angle of attack, large aerodynamic asymmetries, and localized unstable dynamic stability.

Cunningham, Kevin↗

NASA NTRS2018

A Generic T-Tail Transport Airplane Simulation for High-Angle-Of-Attack Dynamics Modeling Investigations

A preliminary simulation of a generic T-tail transport airplane configuration has been developed at the National Aeronautics and Space Administration Langley Research Center. The primary purpose of this piloted simulation is to assess aerodynamic model fidelity requirements for training airline pilots to recognize and recover from full-stall flight conditions in a T-tail airplane. As a result, significant flexibility has been designed into the flight dynamics model. The flight dynamics model is based on newly acquired static and dynamic stability and control data from sources that include: wind tunnel, water tunnel, and computational fluid dynamics. Preliminary results for initial stall show an unstable stall pitch break (if the stick pusher is inhibited), un-commanded motions due to stall asymmetries, significantly reduced dynamic roll stability, and decreased control effectiveness. Preliminary studies indicated an insensitivity to the fidelity of the pitch damping model.

Cunningham, Kevin↗

NASA NTRS2012

Flight Dynamics Modeling and Simulation of a Damaged Transport Aircraft

A study was undertaken at NASA Langley Research Center to establish, demonstrate, and apply methodology for modeling and implementing the aerodynamic effects of MANPADS damage to a transport aircraft into real-time flight simulation, and to demonstrate a preliminary capability of using such a simulation to conduct an assessment of aircraft survivability. Key findings from this study include: superpositioning of incremental aerodynamic characteristics to the baseline simulation aerodynamic model proved to be a simple and effective way of modeling damage effects; the primary effect of wing damage rolling moment asymmetry may limit minimum airspeed for adequate controllability, but this can be mitigated by the use of sideslip; combined effects of aerodynamics, control degradation, and thrust loss can result in significantly degraded controllability for a safe landing; and high landing speeds may be required to maintain adequate control if large excursions from the nominal approach path are allowed, but high-gain pilot control during landing can mitigate this risk.

Shah, Gautam H.↗

NASA NTRS2012

Aerodynamic Effects of Simulated Ice Accretion on a Generic Transport Model

An experimental research effort was begun to develop a database of airplane aerodynamic characteristics with simulated ice accretion over a large range of incidence and sideslip angles. Wind-tunnel testing was performed at the NASA Langley 12-ft Low-Speed Wind Tunnel using a 3.5 percent scale model of the NASA Langley Generic Transport Model. Aerodynamic data were acquired from a six-component force and moment balance in static-model sweeps from alpha = -5deg to 85deg and beta = -45 deg to 45 deg at a Reynolds number of 0.24 x10(exp 6) and Mach number of 0.06. The 3.5 percent scale GTM was tested in both the clean configuration and with full-span artificial ice shapes attached to the leading edges of the wing, horizontal and vertical tail. Aerodynamic results for the clean airplane configuration compared favorably with similar experiments carried out on a 5.5 percent scale GTM. The addition of the large, glaze-horn type ice shapes did result in an increase in airplane drag coefficient but had little effect on the lift and pitching moment. The lateral-directional characteristics showed mixed results with a small effect of the ice shapes observed in some cases. The flow visualization images revealed the presence and evolution of a spanwise-running vortex on the wing that was the dominant feature of the flowfield for both clean and iced configurations. The lack of ice-induced performance and flowfield effects observed in this effort was likely due to Reynolds number effects for the clean configuration. Estimates of full-scale baseline performance were included in this analysis to illustrate the potential icing effects.

Broeren, Andy P.↗

NASA NTRS2010

Simulation Modeling for Off-Nominal Conditions - Where Are We Today?

The modeling of aircraft flight characteris4cs in off-nominal or otherwise adverse conditions has become increasingly important for simulation in the loss-of-control arena. Adverse conditions include environmentally-induced upsets such as wind shear or wake vortex encounters; off-nominal flight conditions, such as stall or departure; on-board systems failures; and structural failures or aircraft damage. Spirited discussions in the research community are taking place as to the fidelity and data requirements for adequate representation of vehicle dynamics under such conditions for a host of research areas, including recovery training, flight controls development, trajectory guidance/planning, and envelope limiting. The increasing need for multiple sources of data (empirical, computational, experimental) for modeling across a larger flight envelope leads to challenges in developing methods of appropriately applying or combining such data, particularly in a dynamic flight environment with a physically and/or aerodynamically asymmetric vehicle. Traditional simplifications and symmetry assumptions in current modeling methodology may no longer be valid. Furthermore, once modeled, challenges abound in the validation of flight dynamics characteristics in adverse flight regimes

Shah, Gautam H.↗

NASA NTRS2008

Aerodynamic Effects and Modeling of Damage to Transport Aircraft

A wind tunnel investigation was conducted to measure the aerodynamic effects of damage to lifting and stability/control surfaces of a commercial transport aircraft configuration. The modeling of such effects is necessary for the development of flight control systems to recover aircraft from adverse, damage-related loss-of-control events, as well as for the estimation of aerodynamic characteristics from flight data under such conditions. Damage in the form of partial or total loss of area was applied to the wing, horizontal tail, and vertical tail. Aerodynamic stability and control implications of damage to each surface are presented, to aid in the identification of potential boundaries in recoverable stability or control degradation. The aerodynamic modeling issues raised by the wind tunnel results are discussed, particularly the additional modeling requirements necessitated by asymmetries due to damage, and the potential benefits of such expanded modeling.

Shah, Gautam H.↗

NASA NTRS2005

Dynamics Modeling and Simulation of Large Transport Airplanes in Upset Conditions

As part of NASA's Aviation Safety and Security Program, research has been in progress to develop aerodynamic modeling methods for simulations that accurately predict the flight dynamics characteristics of large transport airplanes in upset conditions. The motivation for this research stems from the recognition that simulation is a vital tool for addressing loss-of-control accidents, including applications to pilot training, accident reconstruction, and advanced control system analysis. The ultimate goal of this effort is to contribute to the reduction of the fatal accident rate due to loss-of-control. Research activities have involved accident analyses, wind tunnel testing, and piloted simulation. Results have shown that significant improvements in simulation fidelity for upset conditions, compared to current training simulations, can be achieved using state-of-the-art wind tunnel testing and aerodynamic modeling methods. This paper provides a summary of research completed to date and includes discussion on key technical results, lessons learned, and future research needs.

Foster, John V.↗

NASA NTRS2005

Simulation Study of Flap Effects on a Commercial Transport Airplane in Upset Conditions

As part of NASA's Aviation Safety and Security Program, a simulation study of a twinjet transport airplane crew training simulation was conducted to address fidelity for upset or loss of control conditions and to study the effect of flap configuration in those regimes. Piloted and desktop simulations were used to compare the baseline crew training simulation model with an enhanced aerodynamic model that was developed for high-angle-of-attack conditions. These studies were conducted with various flap configurations and addressed the approach-to-stall, stall, and post-stall flight regimes. The enhanced simulation model showed that flap configuration had a significant effect on the character of departures that occurred during post-stall flight. Preliminary comparisons with flight test data indicate that the enhanced model is a significant improvement over the baseline. Some of the unrepresentative characteristics that are predicted by the baseline crew training simulation for flight in the post-stall regime have been identified. This paper presents preliminary results of this simulation study and discusses key issues regarding predicted flight dynamics characteristics during extreme upset and loss-of-control flight conditions with different flap configurations.

Cunningham, Kevin↗

NASA NTRS2004

Comparison of Rolling Moment Characteristics During Roll Oscillations for a Low and a High Aspect Ratio Configuration

Improvements in testing and modeling of nonlinear and unsteady aerodynamic effects for flight dynamics predictions of vehicle performance is critical to enable the design and implementation of new, innovative vehicle concepts. Any configuration which exhibits significant flow separation, nonlinear aerodynamics, control interactions or attempts maneuvering through one or more conditions such as these is, at present, a challenge to test, model or predict flight dynamic responses prior to flight. Even in flight test experiments, adequate models are not available to study and characterize the complex nonlinear and time-dependent flow effects occurring during portions of the maneuvering envelope. Traditionally, airplane designs have been conducted to avoid these areas of the flight envelope. Better understanding and characterization of these flight regimes may not only reduce risk and cost of flight test development programs, but also may pave the way for exploitation of those characteristics that increase airplane capabilities. One of the hurdles is that the nonlinear/unsteady effects appear to be configuration dependent. This paper compares some of the dynamic aerodynamic stability characteristics of two very different configurations - representative of a fighter and a transport airplane - during dynamic body-axis roll wind tunnel tests. The fighter model shows significant effects of oscillation frequency which are not as apparent for the transport configuration.

Brandon, Jay M.↗

NASA NTRS1999

Correlation of Fin Buffet Pressures on an F/A-18 with Scaled Wind-Tunnel Measurements

Buffeting is an aeroelastic phenomenon occurring at high angles of attack that plagues high performance aircraft, especially those with twin vertical tails. Previous wind-tunnel and flight tests were conducted to characterize the buffet loads on the vertical tails by measuring surface pressures, bending moments, and accelerations. Following these tests, buffeting responses were computed using the measured buffet pressures and compared to the measured buffeting responses. The calculated results did not match the measured data because the assumed spatial correlation of the buffet pressures was not correct. A better understanding of the partial (spatial) correlation of the differential buffet pressures on the tail was necessary to improve the buffeting predictions. Several wind-tunnel investigations were conducted for this purpose. When compared, the results of these tests show that the partial correlation scales with flight conditions. One of the remaining questions is whether the wind-tunnel data is consistent with flight data. Presented herein, cross-spectra and coherence functions calculated from pressures that were measured on the High Alpha Research Vehicle indicate that the partial correlation of the buffet pressures in flight agrees with the partial correlation observed in the wind tunnel.

Moses, Robert W.↗

NASA NTRS1999

Application of Forebody Strakes for Directional Stability and Control of Transport Aircraft

A brief overview of a cooperative NASA/Boeing research effort, Strake Technology Research Application to Transport Aircraft (STRATA), intended to explore the potential of applying forebody strake technology to transport aircraft configurations for directional stability and control at low angles of attack, is presented. As an initial step in the STRATA program, an exploratory wind-tunnel investigation of the effect of fixed forebody strakes on the directional stability and control characteristics of a generic transport configuration was conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. Results of parametric variations in strake chord and span, as well as the effect of strake incidence, are presented. The use of strakes for yaw control is also discussed. Results emphasize the importance of forebody/fuselage crossflow in influencing strake effectiveness. Strake effectiveness is also seen to be directly related to its span, but less sensitive to chord; a very short-chord strake with sufficient span can have a significant effect.

Shah, Gautam H.↗