Engineering topics

Shahwan, Khaled W.

Publications and source records attributed to Shahwan, Khaled W..

6 records

DOE OSTI2026

A mild calcium carbonate treatment improves moisture resistance and mechanical/interfacial properties of jute and hemp fibers

Natural fibers are attractive, sustainable reinforcements, but often exhibit high moisture uptake and weak bonding with polymer matrices. In this study, jute and hemp were treated by immersion in aqueous calcium carbonate (CaCO3) suspensions (10–40?wt.%, 1.5?h, room temperature) and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), moisture sorption testing, single-fiber tensile testing, and bundle pull-out testing. SEM showed granular CaCO3 deposition on fiber surfaces, with particulates bridging surface voids and microcracks. At 40 wt.% CaCO3, equilibrium moisture uptake decreased to ~5% (hemp) and ~3% (jute), while tensile strength increased to ~904 MPa (hemp) and ~960 MPa (jute). Apparent interfacial shear strength from pull-out testing increased up to ~1.35 MPa (hemp) and ~0.56 MPa (jute). These results indicate that CaCO3 deposition is a mild, scalable surface treatment that improves moisture resistance, fiber tensile strength, and interfacial load transfer relevant to semi-structural composite applications, including interior and secondary automotive components.

Calcium carbonate treatment↗

DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Equivalent Properties of Interfacial Void Defects at the CFRTP-adhesive Interface and Their Detrimental Effects on the Bonding Performance of Metal-CFRTP Dissimilar Joints

This paper revealed the detrimental effects of micro-scale air interfacial voids on the debonding at the interface of carbon-fiber-reinforced polyphthalamide (CFRPPA) and thermoset adhesive, representing a weak adherend-adhesive interface, within a dissimilar joint made of an aluminum alloy and a CFRPPA. The reduced lap shear strength of the joint, due to different void area fractions at the CFRPPA-adhesive interface, can be computationally described by using equivalent interfacial properties in the modeling to avoid the explicit modeling of the micro-scale interfacial voids. Such equivalent interfacial properties (e.g., interfacial normal strength, etc.) was found to have a non-linear relationship with respect to interfacial void area fraction as well as lap shear strength. This work has practical applications by utilizing equivalent interfacial properties for the analytical and/or computational design(s) of adhesively bonded joints.

Qiao, Yao↗

DOE OSTI2024

Wholly Sustainable, Cost-Effective Carbon Fiber-Nylon Compounds CRADA 592 (Final Report)

Carbon fiber composites have attracted considerable attention due to the potential for substantial mass savings, with many examples now implemented in the low-volume luxury car market. However, migration to higher volume applications has been hindered by: (a) high material cost, (b) high processing times, and (c) perception of low Sustainability. This project will address all three of these barriers: (a) carbon fiber material to replace aluminum in structural components at a cost penalty of no more than $5/Kg-saved (aka weight buy), (b) fitting into high-rate processes for automotive production like injection molding, and (c) end-to-end Sustainable material – based on post industrial waste carbon fiber and nylon 66 and ability to recycle end-of-life auto parts. The opportunity lies in combining DowAksa capabilities in carbon fiber manufacturing, resin chemistry intermediate production with the unique testing capabilities inherent within PNNL. The teams from PNNL and DowAksa held several meetings virtually and in-person in Michigan and at PNNL, including a lab tour at PNNL. Throughout, the teams discussed DowAksa material sources, commercially available recycled base materials, and preliminary material properties. The teams also engaged in multiple discussions and evaluations of potential automotive applications based on the ideas suggested by PNNL. The teams discussed several potential automotive applications in which recycled carbon fiber and recycled PA resin can be used. The PNNL team identified 38 cast aluminum components that can potentially be assessed for redesign using the DowAksa materials system. The PNNL team also identified 27 polyamide components. The teams discussed the lists and narrowed it down to a handful of applications that are exterior and interior to common vehicle architectures. The team also considered semi-structural and structural components and short-listed the highest potential candidates, such as cross-car-beam. The cross-car beam was considered to be highly suitable and potentially viable demonstration applications based on the properties of the materials as well as the weight savings potentials and the reduction in embodied energy by utilizing wholly sustainable materials, since both materials, carbon fiber and resin, were derived from recycled materials. The next step was to reach out to potential OEMs and/or Tier1s who were interested in exploring such technology for future applications. However, the project was terminated, and no further discussions or exchange of information took place. No new data were generated, including no IP and no publications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Low-velocity repeated impact behaviors of Polymer Fiber Reinforced Plastics (PFRPs)

Modern fiber-reinforced composites have become ubiquitous across multiple industries due to their excellent weight-to-strength ratio. Typically glass or carbon fibers are widely used. While Glass or Carbon Fiber-Reinforced Plastics (GFPRs or CFPRs) have good stiffness, strength, and fatigue life, they are expensive and difficult to recycle. Researchers are exploring Polymer Fiber-Reinforced Plastics (PFRPs) as an alternative solution. PFRPs utilize polymer fibers and a polymer matrix. A wide range of materials options is available, including low-cost thermoplastics such as polyethylene or polypropylene. These thermoplastics are easy to handle and recyclable without special methods. Manufacturing parts using thermoplastics are well-established as well. However, their mechanical performances have not been extensively studied compared to GFRPs or CFRPs. This study examines the low-velocity impact resistance of PFRPs made of different thermoplastics. The low-velocity impacts are applied through a drop-weight tower. The experiment is divided into two cases: a single perforation impact and low-energy repeated impacts. Energy absorption and the number of impacts to failure are measured. The results are compared to traditional CFRPs which have a thermoset matrix. The PFRPs demonstrate energy absorption capabilities comparable to or greater than those of CFRPs with respect to specimen thickness and density. Additionally, the PFRPs show significantly higher impacts-to-failure than the CFRPs in low-energy repeated impact tests. This is particularly noteworthy considering that the PFRPs are much simpler and more economical to manufacture than CFRPs. To further

Ko, Seunghyun↗

DOE OSTI2023

Processing Temperature Effect on Failure Behavior of Unidirectional Thermoplastic Polymer-fiber-reinforced Polymers (PFRPs)

This study aimed to examine the influence of processing temperature on the mechanical and morphological characteristics of unidirectional (UD) thermoplastic polymer-fiber-reinforced polymers (PFRPs), utilizing UHMWPE-polymer-fiber-reinforced HDPE composites as an example. To achieve this objective, UD thermoplastic PFRPs were produced through filament winding and hot pressing techniques, employing five distinct processing temperatures within the range spanning from the melting onset temperature of the polymer matrix to the melting peak temperature of the reinforcing polymer fiber. By conducting the uni-axial tensile tests on the UD UHMWPE-polymer-fiber-reinforced HDPE composites fabricated at different processing temperatures, it was shown that the optimal longitudinal tensile properties of the composites, comparable with glass-fiber-reinforced thermoset or thermoplastic polymers (GFRPs or GFRTPs) can be achieved when the processing temperature does not significantly exceeds the melting onset temperature of the reinforcing polymer fiber. However, when the processing temperature exceeds this threshold, the mechanical properties of the composites are significantly reduced, as evidenced by the transition in the failure morphology from the presence of significant splitting cracks to the occurrence of plastic necking due to the complete melting of the reinforcing polymer fibers in a composite. Particularly, the ductile behavior of the optimal thermoplastic PFRPs investigated in this study is superior than that of carbon-fiber-reinforced thermoset or thermoplastic polymers (CFRPs or CFRTPs) and even GFRPs and GFRTPs. This study not only provides valuable insights into the proper fabrication of high-performance thermoplastic PFRPs but also offers useful experimental data that can aid in the validation and development of computational models, particularly those related to processing modeling.

Qiao, Yao↗