Engineering topics

Shamroth, S. J.

Publications and source records attributed to Shamroth, S. J..

At least 19 records

NASA NTRS1994

A Combined Experimental/Computational Study of Flow in Turbine Blade Cooling Passage

Laser velocimetry was utilized to map the velocity field in a serpentine turbine blade cooling passage at Reynolds and Rotation numbers of up to 25.000 and 0.48. These results were used to assess the combined influence of passage curvature and Coriolis force on the secondary velocity field generated. A Navier-Stokes code (NASTAR) was validated against incompressible test data and then used to simulate the effect of buoyancy. The measurements show a net convection from the low pressure surface to high pressure surface. The interaction of the secondary flows induced by the turns and rotation produces swirl at the turns, which persisted beyond 2 hydraulic diameters downstream of the turns. The incompressible flow field predictions agree well with the measured velocities. With radially outward flow, the buoyancy force causes a further increase in velocity on the high pressure surface and a reduction on the low pressure surface. The results were analyzed in relation to the heat transfer measurements of Wagner et al. (1991). Predicted heat transfer is enhanced on the high pressure surfaces and in turns. The incompressible flow simulation underpredicts heat transfer in these locations. Improvements observed in compressible flow simulation indicate that the buoyancy force may be important.

Tse, D. G. N.↗

NASA NTRS1990

Navier-Stokes simulation of transonic blade-vortex interactions

Transonic strong blade-vortex interaction is numerically analyzed by solving the unsteady two-dimensional Navier-Stokes equations using an iterative implicit second order scheme. The dominant processes during the interaction are the development of large transverse pressure gradients in the upper leading edge region and the development of disturbances at the root of the lower surface shock wave. As a result of this interaction, high pressure pulses are emitted from the leading edge, and acoustic waves are radiated from the lower surface in a region originally occupied by a supersonic pocket. In addition, severe load variations occur when the vortex is within one chord length of the blade.

Liu, N.-S.↗

NASA NTRS1990

Two- and three-dimensional blade vortex interactions

A three-dimensional time dependent Navier-Stokes analysis was applied to the rotor blade vortex interaction (BVI) problem. The numerical procedure is an iterative implicit procedure using three point central differences to represent spatial derivatives. A series of calculations were made to determine the time steps, pseudo-time steps, iterations, artificial dissipation level, etc. required to maintain a nondissipative vortex. Results show the chosen method to have excellent non-dissipative properties provided the correct parameters are chosen. This study was used to set parameters for both two- and three-dimensional blade vortex interaction studies. The two-dimensional study considered the interaction between a vortex and a NACA0012 airfoil. The results showed the detailed physics during the interaction including the pressure pulse propagating from the blade. The simulated flow physics was qualitatively similar to that experimentally observed. The 2-D BVI phenomena is the result of the buildup and violent collapse of the shock waves and local supersonic pockets on the blade surfaces. The resulting pressure pulse build-up appears to be centered at the blade leading edge. The three-dimensional interaction study considered the case of a vortex at 20 deg incidence to the blade leading edge. Although the qualitative results were similar to that of the two-dimensional interaction, details clearly showed the three-dimensional nature of the interaction process.

Davoudzadeh, F.↗

NASA NTRS1990

Reciprocal interactions of hairpin-shaped vortices and a boundary layer

The present effort simulates the flow dynamics resulting from hairpin-shaped vortices in a boundary layer through the solution of the time-dependent, three-dimensional, compressible Navier-Stokes equations. Two simulations have been carried out. In the first case, the initial condition contains only one imposed hairpin-shaped vortex. In the second case, there are two incipient vortices separated by a short distance in the streamwise direction. The results add to the detailed understanding of the dynamic role of hairpin vortices in the entrainment, production and continual replenishment of turbulent structure, as well as the process of the interaction, intertwining and eventual conglomeration of vortices in boundary layers.

Liu, N.-S.↗

NASA NTRS1987

Two- and three-dimensional turbine blade row flow field simulations

Work performed in the numerical simulation of turbine passage flows via a Navier-Stokes approach is discussed. Both laminar and turbulent simulations in both two and three dimensions are discussed. An outline of the approach, background, and an overview of the results are given.

Buggeln, R. C.↗

NASA NTRS1987

Calculation of helicopter rotor blade/vortex interaction by Navier-Stokes procedures

Interactions of a modern rotor blade with concentrated tip vortices from the previous blades can have a significant influence on the airloads and the aeroacoustics of a helicopter. A better understanding of the blade/vortex interaction process and a method of analyzing its flow field would provide valuable help in the design of helicopters. The work discussed herein represents an initial effort in applying a 3-D, time-dependent Navier-Stokes simulation to the blade vortex interaction problem. The numerical approach is the Linearized Block Implicit (LBI) technique. In this initial effort, consideration is given to the interaction of a wing of idealized geometry and a vortex whose axis is aligned at an arbitrary angle to the wing. The calculations are made for laminar, subsonic flow, and show the time dependent pressure distribution and flow fields resulting from the interaction.

Kim, Y.-N.↗

NASA NTRS1986

Turbine stator flow field simulations

The increased capability and accessibility of modern computers, coupled with increasingly sophisticated and accurate numerical and physical modeling, has led to a marked impact of numerical simulations upon current turbine design and research problems. The turbine section represents a considerable challenge as it contains significant regions of complex three-dimensional flow, including both aerodynamic and heat transfer phenomena. The focus of the present effort is the development of an efficient and accurate three-dimensional Navier-Stokes calculation procedure for application to the turbine stator and rotor problems. In particular, an effective procedure is sought which: (1) adequately represents the flow physics, (2) allows for sufficient resolution in regions of small length scale, and (3) has sufficiently good convergence properties so as to allow use on a regular basis.

Buggeln, R. C.↗

NASA NTRS1986

A three-dimensional viscous flow analysis for the helicopter tip vortex generation process about square and round tipped blades

The tip vortex flow field occurring in the vicinity of the tip region of a helicopter rotor blade is a very complicated three-dimensional, viscous flow phenomenon. The details of the flow in the tip region can have a major effect in determining the generated rotor noise and can significantly effect the performance and dynamic loading of the rotor blade. The three-dimensional viscous subsonic tip vortex generation processes is investigated by a numerical procedure which allows spatial forward-marching integration, utilizing flow approximations from the velocity-decomposition approach of Briley and McDonald. The approach has been applied to compute the laminar and turbulent tip vortex flows for a constant thickness slab airfoil with a square tip, a constant thickness slab airfoil with a half round tip and a NACA 0012 airfoil with a half round tip. The basic mechanism of the tip vortex generation process as well as the prediction of vortex appearance, strength and secondary flow shown by the calculations are in qualitative agreement with experimental results.

Lin, S.-J.↗

NASA NTRS1985

Flow in a model turbine stator

In view of the complex nature of the flowfield in the hot section of gas turbine engines, the need to predict heat transfer and flow losses, the possible appearance of separation and strong secondary flows, etc., the present effort is focusing upon a Navier-Stokes approach to the three dimensional turbine stator problem. The advantages of a full Navier-Stokes approach are clear since when combined with a suitable turbulence model these equations represent the flow and heat transfer physics. In particular, the Navier-Stokes equations accurately represent possible separated regions and regions of significant secondary flow. In addition, the Navier-Stokes approach allows representation of the entire flow field by a single set of equations, thus avoiding problems associated with representing different regions of the flow by different equations and then matching flow regions.

Buggeln, R. C.↗

NASA NTRS1985

Calculation of steady and unsteady airfoil flow fields via the Navier-Stokes equations

A compressible time-dependent procedure for the two-dimensional ensemble averaged Navier-Stokes equations has been applied to the isolated airfoil problem in steady and unsteady flows. The procedure solves the governing equations via the linearized block implicit technique. Turbulence is modeled either via a mixing length or turbulence energy approach. The equations are solved in general non-orthogonal form with no-slip boundary conditions applied at the airfoil surface. Results are presented for airfoils at constant incidence, an airfoil in ramp motion and an airfoil oscillating through a dynamic stall loop. In general, steady converged solutions are obtained within 70 time steps over the range of Mach numbers considered. Comparisons with measured data show good agreement between computation and measurement.

Shamroth, S. J.↗

NASA NTRS1985

On the application of a hairpin vortex model of wall turbulence to trailing edge noise prediction

The goal is to develop a technique via a hairpin vortex model of the turbulent boundary layer, which would lead to the estimation of the aerodynamic input for use in trailing edge noise prediction theories. The work described represents an initial step in reaching this goal. The hairpin vortex is considered as the underlying structure of the wall turbulence and the turbulent boundary layer is viewed as an ensemble of typical hairpin vortices of different sizes. A synthesis technique is examined which links the mean flow and various turbulence quantities via these typical vortices. The distribution of turbulence quantities among vortices of different scales follows directly from the probability distribution needed to give the measured mean flow vorticity. The main features of individual representative hairpin vortices are discussed in detail and a preliminary assessment of the synthesis approach is made.

Liu, N. S.↗

NASA NTRS1985

A three-dimensional viscous flow analysis for the helicopter tip vortex generation problem

The tip vortex flow field occurring in the vicinity of the tip region of a a helicopter rotor blade is a very complicated three-dimensional, viscous flow phenomenon. The details of the flow in the tip region can have a major effect in determining the generated rotor noise and can significantly affect the performance and dynamic loading of the rotor blade. The three-dimensional viscous subsonic tip vortex generation processes is investigated by a numerical procedure which allows spatial forward-marching integration, utilizing flow approximations from the velocity-decomposition approach of Briley and McDonald. The approach has been applied to compute the laminar and turbulent tip vortex flows for a constant thickness slab airfoil with a square tip, a constant thickness slab airfoil with a half round tip and a NACA 0012 airfoil with a half round tip. The basic mechanism of the tip vortex generation process as well as the prediction of vortex appearance, strength and secondary flow shown by the calculations are in qualitative agreement with experimental results.

Lin, S. J.↗

NASA NTRS1985

Turbine Vane External Heat Transfer. Volume 2. Numerical Solutions of the Navier-stokes Equations for Two- and Three-dimensional Turbine Cascades with Heat Transfer

The application of the time-dependent ensemble-averaged Navier-Stokes equations to transonic turbine cascade flow fields was examined. In particular, efforts focused on an assessment of the procedure in conjunction with a suitable turbulence model to calculate steady turbine flow fields using an O-type coordinate system. Three cascade configurations were considered. Comparisons were made between the predicted and measured surface pressures and heat transfer distributions wherever available. In general, the pressure predictions were in good agreement with the data. Heat transfer calculations also showed good agreement when an empirical transition model was used. However, further work in the development of laminar-turbulent transitional models is indicated. The calculations showed most of the known features associated with turbine cascade flow fields. These results indicate the ability of the Navier-Stokes analysis to predict, in reasonable amounts of computation time, the surface pressure distribution, heat transfer rates, and viscous flow development for turbine cascades operating at realistic conditions.

Yang, R. J.↗

NASA NTRS1985

Users manual for coordinate generation code CRDSRA

Generation of a viable coordinate system represents an important component of an isolated airfoil Navier-Stokes calculation. The manual describes a computer code for generation of such a coordinate system. The coordinate system is a general nonorthogonal one in which high resolution normal to the airfoil is obtained in the vicinity of the airfoil surface, and high resolution along the airfoil surface is obtained in the vicinity of the airfoil leading edge. The method of generation is a constructive technique which leads to a C type coordinate grid. The method of construction as well as input and output definitions are contained herein. The computer code itself as well as a sample output is being submitted to COSMIC.

Shamroth, S. J.↗

NASA NTRS1985

User's manual for airfoil flow field computer code SRAIR

A two dimensional unsteady Navier-Stokes calculation procedure with specific application to the isolated airfoil problem is presented. The procedure solves the full, ensemble averaged Navier-Stokes equations with turbulence represented by a mixing length model. The equations are solved in a general nonorthogonal coordinate system which is obtained via an external source. Specific Cartesian locations of grid points are required as input for this code. The method of solution is based upon the Briley-McDonald LBI procedure. The manual discusses the analysis, flow of the program, control steam, input and output.

Shamroth, S. J.↗

NASA NTRS1985

Calculations of two and three-dimensional transonic cascade flow fields using the Navier-Stokes equations

The multidimensional, ensemble-averaged, compressible, time-dependent Navier-Stokes equations have been used to study the turbulent flow field in two and three-dimensional turbine cascades. The viscous regions of the flow were resolved and non-slip boundary conditions were utilized on solid surfaces. The calculations were performed in a constructive 'O'-type grid which allows representation of the blade rounded trailing edge. Converged solutions were obtained in relatively few time steps (about 80-150) and comparisons for both surface pressure and heat transfer showed good agreement with data. The three-dimensional turbine cascade calculation showed many of the expected flow-field features.

Weinberg, B. C.↗

NASA NTRS1985

A solution procedure for two- and three-dimensional unsteady viscous flows

An efficient computational procedure for solving three-dimensional unsteady turbulent flows is described. The consistently split Linearized Block Implicit (LBI) scheme is used in conjunction with the QR operator scheme to solve an approximate form of the Navier-Stokes equations in generalized nonorthogonal coordinates employing physical velocity components. As a demonstration calculation the turbulent oscillating flow over a flat plate corresponding to the experiment of Karlsson is considered in both two and three dimensions. New inflow boundary conditions are proposed which yield physically plausible solutions near the upstream boundary. The results obtained agree both qualitatively and quantitatively with Karlsson's data and shed new light on the controversy concerning the interpretation of the skin friction phase angle as a function of reduced frequency.

Weinberg, B. C.↗

NASA NTRS1985

On hairpin vortices as model of wall turbulence structure

A model of the hairpin vortex has been constructed and used in two distinct but related approaches. The first approach is kinematic in nature in which a synthesis procedure using hairpin vortices to provide a quantitative link between mean flow quantities and the statistical quantities of near wall turbulence has become developed. The second approach is dynamic in nature, and the evolution of an incipient 'representative' hairpin vortex as well as the distortion of a background laminar boundary layer flow, in which the hairpin vortex is immersed, has been simulated by numerical solution of the unsteady, three-dimensional Navier-Stokes equations.

Liu, N.-S.↗