Search NASA⌕ Search

Engineering topics

Shapiro, W.

Publications and source records attributed to Shapiro, W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Analysis and design of a gas-lubricated, sectored, floating ring seal

Helium buffered floating-ring seals used in cryogenic turbopumps are subject to large temperature variations, shaft centrifugal growth, and dynamic shaft excursions. To prevent dangerous contact friction over a wide range of operating conditions generally requires liberal clearances with consequent high leakage. Reduction of helium consumption translates into lower space vehicle helium storage requirements and thus increased payload. A hydrostatic sectored floating-ring seal is described with self-adjusting clearance capabilities that enables the seal to operate with small clearances over the operating range to minimize leakage.

Shapiro, W.↗
NASA NTRS1985

Advanced seals for Liquid Oxygen (LOX) turbopumps

Reliability, life and vehicle pay load can be enhanced by improved seals on space vehicle propulsion systems. Development of two types of fluid-film seals for application to advanced LOX turbomachines are summarized. The first is a floating ring, helium buffered seal whose function is to exclude intrusion of liquid oxygen (LOX) into the turbine drive. The other is a spiral groove, LOX, face-type configuration designed to break down pressure and minimize leakage of LOX. The Rayleigh-step, floating ring gas seals require low clearances to minimize leakage and stiff films to assure tracking excursions of the rotor and to overcome Coulomb friction between the rings and housings. The design and test results of these buffer seals are described. Results indicate significant performance improvement over seals used on contemporary engines. The possibilities of reducing helium storage requirements and thus increasing payload appear promising. A unique configuration of spiral groove LOX seal was required to avoid detrimental vaporization in the flow path. It was found that fluid turbulence and inertia influence groove geometry and in particular groove depth must be much greater than spiral groove seals using conventional fluids.

Shapiro, W.↗
NASA NTRS1984

Development of Gas-Lubricated Pistons for Heavy Duty Diesel Engine Technology Program

Static testing of a segmented, gas-lubricated, piston-ring was accomplished. The ring utilizes high-pressure gas generated during the diesel cycle to energize a hydrostatic gas film between the piston and cylinder liner. The configuration was deficient in overall performance, because all segments of a ring set failed to form a fluid-film simultaneously, when exposed to internal preload. The difficulty was traced to the moment balance required to prevent the segments from overturning and contacting the cylinder walls. Some individual sectors formed a film and performed well in every respect including load capability to 6,000 N. These results produce optimism as to the ultimate feasibility of hydrostatic, gas-lubricated piston rings. In addition to test results, the principles of operation, and theoretical developments are presented. Breathable liner concepts are suggested for future consideration. In these configurations, solid hydrostatic pistons are coupled with flexible liners that elastically deform to form a gas-film under hydrostatic pressurization. Breathable liners afford the mechanical simplicity required for mass produced engines, and initial examination indicates satisfactory operation.

Shapiro, W.↗
NASA NTRS1983

Design analysis of Rayleigh-step floating-ring seals

The analysis and design of a 50-mm diameter floating-ring helium buffer seal are described. The seal rings incorporated Rayleigh-step lift pads to provide hydrodynamic forces to separate the rings from the shaft. Maximum surface speed is 183 m/s (600 fps) and maximum buffer gas pressure is 1389 kPa (200 psia). An operating range map was computed as a function of speed and pressure. Contradictory problems arise due to excessive friction preventing ring tracking at low-speed, high-pressure conditions and insufficent friction to retard inertia driven motions at high-speed, low-pressure conditions. Steady-state and dynamic analyses and performance are described, as well as the results of thermal studies.

Artiles, A.↗
NASA NTRS1983

Analysis of spiral-groove face seals for liquid oxygen

Analyses and predicted performance of a 50-mm diameter, spiral-groove face seal to seal liquid oxygen at 5.17 MPa pressure, and operating at surface speeds of 183 m/s are described. The pressure-balanced spiral-groove concept is introduced that circulates spiral-groove flow independent of leakage flow. Independent flow paths preclude overheating from vaporization and consequent flow blockage. The analysis accounts for fluid turbulence and inertia, thermoelastic distortions, and dynamic response. An operating-range map was developed as a function of speed and pressure. The fluid-film analysis is summarized in the Appendix.

Shapiro, W.↗
NASA NTRS1974

Steady-state and dynamic analysis of a jet engine, gas lubricated shaft seal

Dynamic response of a gas-lubricated, jet-engine main shaft seal was analytically established as a function of collar misalignment and secondary seal friction. Response was obtained by a forward integration-in-time (time-transient) scheme, which traces a time history of seal motions in all its degrees of freedom. Results were summarized in the form of a seal tracking map which indicated regions of acceptable collar misalignments and secondary seal friction. Methodology, results and interpretations are comprehensively described.

Shapiro, W.↗
NASA NTRS1974

Start-stop testing of two self-acting air-lubricated spiral groove thrust bearing coatings

Start-stop tests were conducted on air-lubricated spiral-groove thrust bearings. Application of a matrix-bonded molybdenum disulfide (MoS2) coating over a porous chrome oxide coating resulted in significantly lower friction, compared to bearings coated with chrome oxide only. The MoS2 coated bearing sustained 15,000 start-stop cycles at a maximum of 3600 rpm. Each cycle was 15 seconds on, 30 seconds off. The chrome oxide coated bearing failed by local welding after 2030 cycles. Both types of coatings exhibited early failures under higher thrust loads when operating films were insufficient to sustain the load without overheating.

Dunfee, J. D.↗
NASA NTRS1972

Steady-state and dynamic performance of a gas-lubricated seal

Steady-state and dynamic performance of a gas-lubricated, self-acting face seal was determined using numerical methods based on a variable grid, finite-difference, time-transient procedure. Results were obtained for a gas turbine main shaft seal operating at 206.9 newton per square centimeter (300 psi) sealed air pressure and 152.4 meters per second (500 ft/sec) sliding velocity. Analysis of the seal dynamics revealed that the response of the seal nosepiece to runout of the seat face is markedly affected by secondary seal friction and by nosepiece inertia. The nosepiece response was determined for various levels of secondary seal friction and seat face runout magnitudes.

Colsher, R.↗