Engineering topics

Shi, Pei

Publications and source records attributed to Shi, Pei.

4 records

DOE OSTI2024

Hybrid polymer network cathode-enabled soluble-polysulfide-free lithium–sulfur batteries

Among the emerging 'beyond lithium-ion' technologies for maximized sustainability, lithium-sulfur (Li-S) is a favoured chemistry because of its exceptional energy density from the conversion of sulfur, an element in abundant supply. However, the dissolution of several intermediate polysulfides formed during conversion leads to rapid performance degradation over cycling. Here, in this study, we address this issue by sulfurizing a hybrid polymer network with polyphosphazene and carbon as a cathode for Li-S batteries. With rich sites to re-bond and adsorb dissociative sulfur species, this hybrid polymer network circumvents the formation of soluble polysulfides and enables a unique, reversible inserting conversion reaction. Thus, our cathode delivers both high capacity (~900 mAh g -1 cathode ) and excellent cycling stability in Li-S coin cells, with a pouch cell demonstration of projected energy density of ~300 Wh kg -1 and 84.9% capacity retention after 150 cycles. The strategy can be extended to other cost-effective, recyclable polymers, advancing sulfur-based batteries towards practical energy storage application.

25 ENERGY STORAGE↗

DOE OSTI2023

Realizing high-capacity all-solid-state lithium-sulfur batteries using a low-density inorganic solid-state electrolyte

Abstract Lithium-sulfur all-solid-state batteries using inorganic solid-state electrolytes are considered promising electrochemical energy storage technologies. However, developing positive electrodes with high sulfur content, adequate sulfur utilization, and high mass loading is challenging. Here, to address these concerns, we propose using a liquid-phase-synthesized Li 3 PS 4 -2LiBH 4 glass-ceramic solid electrolyte with a low density (1.491 g cm −3 ), small primary particle size (~500 nm) and bulk ionic conductivity of 6.0 mS cm −1 at 25 °C for fabricating lithium-sulfur all-solid-state batteries. When tested in a Swagelok cell configuration with a Li-In negative electrode and a 60 wt% S positive electrode applying an average stack pressure of ~55 MPa, the all-solid-state battery delivered a high discharge capacity of about 1144.6 mAh g −1 at 167.5 mA g −1 and 60 °C. We further demonstrate that the use of the low-density solid electrolyte increases the electrolyte volume ratio in the cathode, reduces inactive bulky sulfur, and improves the content uniformity of the sulfur-based positive electrode, thus providing sufficient ion conduction pathways for battery performance improvement.

25 ENERGY STORAGE↗

DOE OSTI2022

A Superior Carbonate Electrolyte for Stable Cycling Li Metal Batteries Using High Ni Cathode

Li metal batteries pairing Li metal anode with high-nickel layer structured oxide cathode are a promising energy storage technology to achieve high energy density. To obtain long cycling life for Li metal batteries, the electrolyte plays a pivotal role in stabilizing both the Li metal anode and the high-nickel cathode upon electrochemical cycling. Herein, we report a carbonate electrolyte that enables a Li||LiNi 0.8 Mn 0.1 Co 0.1 O 2 pouch cell to achieve a high gravimetric energy density of 366 Wh/kg and unprecedented cycling stability with 80% capacity retention after 335 cycles. Here, the 19 F quantitative nuclear magnetic resonance spectroscopy and interface characterization demonstrate that FEC and LiDFOB can reduce the consumption rate of each other and the electrolyte, form a robust LiF-rich SEI on Li metal anode, and improve the microstructure integrity of the high-nickel cathode.

25 ENERGY STORAGE↗

DOE OSTI2021

Multifunctional Li-ion Conducting Interfacial Materials for Lithium Metal Batteries”

The overall approach will focus on the development and optimization of synthesis methods and precursors for multifunctional Li-ion conducting interfacial materials, protective layer composition, and protective layer fabrication methods. This will be accompanied by property measurement and characterization (conductivity, mechanical properties, etc.) for the protective layer on Li metal, along with cell testing.

25 ENERGY STORAGE↗