Search NASA⌕ Search

Engineering topics

Shi, Rongpei

Publications and source records attributed to Shi, Rongpei.

At least 19 records

Phase field modeling of shearing processes of a dual-lobed γ"|γ'|γ" coprecipitate

The Ni-based superalloy IN718 is one of the most widely used commercial alloy in the aerospace industry since its development in 1960s. The excellent mechanical properties have been attributed in a great deal to strengthening by coherent γ' and γ" precipitates. The deformation mechanisms of these two phases have been well studied individually. Recent experimental characterization has shown coprecipitates of these two phases in a variety of morphologies and it was argued that these coprecipitates may lead to improved strengthening as compared to their monolithic counterparts. However, the deformation mechanisms of these coprecipitates are still not well understood. In this study, we performed microscopic phase field simulations, with generalized-stacking-fault (GSF) energy surfaces from ab initio calculations as inputs, to systematically study the shearing processes of a periodical array of dual-lobed coprecipitates as well as monolithic precipitates. We found that the coupling between the γ' and γ" phases in the coprecipitates forces dislocations to take high energy shearing pathways in both phases that would not occur if they were in monolithic forms. The coupling also creates stacking fault configurations in the coprecipitates that require high stress to form. Thus, the presence of coprecipitates in general should increase the resistance to dislocation shearing and lead to higher strength levels. Various fault configurations observed during the shearing process are documented as a reference for future comparison with experimental observations. The link between stacking fault shearing and microtwinning is also discussed. Here, the mechanisms analyzed in this study deepens our understanding of coprecipitation effects on alloy strength and may form a cornerstone for multi-precipitate strengthened alloy design strategies.

36 MATERIALS SCIENCE↗

Oxide‐Based Solid‐State Batteries: A Perspective on Composite Cathode Architecture

Abstract The garnet‐type phase Li 7 La 3 Zr 2 O 12 (LLZO) attracts significant attention as an oxide solid electrolyte to enable safe and robust solid‐state batteries (SSBs) with potentially high energy density. However, while significant progress has been made in demonstrating compatibility with Li metal, integrating LLZO into composite cathodes remains a challenge. The current perspective focuses on the critical issues that need to be addressed to achieve the ultimate goal of an all‐solid‐state LLZO‐based battery that delivers safety, durability, and pack‐level performance characteristics that are unobtainable with state‐of‐the‐art Li‐ion batteries. This perspective complements existing reviews of solid/solid interfaces with more emphasis on understanding numerous homo‐ and heteroionic interfaces in a pure oxide‐based SSB and the various phenomena that accompany the evolution of the chemical, electrochemical, structural, morphological, and mechanical properties of those interfaces during processing and operation. Finally, the insights gained from a comprehensive literature survey of LLZO–cathode interfaces are used to guide efforts for the development of LLZO‐based SSBs.

25 ENERGY STORAGE↗

Towards understanding particle rigid-body motion during solid-state sintering

A quantitative understanding of particle rigid body (RB) motion that inherently accompanies grain boundary (GB) diffusion is highly desirable to understand and control the dynamic interplay between coarsening and densification during solid state sintering. In this work, by computer simulation using a multi-phase-field approach, we analyze systematically the roles played by each of these processes at different stages of the shrinkage of the internal pore in a three-particle green body as a function of particle size as well as thermodynamic and kinetic factors of interfaces. We demonstrate that particle RB translation promotes both neck growth, and pore rounding and shrinkage. Moreover, the forces acting at GBs and pulling neighboring particles towards one another dynamically evolve as particles fuse. In contrast, particle RB rotation has no contribution to pore shrinkage. The translational force acting on an individual particle varies with not only its size, but also the number and sizes of its neighboring particles.

36 MATERIALS SCIENCE↗

Nondiffractive beam shaping for enhanced optothermal control in metal additive manufacturing

High thermal gradients and complex melt pool instabilities involved in powder bed fusion–based metal additive manufacturing using focused Gaussian-shaped beams often lead to high porosity, poor morphological quality, and degraded mechanical performance. We show here that Bessel beams offer unprecedented control over the spatiotemporal evolution of the melt pool in stainless steel (SS 316L) in comparison to Gaussian beams. Notably, the nondiffractive nature of Bessel beams enables greater tolerance for focal plane positioning during 3D printing. We also demonstrate that Bessel beams significantly reduce the propensity for keyhole formation across a broad scan parameter space. High-speed imaging of the melt pool evolution and solidification dynamics reveals a unique mechanism where Bessel beams stabilize the melt pool turbulence and increase the time for melt pool solidification, owing to reduced thermal gradients. Consequently, we observe a distinctively improved combination of high density, reduced surface roughness, and robust tensile properties in 3D-printed test structures.

36 MATERIALS SCIENCE↗

A mesoscopic digital twin that bridges length and time scales for control of additively manufactured metal microstructures

We present our recent development of an integrated mesoscale digital twin (DT) framework for relating processing conditions, microstructures, and mechanical responses of additively manufactured (AM) metals. In particular, focusing on the laser powder bed fusion technique, we describe how individual modeling and simulation capabilities are coupled to investigate and control AM microstructural features at multiple length and time scales. We review our prior case studies that demonstrate the integrated modeling schemes, in which high-fidelity melt pool dynamics simulations provide accurate local thermal profiles and histories to subsequent AM microstructure simulations. We also report our new mechanical response modeling results for predicted AM microstructures. In addition, we illustrate how our DT framework has been validated through modeling–experiment integration, as well as how it has been practically utilized to guide and analyze AM experiments. Finally, we share our perspectives on future directions of further development of the DT framework for more efficient, accurate predictions and wider ranges of applications.

36 MATERIALS SCIENCE↗

Nucleation and growth of α phase in a metastable β-Titanium Ti-5Al-5Mo-5V-3Cr alloy: Influence from the nano-scale, ordered-orthorhombic O" phase and α compositional evolution

We investigated the nucleation and growth of α precipitates in the presence of nano-scale, titanium-rich, ordered-orthorhombic O" precipitates formed during heating at 5 °C/min to 400 °C in a metastable β-Ti alloy, Ti-5Al-5Mo-5V-3Cr. The O" precipitates are found to assist α nucleation by serving as preferential nucleation sites. In the very initial stages of its precipitation, the α phase is found to have formed via a coupled diffusional-displacive mode as titanium-rich plates. At this stage, aluminum partitions equally between the β matrix and the growing α precipitates, but slowly diffuses up-hill into the α phase during isothermal aging at 400 °C for 15 h. The interplay between such pre-formed metastable phases and α can be exploited to tailor the microstructure, by refining the α distribution, and consequently improve the mechanical properties of β-Ti alloys. Finally, our work paves the way for exploiting this cascade of metastable phases for further microstructural engineering of β-Ti alloys.

36 MATERIALS SCIENCE↗

Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

Garnet-type solid electrolytes, such as Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO), are promising materials for solid-state batteries, but processing remains a challenge, in part due to the high sintering temperature required for densification. Additionally, this temperature can be lowered by decreasing the initial particle size via solvent-assisted ball milling, but the relationship between solvent choice, particle properties, sintering behavior, and ionic conductivity is not well understood. In this work, we systematically explore these parameters, showing that milling in commonly used protic solvents, such as alcohols, effectively decreases the particle size but results in lithium loss (through Li + /H + exchange) that leads to poor sintering. By contrast, milling in aprotic solvents with surfactant reduces the particle size to ~220 nm without lithium loss, enabling the fabrication of dense samples (5.1 g/cm 3 ) with good ionic conductivity (0.43 mS/cm at 25 °C) at a lower sintering temperature (1000 °C). We compare ionic conductivities and activation energies for samples prepared with different particle sizes and sintering temperatures and use multiphase-field simulations to identify the mass transport and microstructural mechanisms responsible for the observed sintering dependence on particle size. These results further clarify the relationship between processing parameters and performance and represent important progress toward overcoming fabrication challenges for these materials.

25 ENERGY STORAGE↗

Periodic Porous 3D Electrodes Mitigate Gas Bubble Traffic during Alkaline Water Electrolysis at High Current Densities

We report alkaline water electrolysis at high current densities is plagued by gas bubble generation and trapping in stochastic porous electrodes (e.g., Ni foams), which causes a significant reduction in the number of electrolyte accessible catalyst active sites. Here, 3D printed Ni (3DPNi) electrodes with highly controlled, periodic structures are reported that suppress gas bubble coalescence, jamming, and trapping and, hence, result in rapid bubble release. The 3DPNi electrodes decorated with carbon-doped NiO achieve a high current density of 1000 mA cm -2 in 1.0 m KOH electrolyte at hydrogen evolution reaction and oxygen evolution reaction overpotentials of 245 and 425 mV, respectively. This work demonstrates a new approach to the deterministic design of 3D electrodes to facilitate rapid bubble transport and release to enhance the total electrode catalytic activity at commercially relevant current densities.

08 HYDROGEN↗

Critical nuclei at hetero-phase interfaces

Two-step nucleation, in which a metastable intermediate phase acts as a precursor for nucleating a thermodynamically stable phase, has been widely observed in many materials systems and solid-state reactions. Among the advantages of two-step nucleation is that the stable phase may nucleate heterogeneously at the hetero-phase interface between the original and the precursory phases. Although heterogeneous nucleation (HN) theories for homo-phase grain boundaries and inert surfaces are well established, our understanding of HN at reactive hetero-phase interfaces remains incomplete. This deficiency stems from the discontinuity of the chemical potential driving force across the hetero-phase interface, which profoundly affects the fundamental properties of the nucleus in a way that is not properly accounted for in existing models. In this work, we incorporate these effects to extend the classical nucleation theory to HN at hetero-phase interfaces. Our extended model demonstrates that the nucleus shape along the minimum energy path is strongly size-dependent, and this additional degree of freedom can result in the reduction of the critical nucleus volume and associated activation energy barrier by orders of magnitude relative to conventional predictions. The simulation results are used to construct a sensitivity map in the parameter space of interfacial energy and bulk driving force ratios, which quantifies the difference in nucleation barriers predicted by different models.

36 MATERIALS SCIENCE↗

ω-Assisted α nucleation in a metastable β titanium alloy

Here, we explore mechanisms of ω-assisted α nucleation for microstructure refinement in a metastable β titanium alloy, Ti-20V (wt%). In particular, we analyze quantitatively the individual and combined effects of concentration and stress fields associated with a growing isothermal ω precipitate and the potency of the ω/β interface on the activation energy barrier for α nucleation as a function of the ω precipitate size and coherency state. We find that the complex interplay among these three factors determines the most potent ω particle size for inducing α nucleation and the most favorable nucleation site.

36 MATERIALS SCIENCE↗

Integrated Simulation Framework for Additively Manufactured Ti-6Al-4V: Melt Pool Dynamics, Microstructure, Solid-State Phase Transformation, and Microelastic Response

In this work, to accelerate the establishment of fundamental understanding of the additive manufacturing (AM) process and its influence on microstructural evolution and related properties, we develop a multiphysics and multiscale modeling framework that integrates: (1) a high-fidelity powder-scale three-dimensional simulation of transient heat transfer and melt flow dynamics, (2) cellular automaton simulation of solidification grain structure and texture, (3) phase-field modeling of precipitation and dissolution of second-phase precipitate during repeated thermal cycles, and (4) microstructure-based micro- and mesoscopic elastic response calculation. Using Ti-6Al-4V as a model system, we demonstrate the application of the integrated framework to simulate complex microstructure evolution during a single-track laser powder bed fusion process and the associated mechanical response. Our modeling framework successfully captures the solidification β grain structure as a function of laser power and scanning speed, α precipitation upon subsequent cooling with different rates, and elastic response of the resulting (α + β) two-phase microstructure. The key features of solidification and second-phase precipitate microstructures, and their dependence on processing parameters, agree well with existing experimental observations. Finally, the established modeling framework is generally applicable to other metallic materials fabricated by AM.

36 MATERIALS SCIENCE↗

A New Superalloy Enabling Heavy Duty Gas Turbine Wheels for Improved Combined Cycle Efficiency

The drive to increase combined cycle turbine efficiency from 62% to 65% for the next-generation advanced cycle requires a new heavy duty gas turbine wheel material capable of operating at 1200°F and above. Current wheel materials are limited by the stability of their major strengthening phase (gamma double prime), which coarsens at temperatures approaching 1200°F, resulting in a substantial reduction in strength. More advanced gamma prime superalloys, such as those used in jet engine turbine disks, are also not suitable due to size constraints; the gamma prime phase overages during the slow cooling rates inherent in processing thick-section turbine wheels. The current program addresses this need by screening two new alloy design concepts. The first concept exploits a gamma prime/gamma double prime coprecipitation reaction. Through manipulation of alloy chemistry, coprecipitation is controlled such that gamma double prime is used only to slow the growth of gamma prime during slow cooling, preventing over-aging, and allowing for subsequent heat treatment to maximize strength. In parallel, phase field modeling provides fundamental understanding of the coprecipitation reaction. The second concept uses oxide dispersion strengthening to improve on two existing alloys that exhibit excellent hold time fatigue crack growth resistance, but have insufficient strength to be considered for gas turbine wheels. Mechanical milling forces the dissolution of starting oxide powders into a metal matrix allowing for solid state precipitation of new, nanometer scale oxides that are effective at dispersion strengthening.

36 MATERIALS SCIENCE↗