Enhancing charge-emitting shallow traps in metal halide perovskites by >100 times by surface strain
Not Available
Zhou, Ying (ORCID:0000000302528055)↗
Engineering topics
Shi, Zhifang
Publications and source records attributed to Shi, Zhifang.
Identification and Suppression of Point Defects in Bromide Perovskite Single Crystals Enabling Gamma‐Ray Spectroscopy
Abstract Methylammonium lead tribromide (MAPbBr 3 ) stands out as the most easily grown wide‐band‐gap metal halide perovskite. It is a promising semiconductor for room‐temperature gamma‐ray ( γ ‐ray) spectroscopic detectors, but no operational devices are realized. This can be largely attributed to a lack of understanding of point defects and their influence on detector performance. Here, through a combination of crystal growth design and defect characterization, including positron annihilation and impedance spectroscopy, the presence of specific point defects are identified and correlated to detector performance. Methylammonium (MA) vacancies, MA interstitials, and Pb vacancies are identified as the dominant charge‐trapping defects in MAPbBr 3 crystals, while Br vacancies caused doping. The addition of excess MABr reduces the MA and Br defects and so enables the detection of energy‐resolved γ ‐ray spectra using a MAPbBr 3 single‐crystal device. Interestingly, the addition of formamidinium (FA) cations, which converted to methylformamidinium (MFA) cations by reaction with MA + during crystal growth further reduced MA defects. This enabled an energy resolution of 3.9% for the 662 keV 137 Cs line using a low bias of 100 V. The work provides direction toward enabling further improvements in wide‐bandgap perovskite‐based device performance by reducing detrimental defects.
Ni, Zhenyi↗
Barrier reinforcement for enhanced perovskite solar cell stability under reverse bias
Stability of perovskite solar cells (PSCs) under light, heat, humidity and their combinations have been notably improved recently. However, PSCs have poor reverse-bias stability that limits their real-world application. Here we report a systematic study on the degradation mechanisms of p-i-n structure PSCs under reverse bias. The oxidation of iodide by injected holes at the cathode side initialize the reverse-bias-induced degradation, then the generated neutral iodine oxidizes metal electrode such as copper, followed by drift of Cu+ into perovskites and its reduction by injected electrons, resulting in localized metallic filaments and thus device breakdown. A reinforced barrier with combined lithium fluoride, tin oxide and indium tin oxide at the cathode side reduces device dark current and avoids the corrosion of Cu0. It dramatically increases breakdown voltage to above -20 V and improved the T90 lifetime of PSCs to ~1,000 h under -1.6 V. The modified minimodule also maintained over 90% of its initial performance after 720 h of shadow tests.
degradation mechanisms↗
Strong-Bonding Hole-Transport Layers Reduce Ultraviolet Degradation of Perovskite Solar Cells
The light-emitting diodes (LEDs) used in indoor testing of perovskite solar cells do not expose them to the levels of ultraviolet (UV) radiation that they would receive in actual outdoor use. We report degradation mechanisms of p-i-n-structured perovskite solar cells under unfiltered sunlight and with LEDs. Weak chemical bonding between perovskites and polymer hole-transporting materials (HTMs) and transparent conducting oxides (TCOs) dominate the accelerated A-site cation migration, rather than direct degradation of HTMs. An aromatic phosphonic acid, [2-(9-ethyl-9H-carbazol-3-yl)ethyl]phosphonic acid (EtCz3EPA), enhanced bonding at the perovskite/HTM/TCO region with a phosphonic acid group bonded to TCOs and a nitrogen group interacting with lead in perovskites. A hybrid HTM of EtCz3EPA with strong hole-extraction polymers retained high efficiency and improved the UV stability of perovskite devices, and a champion perovskite minimodule-independently measured by the Perovskite PV Accelerator for Commercializing Technologies (PACT) center-retained operational efficiency of >16% after 29 weeks of outdoor testing.
14 SOLAR ENERGY↗
Multifunctional entinostat enhances the mechanical robustness and efficiency of flexible perovskite solar cells and minimodules
Flexible perovskite solar cells (F-PSCs), prized for their nature of soft and high power-weight compatibility, have attracted intensive attention. However, inferior buried perovskite-substrate interfaces due to low interfacial adhesion between perovskites and substrates and large deformation of flexible substrates have greatly limited the performance of F-PSCs. Here, we add organic molecule Entinostat (ET) into hole extraction material Poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) to enhance the adhesion at the perovskite/substrate interface using the interactions of ET with perovskites, PTAA and indium tin oxide (ITO) through its multiple function groups. Meanwhile, ET added into perovskites reduces the voids at the bottom perovskite film, due to its capability to tune the crystallization of perovskites by forming adduct with lead. Consequently, the inverted small area F-PSCs achieved an efficiency of 23.4%. The flexible perovskite minimodule with an area of 9 cm 2 achieved an aperture efficiency of ~19.0% certified by National Renewable Energy Laboratory. Furthermore, the optimized unencapsulated flexible minimodule retained 84% of the initial efficiency after 5000 bending cycles and retained 90% of the initial PCE (T90) after light soaking for >750 hours.
14 SOLAR ENERGY↗
Surface-Defect-Passivation-Enabled Near-Unity Charge Collection Efficiency in Bromide-Based Perovskite Gamma-Ray Spectrum Devices
Hybrid lead halide perovskites have superior charge transport properties to all-inorganic perovskites, but high-resolution spectroscopic radiation detectors have not been realized. Here we show that surface deep traps severely limit charge collection in formamidinium lead bromide (FAPbBr3) single-crystal devices, despite having a good bulk transport property. Three types of defect on the crystal surface, namely, FA vacancies, uncoordinated lead and Pb-Pb dimers caused by bromide loss, are found to form deep traps, resulting in non-radiative charge recombinations at the metal/perovskite interface. By tailoring the passivation functional groups, we find that ammonium bromide can passivate all these three deep traps on FAPbBr3 surfaces, improving the charge collection efficiency to near unity. The comparable bulk and surface recombination lifetimes indicate that all the surface defects are effectively passivated. Surface passivation also reduces the dark current by 10 times and decreases the dark counts by ~60 times. The energy resolution of the 137Cs spectra acquired using the FAPbBr3 detectors is improved from 5.7% to 1.7% when all the surface defects are passivated without changing the bulk properties, which is the best among solution-grown semiconductor detectors. Surface passivation is stable for more than six months, and FAPbBr3 spectroscopic detectors can operate at unprecedented high temperatures of more than 130 degrees C.
gamma ray↗
Shunt mitigation toward efficient large-area perovskite-silicon tandem solar cells
Not provided.
Chemistry↗
Ammonium cations with high p K a in perovskite solar cells for improved high-temperature photostability
Phenethylammonium (PEA + ) and butylammonium (BA + ) are widely used in three-dimensional (3D) perovskites to form two-dimensional (2D) perovskites at film surfaces and grain boundaries (GBs) for defect passivation and performance enhancement. Here, we show that these cations are unstable with 3D formamidinium (FA + )-containing perovskites under high-temperature light soaking. PEA + and BA + are found to deprotonate to amines, which then react with FA + to produce (phenethylamino)methaniminium (PEAMA + ) and (butylamino)methaniminium (BAMA + ), respectively, severely limiting device high-temperature photostability. Furthermore, removing these cations greatly improves the photostability but compromises device efficiency by leaving non-fully passivated surfaces and GBs. Ammonium cations with a high acid dissociation constant (pK a ), including PEAMA + (pK a =12.0) and BAMA + (pK a =12.0), can replace PEA + or BA + for passivation and are stable with FA-based perovskites due to their resistance to further deprotonation. P-i-n structure solar cells with PEAMA + additive maintained over 90% of their initial efficiency after light soaking at open circuit and 90 °C for 1500 hours.
14 SOLAR ENERGY↗