Search NASA⌕ Search

Engineering topics

Shimada, M.

Publications and source records attributed to Shimada, M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of rhenium addition on deuterium retention in neutron-irradiated tungsten

In this work, the effects of rhenium (Re) addition on deuterium (D) retention in neutron-irradiated tungsten (W) were investigated. Pure W and W-5Re (5 at.%) alloy samples were irradiated with neutrons at High Flux Isotope Reactor using MFE-RB-19 J capsule. The sample temperature and the damage level were 864 K and 0.35 dpa for pure W and 792 K and 0.26 dpa for W-5Re alloy. A portion of the samples was exposed to D plasma at Tritium Plasma Experiment at Idaho National Laboratory at 823 K to a fluence of 5 × 1025 m -2 . Vacancy-type defects in neutron-irradiated samples were examined using positron annihilation spectroscopy (PAS); D retention after plasma exposure was evaluated by thermal desorption spectrometry (TDS). TDS measurements revealed that D retention in the neutron-irradiated W-5Re alloy was similar to that in the unirradiated W sample, whereas a significant increase in D retention was observed in neutron-irradiated W. Thus, Re addition significantly suppressed the increase in D retention after neutron irradiation. This effect was attributed to the suppression of vacancy-type defect formation, as confirmed by PAS.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

D retention and depth profile behavior for single crystal tungsten with high temperature neutron irradiation

Single crystalline W (tungsten) samples irradiated at 633, 963 and 1073 K by neutrons to a damage level of 0.1 dpa were exposed to a high-flux D (deuterium) plasma at 673, 873 and 973 K, respectively, in TPE (Tritium Plasma Experiment) at INL (Idaho National Laboratory). Deuterium desorption was analyzed by TDS (Thermal Desorption Spectroscopy), and D depth profiles were determined by NRA (Nuclear Reaction Analysis) at SNL (Sandia National Laboratories). HIDT (Hydrogen Isotope Diffusion and Trapping) simulation code was applied to evaluate D behavior for neutron-damaged W at higher temperature. The D retention at depths up to 3 f.tm for the neutron-damaged sample at 673 K was two orders of magnitude larger than that for undamaged tungsten, and its D desorption spectrum had a single broad stage at around 900 K. As the neutron irradiation/plasma exposure temperature increased, D retention was largely reduced, and the desorption temperature was increased to higher temperatures above 1100 K. The D depth profiles by NRA also showed D migration toward bulk by higher temperature irradiation, compared to undamaged W. The HIDT simulation indicated that the major binding energy of D was changed from 1.43 eV to 2.07 eV at higher neutron irradiation and plasma exposure temperatures, suggesting that some vacancies and small vacancy clusters would aggregate to form larger voids, or depopulation of weak traps at high D plasma exposure temperatures. It can be said that more stable trapping sites played dominant roles in the D retention at higher neutron irradiation and plasma exposure temperature. The binding energy by HIDT simulation was almost consistent with the reported value by TMAP, but the consideration of not only total D retention measured by TDS but also D depth profile by NRA led to the more accurate D behavior in neutron-damaged W.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Tritium permeability measurement in hydrogen-tritium system

Fusion power promises to provide electricity generation with outstanding safety and environmental performance. Safety plays a crucial role in fusion material selection since tritium behavior in materials determines two key safety evaluation source terms: in-vessel inventory source term and ex-vessel release term, which are used in reactor safety assessments for licensing fusion facilities. Tritium permeation through materials at elevated temperature during long pulse operation expected in a burning plasma environment will become a major safety issue and development of tritium permeation barrier materials is required to minimize ex-vessel release to the environment [1]. Extensive work on hydrogen and deuterium behavior in fusion materials has been conducted, but very little database is available for tritium, the radioactive fuel for future reactors, due to the cost and difficulty associated with handling tritium [2]. A majority of the experiments were carried out at high hydrogen/deuterium partial pressure (> 100 Pa), but the expected tritium partial pressure in the blanket system is at low tritium partial pressure (< 100 Pa), where the tritium behavior deviates from diffusion-limited to surface-limited permeation. At these pressures the behavior of tritium is suspected to deviate from diffusion-limited to surface-limited permeation or isotope-limited [3]. The use of tritium enables us to investigate hydrogen isotope behavior in low partial pressure range with beta radiation detection. The physics of two-component hydrogen (H+T) permeation through metal in the surface-limited regime and through liquid breeding material are still too poorly understood to confidently design environmentally benign and safe fusion systems. In this paper, we discuss development of tritium permeation system for low tritium partial pressure [4], and discuss the results from two-component hydrogen (H+T) permeation in 20 mm disc samples of pure alpha-iron at H2 partial pressure of 100 Pa, wide T2 partial pressure range from 10-12 to 10 Pa, and sample temperature up to 600 °C to uncover the basic scientific understanding of tritium permeation behavior at realistic blanket conditions for DEMO. [1] FESAC report on “Opportunities for Fusion Materials Science and Technology Research Now and During the ITER Era” (2012) DOE/SC-0149 [2] R.A. Causey, R.A. Karnesky, and C. San Marchi, “4.16 Tritium Barriers and Tritium Diffusion in Fusion Reactors”, Comprehensive Nuclear Materials (2012) Chapter 4.16. [3] P. Humrickhouse “Permeation of Tritium and Hydrogen in the Diffusion-Limited and Surface–Limited Regimes”, submitted to Journal of Nuclear Materials. [4] R.J. Pawelko, M. Shimada, K. Katayama, S. Fukada, P.W. Humrickhouse, and T. Terai, “Low tritium partial pressure permeation system for mass transport measurement in lead lithium eutectic”, Fusion Engineering and Design 102 (2016) 8

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Background studies for the MINER Coherent Neutrino Scattering reactor experiment

The proposed Mitchell Institute Neutrino Experiment at Reactor (MINER) experiment at the Nuclear Science Center at Texas A&M University will search for coherent elastic neutrino-nucleus scattering within close proximity (about 2 m) of a 1 MW TRIGA nuclear reactor core using low threshold, cryogenic germanium and silicon detectors. Given the Standard Model cross section of the scattering process and the proposed experimental proximity to the reactor, as many as 5–20 events/kg/day are expected. In this work, we discuss the status of preliminary measurements to characterize the main backgrounds for the proposed experiment. Both in situ measurements at the experimental site and simulations using the MCNP and GEANT4 codes are described. A strategy for monitoring backgrounds during data taking is briefly discussed.

47 OTHER INSTRUMENTATION↗
DOE OSTI2017

Deuterium retention and blistering in tungsten foils

To investigate deuterium retention and the onset of blistering, deuterium was implanted in cold rolled tungsten foils at fluences ranging from 3x1020 to 3x1022 D/m2. Ion energies were 300 eV and 2000 eV in order to be below and above the tungsten theoretical damage energy threshold. While there were energy dependent phenomena, blistering occurs regardless of ion energy. Both plastically and elastically deformed blisters were observed, as manifest in before and after micrographs. The fraction of plastically deformed blisters did not saturate at the fluences used in these studies. However, the size of the largest blister that relaxes during TDS does saturate at ~7 µm. A simple conceptual model is presented that identifies that deuterium released from elastically deformed blisters appears at ~600 K in the thermal desorption spectra, which is consistent with large vacancy clusters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Tritium Decay Helium-3 Effects in Tungsten

A critical challenge for long-term operation of ITER and beyond to a Demonstration reactor (DEMO) and future fusion reactor will be the development of plasma-facing components (PFCs) that demonstrate erosion resistance to steady-state/transient heat fluxes and intense neutral/ion particle fluxes under the extreme fusion nuclear environment, while at the same time minimizing in-vessel tritium inventories and permeation fluxes into the PFC’s coolant. Tritium will diffuse in bulk tungsten at elevated temperatures, and can be trapped in radiation-induced trap site (up to 1 at. % T/W) in tungsten [1,2]. Tritium decay into helium-3 may also play a major role in microstructural evolution (e.g. helium embrittlement) in tungsten due to relatively low helium-4 production (e.g. He/dpa ratio of 0.4-0.7 appm [3]) in tungsten. Tritium-decay helium-3 effect on tungsten is hardly understood, and its database is very limited. Two tungsten samples (99.99 at. % purity from A.L.M.T. Co., Japan) were exposed to high flux (ion flux of 1.0x1022 m-2s-1 and ion fluence of 1.0x1026 m-2) 0.5%T2/D2 plasma at two different temperatures (200, and 500°C) in Tritium Plasma Experiment (TPE) at Idaho National Laboratory. Tritium implanted samples were stored at ambient temperature in air for more than 3 years to investigate tritium decay helium-3 effect in tungsten. The tritium distributions on plasma-exposed was monitored by a tritium imaging plate technique during storage period [4]. Thermal desorption spectroscopy was performed with a ramp rate of 10°C/min up to 900°C to outgas residual deuterium and tritium but keep helium-3 in tungsten. These helium-3 implanted samples were exposed to deuterium plasma in TPE to investigate helium-3 effect on deuterium behavior in tungsten. The results show that tritium surface concentration in 200°C sample decreased to 30 %, but tritium surface concentration in 500°C sample did not alter over the 3 years storage period, indicating possible tritium retention in helium-3 bubble. This paper reports the initial experimental observation of tritium-decay helium-3 in tungsten exposed to deuterium/tritium plasma along with electron microscope analysis and also discusses a Tritium Migration Analysis Program (TMAP) analysis of tritium-decay helium-3 effects on tritium retention in tungsten for DEMO and future fusion reactor. [1] Y. Hatano, et.al., Nucl. Fusion 53 (2013) 073006 [2] M. Shimada, et.al., Nucl. Fusion 55 (2015) 013008 [3] M. Sawan, Fus. Sci. Technol. 66 (2014) 272 [4] T. Otsuka, Fus. Sci. Technol. 60 (2011) 1539 This work was prepared for the U.S. Department of Energy, Office of Fusion Energy Sciences, under the DOE Idaho Field Office contract number DE-AC07-05ID14517.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Tritium Plasma Experiment Upgrade and Improvement of Surface Diagnostic Capabilities at STAR Facility for Enhancing Tritium and Nuclear PMI Sciences

The Tritium Plasma Experiment (TPE) is a unique high-flux linear plasma device that can handle beryllium, tritium, and neutron-irradiated plasma facing materials, and is the only existing device dedicated to directly study tritium retention and permeation in neutron-irradiated materials with tritium [M. Shimada et.al., Rev. Sci. Instru. 82 (2011) 083503 and and M. Shimada, et.al., Nucl. Fusion 55 (2015) 013008]. The plasma-material-interaction (PMI) determines a boundary condition for diffusing tritium into bulk PFCs, and the tritium PMI is crucial for enhancing fundamental sciences that dictate tritium fuel cycles and safety and are high importance to an FNSF and DEMO. Recently the TPE has undergone major upgrades in its electrical and control systems. New DC power supplies and a new control center enable remote plasma operations from outside of the contamination area for tritium, minimizing the possible exposure risk with tritium and beryllium. We discuss the electrical upgrade, enhanced operational safety, improved plasma performance, and development of optical spectrometer system. This upgrade not only improves operational safety of the worker, but also enhances plasma performance to better simulate extreme plasma-material conditions expected in ITER, Fusion Nuclear Science Facility (FNSF), and Demonstration reactor (DEMO). This work was prepared for the U.S. Department of Energy, Office of Fusion Energy Sciences, under the DOE Idaho Field Office contract number DE-AC07-05ID14517.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

A multi-technique analysis of deuterium trapping and near-surface precipitate growth in plasma-exposed tungsten

In this work, we examine how deuterium becomes trapped in plasma-exposed tungsten and forms near-surface platelet-shaped precipitates. How these bubbles nucleate and grow, as well as the amount of deuterium trapped within, is crucial for interpreting the experimental database. Here, we use a combined experimental/theoretical approach to provide further insight into the underlying physics. With the Tritium Plasma Experiment, we exposed a series of ITER-grade tungsten samples to high flux D plasmas (up to 1.5 × 10{sup 22 }m{sup −2} s{sup −1}) at temperatures ranging between 103 and 554 °C. Retention of deuterium trapped in the bulk, assessed through thermal desorption spectrometry, reached a maximum at 230 °C and diminished rapidly thereafter for T > 300 °C. Post-mortem examination of the surfaces revealed non-uniform growth of bubbles ranging in diameter between 1 and 10 μm over the surface with a clear correlation with grain boundaries. Electron back-scattering diffraction maps over a large area of the surface confirmed this dependence; grains containing bubbles were aligned with a preferred slip vector along the <111> directions. Focused ion beam profiles suggest that these bubbles nucleated as platelets at depths of 200 nm–1 μm beneath the surface and grew as a result of expansion of sub-surface cracks. To estimate the amount of deuterium trapped in these defects relative to other sites within the material, we applied a continuum-scale treatment of hydrogen isotope precipitation. In addition, we propose a straightforward model of near-surface platelet expansion that reproduces bubble sizes consistent with our measurements. For the tungsten microstructure considered here, we find that bubbles would only weakly affect migration of D into the material, perhaps explaining why deep trapping was observed in prior studies with plasma-exposed neutron-irradiated specimens. We foresee no insurmountable issues that would prevent the theoretical framework developed here from being extended to a broader range of systems where precipitation of insoluble gases in ion beam or plasma-exposed metals is of interest.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Conference report on the 3rd International Symposium on Lithium Application for Fusion Devices

The third International Symposium on Lithium Application for Fusion Device (ISLA-2013) was held on 9-11 October 2013 at ENEA Frascati Centre with growing participation and interest from the community working on more general aspect of liquid metal research for fusion energy development. ISLA-2013 has been confirmed to be the largest and the most important meeting dedicated to liquid metal application for the magnetic fusion research. Overall, 45 presentation plus 5 posters were given, representing 28 institutions from 11 countries. The latest experimental results from nine magnetic fusion devices were presented in 16 presentations from NSTX (PPPL, USA), FTU (ENEA, Italy), T-11M (Trinity, RF), T-10 (Kurchatov Institute, RF), TJ-II (CIEMAT, Spain), EAST(ASIPP, China), HT-7 (ASIPP, China), RFX (Padova, Italy), KTM (NNC RK, Kazakhstan). Sessions were devoted to the following: (I) lithium in magnetic confinement experiments (facility overviews), (II) lithium in magnetic confinement experiments (topical issues), (III) special session on liquid lithium technology, (IV) lithium laboratory test stands, (V) Lithium theory/modelling/comments, (VI) innovative lithium applications and (VII) special Session on lithium-safety and lithium handling. There was a wide participation from the fusion technology communities, including IFMIF and TBM communities providing productive exchange with the physics oriented magnetic confinement liquid metal research groups. Furthermore, this international workshop will continue on a biennial basis (alternating with the Plasma-Surface Interactions (PSI) Conference) and the next workshop will be held at CIEMAT, Madrid, Spain, in 2015.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Design of a diagnostic residual gas analyzer for the ITER divertor

One of the ITER diagnostics having reached an advanced design stage is a diagnostic RGA for the divertor, i.e. residual gas analysis system for the ITER divertor, which is intended to sample the divertor pumping duct region during the plasma pulse and to have a response time compatible with plasma particle and impurity lifetimes in the divertor region. Main emphasis is placed on helium (He) concentration in the ducts, as well as the relative concentration between the hydrogen isotopes (H2, D2, T2). Measurement of the concentration of radiative gases, such as neon (Ne) and nitrogen (N2), is also intended. Numerical modeling of the gas flow from the sampled region to the cluster of analysis sensors, through a long (~8m long, ~110mm diameter) sampling pipe terminating in a pressure reducing orifice, confirm that the desired response time (~1s for He or D2) is achieved with the present design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗