Engineering topics

Shin, Swanee J.

Publications and source records attributed to Shin, Swanee J..

6 records

DOE OSTI2024

Deposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects

Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. In this work, we study the deposition of AuTa 4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa 4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Performance scaling with an applied magnetic field in indirect-drive inertial confinement fusion implosions

Magnetizing a cryogenic deuterium–tritium (DT)-layered inertial confinement fusion (ICF) implosion can improve performance by reducing thermal conduction and improving DT-alpha confinement in the hot spot. A room-temperature, magnetized indirect-drive ICF platform at the National Ignition Facility has been developed, using a high-Z, high-resistivity AuTa 4 alloy as the hohlraum wall material. Experiments show a 2.5× increase in deuterium–deuterium (DD) neutron yield and a 0.8-keV increase in hot-spot temperature with the application of a 12-T B-field. Further, for an initial 26-T B-field, we observed a 2.9× yield increase and a 1.1-keV temperature increase, with the inferred burn-averaged B-field in the compressed hot spot estimated to be 7.1 ± 1.8 kT using measured primary DD-n and secondary DT-n neutron yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Ultrathick Boron Carbide Coatings for Nuclear Fusion Targets

Boron carbide is an attractive ablator for next-generation inertial confinement fusion (ICF) targets. Here we describe several aspects of our ongoing systematic studies of the deposition and processing of B 4 C coatings for ICF targets. We show that residual compressive stress in films can be reduced and the deposition rate increased by N-doping. Further, we also demonstrate successful Si substrate etching and surface polishing and discuss remaining challenges and offer potential solutions to the buildup of particulates in the deposition chamber during prolonged coating runs, control of nodular growth defects, and lateral nonuniformity of film properties for deposition conditions with relatively low target-to-substrate distances.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Preparation of Macroscopic Low-Density Gold Foams with Good Machinability

Uniform, macroscopic monoliths (ranging from a few millimeters to a centimeter) of low-density gold foams with ~95% porosity and ~10-μm-diameter pores were prepared by the casting of gold-coated polystyrene core-shell particles followed by the thermal removal of the polymer core. The Au foams were composed of unique hollow gold spheres and showed superior mechanical integrity and resilience compared to the foams we previously reported. Highly efficient seeding and electroless gold-plating methods in this study caused a significant morphological transition in the gold coatings from coarse particles to fine particles, and finally, to a continuous layer. A modified, scalable casting approach to form large uniform monoliths (up to ~1-cm diameter) and a gentle baking condition to minimize undesirable densification of the final foams enabled us to develop a simple, efficient synthetic route to nanostructured macroscopic low-density gold foams. To demonstrate the improved mechanical stability and machinability, a representative monolithic Au foam (~0.9 g/cm 3 ) was carefully cut into the hollow cylinder of gold foams by a series of machining and processing steps. Finally, we tried to understand the unique mechanical behaviors and properties of this gold foam by nanoindentation measurement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Preparation of Mechanically Robust, Macroscopic Low-Density Gold Foams by Highly Efficient Electroless Gold Plating

Mechanically robust, macroscopic-sized low-density gold foams with unique morphology of hollow gold shells were prepared by the synthesis of gold-coated polystyrene coreshell particles followed by thermal removal of the polymer core. Here, we reported a simple, highly efficient electroless gold plating procedure to form ultrathin, conformal gold coatings on the surface of polystyrene particles. A modified, scalable casting approach to form uniform, large monoliths (up to 1 cm diameter) and a baking condition to minimize undesirable densification of final foams were also developed. To demonstrate the mechanical stability and integrity of the Au foams, a representative monolithic sample (~0.9 g/ cm3 ) was successfully cut and shaped into a gold foam “washer” by a series of precision machining and processing. A depth-sensing indentation test (nanoindentation) as well as characterizations on other useful properties such as surface areas and electrical conductivity of the Au foams were carried out to understand the mechanical behavior and potential applicability.

Electroless Gold Plating↗

DOE OSTI2020

Anomalous Anisotropic Nanoparticle Aggregation in Cu 2 (OH) 3 Br Gels

Aerogels are of interest for their ability to uniformly incorporate nanoscale features into macroscopic assemblies, which enabled applications that require low density, high surface area, and/or bicontinuous networks. The structure of the nanoporous network is intrinsically linked to the macroscopic properties of aerogels. Hence, control of this structure is of paramount importance. Small-angle X-ray scattering (SAXS) is used here to monitor nanoparticle aggregation in situ in Cu 2 (OH) 3 Br aerogels formed via epoxide-assisted gelation. Anomalous anisotropic aggregation is observed in the absence of templating agents and is attributed to the molecular structure of the inorganic nanoparticles themselves. This is a fundamental departure from the models currently used to describe traditional inorganic sol–gel chemistry where nanoparticles are believed to undergo isotropic diffusion- and/or kinetically limited aggregation. Time-resolved SAXS indicates that Cu 2 (OH) 3 Br nanoparticles nucleate rapidly from solution to form unbranched chain-like aggregates rather than branched mass-fractal aggregates. Sizes of primary particles (~1.5 nm) and the chain-like structure of their aggregates are independent of particle concentration (gel density), while rates of particle aggregation, gelation time, and aggregate size are strongly dependent upon particle concentration, which implies that the chemistry of particle formation and the physics of particle aggregation are independent processes. Because the conditions necessary for creating anisotropic structures are not unique to Cu 2 (OH) 3 Br, these results could provide insight into the structure and gelation mechanisms of other inorganic aerogels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗