WALL HEATING BY SUBCRITICAL ENERGETICELECTRONS GENERATED BY THE RUNAWAYELECTRON AVALANCHE SOURCE
Explore the source record for details and available documents.
Beidler, Matthew↗
Engineering topics
Shiraki, Daisuke
Publications and source records attributed to Shiraki, Daisuke.
Reducing the L-H transition power threshold in ITER-similar-shape DIII-D hydrogen plasmas
Recent dedicated DIII-D experiments in low-torque, ITER-similar-shape (ISS) hydrogen plasmas (at a plasma current I p ~ 1.5 MA and ITER-similar edge safety factor q 95 ~ 3.6) show that the L-H transition power threshold P LH can be reduced substantially (~30%) with L-mode helium admixtures n He /n e $\leqslant$ 25%. In the ensuing H-mode, helium ion fractions n He /n H remain below 25%. H-mode normalized pressure and confinement quality are only slightly affected by helium seeding, and Z eff $\leqslant$ 2.15 (including helium and carbon content). The plasmas investigated here are electron-heat dominated, with temperatures T e (0)/T i (0) $\geqslant$ 1 and edge heat flux ratio Q e /Q i (ρ = 0.95) ~ 1.2–1.5. Without mitigation, P LH is higher by a factor of 2–3 in comparison to similar ISS deuterium plasmas. ISS hydrogen plasmas with lower plasma current I p ~ 1 MA (increased edge safety factor q 95 ~ 5.1) exhibit a substantially lower power threshold. This plasma current dependence, also observed previously on ASDEX-U and in JET, is not accounted for by the commonly used 2008 ITPA multi-machine threshold scaling, but could potentially allow H-mode access at marginal heating power during the initial plasma current ramp-up. Attempts to reduce P LH with low-field- and high-field-side hydrogen pellet injection, using 1.7 mm diameter pellets, have not demonstrated a robust threshold reduction, in contrast to successful earlier experiments with larger 2.7 mm pellets. Finally, techniques for reducing P LH are very important for ITER, in particular for accessing H-mode in hydrogen plasmas during the Pre-Fusion Power Operation-1 (PFPO-1) campaign with marginal auxiliary heating power (20–30 MW of ECH).
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Pellet triggering of edge localized modes in low collisionality pedestals at DIII-D
Edge localized modes (ELMs) are triggered using deuterium pellets injected into plasmas with ITER-relevant low collisionality pedestals, and the resulting peak ELM energy fluence is reduced by approximately 25%–50% relative to natural ELMs destabilized at similar pedestal pressures. Cryogenically frozen deuterium pellets are injected from the low-field side of the DIII-D tokamak at frequencies lower than the natural ELM frequency, and heat flux is measured by infrared cameras. Ideal MHD pedestal stability calculations show that without pellet injection, these low collisionality pedestals were limited by their current density (peeling-limited) rather than their pressure gradient (ballooning-limited). ELM triggering success correlates strongly with pellet mass, consistent with the theory that a large pressure perturbation is required to trigger an ELM in low collisionality discharges that are far from the ballooning stability boundary. For sufficiently large pellets, both instantaneous and time-integrated ELM energy deposition measured by infrared cameras is reduced with respect to naturally occurring ELMs at the inner strike point, which is the position where it is largest for natural ELMs. Energy fluence at the outer strike point is less effected. Cameras observing both heat flux and D-alpha emission often find significant toroidally asymmetric striations in the outboard far scrape-off layer resulting from ELMs that are triggered by pellets. Toroidal asymmetries at the inner strike point are similar between natural and pellet-triggered ELMs, indicating that the reduction in peak heat flux and total fluence at that location is robust for the conditions reported here.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Pellet ELM triggering in DIII-D with low collisionality, peeling-limited pedestals
Explore the source record for details and available documents.
Wilcox, Robert↗
A novel path to runaway electron mitigation via deuterium injection and current-driven MHD instability
Relativistic electron (RE) beams at high current density (low safety factor, qa) yet very low free-electron density accessed with D2 secondary injection in the DIII-D and JET tokamak are found to exhibit large-scale MHD instabilities that benignly terminate the RE beam. In JET, this technique has enabled termination of MA-level RE currents without measurable first-wall heating. This scenario thus offers an unexpected alternate pathway to achieve RE mitigation without collisional dissipation. Benign termination is explained by two synergistic effects. First, during the MHD-driven RE loss events both experiment and MHD orbit-loss modeling supports a significant increase in the wetted area of the RE loss. Second, as previously identified at JET and DIII-D, the fast kink loss timescale precludes RE beam regeneration and the resulting dangerous conversion of magnetic to RE kinetic energy. During the termination, the RE kinetic energy is lost to the wall, but the current fully transfers to the cold bulk thus enabling benign Ohmic dissipation of the magnetic energy on longer timescales via a conventional current quench. Hydrogenic (D2) secondary injection is found to be the only injected species that enables access to the benign termination. D2 injection: 1) facilitates access to low qa in existing devices (via reduced collisionality & resistivity), 2) minimizes the RE avalanche by ‘purging’ the high-Z atoms from the RE beam, 3) drives recombination of the background plasma, reducing the density and Alfven time, thus accelerating the MHD growth. Furthermore, this phenomenon is found to be accessible when crossing the low qa stability boundary with rising current, falling toroidal field, or contracting minor radius - the latter being the expected scenario for vertically unstable RE beams in ITER. While unexpected, this path scales favorably to fusion-grade tokamaks and offers a novel RE mitigation scenario in principle accessible with the day-one disruption mitigation system (DMS) of ITER.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Polarized imaging of visible synchrotron emission from runaway electron plateaus in DIII-D
A new approach to estimate the pitch angle of highly energetic postdisruption runaway electrons is presented by imaging the polarized runaway electron synchrotron emission. The vertical to horizontal polarization ratio is found to range between 3 and 14 in image-average studies looking at repeated shots as well as the polarization in a single discharge. Numerical studies with guiding center and full orbit simulations performed with the SOFT and KORC codes are given and compared to the experiment. The pitch angle evolution analyzed using a 1D impurity diffusion model in combination with kinetic simulations is also presented. Furthermore, these studies find agreement in the magnitude of the pitch angle, but not in the temporal rate of change of pitch angle. The measured pitch angle evolution timescale of order 50 ms falls between a modeled timescale of 20 ms in an equilibrium model and >>100 ms in a nonequilibrium model.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
3D radiation, density, and MHD structures following neon shattered pellet injection into stable DIII-D Super H-mode discharges
Six nominally repeat neon shattered pellet injection (SPI) shutdowns of stable DIII-D Super H-modes are studied to understand the 3D properties of the radiation and impurity transport. The radiation efficiency and radiation peaking determine whether first wall melting is expected following disruption mitigation in ITER. Previous studies make use of axisymmetric approximations to infer radiation efficiencies, but validating the high efficiency required by ITER necessitates improved accuracy, and this work contributes by exploring the 3D radiation and density structures that will inform forward modeling. When the neon shatter plume produced by the SPI reaches the plasma edge, m/n = 3/1 and 2/1 island O-points are observed to align with the injection trajectory in five out of six cases, suggesting that the injected material seeds the island O-points. Field aligned neon structures emitting Ne-I line radiation drift at 1 km/s in the ion diamagnetic drift direction during the pre-TQ, tracking the motion of the m/n = 2/1 island O-point. Neon fragments penetrate to the q = 2 surface by the time of the TQ. Techniques to constrain the 3D emissivity are explored, and one method constrains a 3D flux tube that is consistent with the radiation data, and when mapped to the interferometers, intersects the lasers that measure the highest density. The resulting structure derived from the radiation measurements exists near the 2/1 island X-point. In five repeatable discharges, the peak of the radiation in the toroidal direction exists in a 120° toroidal sector where the injection occurs, in contrast with the outlier discharge where the toroidal peak exists in the complementary 240° toroidal sector far from the injector, and where a 50% lower density rise is observed. In conclusion, the n = 1 phase behavior is markedly different in the outlier discharge, suggesting a possible dependence of the radiation structure and the assimilation efficiency on MHD.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Spatially dependent modeling and simulation of runaway electron mitigation in DIII-D
New simulations with the Kinetic Orbit Runaway electron (RE) Code (KORC) show RE deconfinement losses to the wall during plasma scrape off are the primary current dissipation mechanism in DIII-D experiments with high-Z impurity injection, and not collisional slowing down. The majority of simulations also exhibit an increase in the RE beam energy due to acceleration by the induced toroidal electric field, even while the RE beam current is decreasing. In this study, KORC integrates RE orbits using the relativistic guiding center equations of motion and incorporates time-sequenced, experimental reconstructions of the magnetic and electric fields and line integrated electron density to construct spatiotemporal models of electron and partially ionized impurity transport in the companion plasma. Comparisons of experimental current evolution and KORC results demonstrate the importance of including Coulomb collisions with partially ionized impurity physics, initial RE energy, pitch angle, and spatial distributions, and spatiotemporal electron and partially ionized impurity transport. The research presented here provides an initial quantification of the efficacy of RE mitigation via injected impurities and identification of the critical role played by loss of confinement due to plasma scrape off on the inner wall as compared to the relatively slow collisional damping.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Runaway electron beam dynamics at low plasma density in DIII-D: energy distribution, current profile, and internal instability
Parameters of the post-disruption runaway electron (RE) beam in the collisionless background plasma achieved after deuterium injection are investigated in DIII-D. The spatially resolved RE energy distribution function is measured for the first time during the RE plateau stage by inverting hard X-ray bremsstrahlung spectra. It has maximum energy up to 20 MeV and a non-monotonous feature at 5{6 MeV observed only in the core of the beam supporting the possibility of kinetic instabilities. The RE current profile is reconstructed for the first time using the spatially resolved RE energy distribution. It is found to be more peaked than the pre-disruption plasma current, with higher internal inductance, suggesting preferential formation of REs in the core plasma or potentially a radially inward motion of the REs. The accessed relatively low-current (180 kA) RE beam is found stable, likely due to its elevated q profile. From this base stable equilibrium, instability is accessed by ramping the solenoid current. Under a large applied accelerating loop voltage an internal kink mode is observed. The kink mode leads to sawtooth-like relaxation of the RE current profile, but drives no RE loss. Under conditions of a large decelerating voltage, chirping Alfvénic instabilities driven by REs during the RE plateau stage are observed for the first time. The low-frequency (0.1{7 MHz) Alfvénic instabilities, supposedly compressional Alfvén eigenmodes, are found to be correlated with a RE loss signal. Finally, this provides novel plasma conditions to study these instabilities and investigate opportunities to utilize them for RE control. Bifurcated electron cyclotron emission (ECE) spectrum is measured during the collisionless RE plateau, with a break point at ≈100 GHz suggesting resonant absorption of the ECE at low frequencies.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Setting the H-mode pedestal structure: variations of particle source location using gas puff and pellet fueling
Experiments in DIII-D show that a particle source location inside the top of the H-mode pedestal (pellets) maintains a higher pedestal pressure than an edge source (gas fueling) through a widening of the electron temperature pedestal with reduction of the temperature gradient. The effect of these two fueling schemes on the H-mode pedestal structure was examined in DIII-D by comparing controlled pellet-fueled and gas-fueled discharges across a fueling scan up to 40 torr 1 s –1 . High resolution electron profiles reveal that gas fueling lowers the pedestal pressure as the density profile shifts radially outwards and the separatrix density increases, while pellet fueling maintains a constant pedestal pressure. The neutral source locations from pellets and gas are determined with the PELLET and UEDGE codes, respectively, and quantify the particle source localization. Pellets provide significant ionization inside the pedestal top while gas puffing localizes ionization in the scrape-off-layer and pedestal foot, broadly consistent with the density profile structure influenced by the source. ELMs are observed to increase in frequency and reduce impurity content as fueling is increased. Stability analysis with ELITE shows that both conditions are near the type-I ELM corner of the peeling–ballooning stability diagram, which is altered significantly by the introduction of pellets. Since transport mechanisms are not observed to change substantially with particle source location, wider pedestals allow the pellet-fueled discharges to retain higher pedestal temperatures at similar pedestal densities. EPED1 is tested to capture the pedestal pressure, under-predicting the height with pellets and over-predicting the height with gas by ~15%. Overall, these results have important implications for future reactors where pellet fueling will be the primary particle source due to an opaque scrape-off-layer by showing that the neutral source location plays a role in setting the structure of the H-mode pedestal.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Shattered pellet penetration in low and high energy plasmas on DIII-D
Shattered Pellet Injection (SPI) was previously adopted as the baseline disruption mitigation system for ITER, as the radiative payload penetration into DIII-D plasmas from SPI is superior to those using the Massive Gas Injection (MGI) method. Because of the substantial differences in the energy content of ITER plasma and those in present experiments, reliable 3d MHD modeling, benchmarked against present experiments is needed to project to ITER plasmas. On account of these needs, the depth of SPI fragment penetration in DIII-D plasmas was investigated by injecting SPI into two discharges with vastly different energy content and pedestal height. 400 Torr-L pure Ne fragmented pellets at a velocity of about 200 m s -1 were injected into a 0.2 MJ L-mode discharge and a 2 MJ super H-mode discharge. Results show deep penetration of SPI fragments into low-energy plasmas in DIII-D. SPI fragment penetration is reduced as the plasma energy content increases, with some discharges exhibiting penetration that is confined to the outer regions of the plasma. The injected SPI fragments are also spread out over a distance of about 20 cm, which results in some fragments arriving near the end of or after the thermal quench is over.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗