Search NASA⌕ Search

Engineering topics

Shmayda, W T

Publications and source records attributed to Shmayda, W T.

Atomic mix in directly driven inertial confinement implosions

Directly driven implosions on the Omega laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have measured the presence of atomic mix using D+T neutron yield rates from plastic capsules with and without deuterated layers, and a nearly pure tritium fuel containing 0.7% deuterium. In 15, 19, and 24 {mu}m thick plastic shells, D+T neutron yields increased by factors of 86, 112, and 24 when the 1.2 {mu}m thick inner layer was deuterated. Based on adjusting a fully atomic mix modvfel to fit yield degradation in the un-deuterated capsule and applying it to the capsule with the deuterated layer, atomic mixing accounts for 40-75% of the yield degradation due to mix. For the first time, the time dependence of mixed mass was measured by the ratio of the yield rates from both types of capsules. As expected, the amount of mix grows throughout the D+T burn.

36 MATERIALS SCIENCE↗

Effects of H2O and H2O2 on Thermal Desorption of Tritium from Stainless Steel

Tritiated stainless steel was subjected to thermal desorption at various temperatures, different temperature profiles, and in the presence of different helium carrier gas additives. In all cases the identities of the desorbing tritiated species were characterized as either water-soluble or insoluble. The samples were found to contain 1.1 mCi±0.4 mCi. Approximately ninety-five percent of this activity was released in molecular water-soluble form. Additives of H2O or H2O2 to dry helium carrier gas increase the desorption rate and lower the maximum temperature to which the sample must be heated, in order to remove the bulk of the tritium. The measurements validate a method of decontamination of tritiated steel and suggest a technique that can be used to further explore the mechanisms of desorption from tritiated metals.

Quinlan, M J↗

Cryogenic Target-Implosion Experiments on OMEGA

The University of Rochester’s Laboratory for Laser Energetics has been imploding thick cryogenic targets for six years. Improvements in the Cryogenic Target Handling System and the ability to accurately design laser pulse shapes that properly time shocks and minimize electron preheat, produced high fuel areal densities in deuterium cryogenic targets (202+/-7 mg/cm^2). The areal density was inferred from the energy loss of secondary protons in the fuel (D2) shell. Targets were driven on a low final adiabat (alpha = 2) employing techniques to radially grade the adiabat (the highest adiabat at the ablation surface). The ice layer meets the target-design toughness specification for DT ice of 1-um rms (all modes), while D2 ice layers average 3.0-um-rms roughness. The implosion experiments and the improvements in the quality and understanding of cryogenic targets are presented.

Harding, D R↗

LLE's High-Pressure DT-Fill Process Control System

The OMEGA Laser at the University of Rochester's Laboratory for Laser Energetics (UR/LLE) implodes fusion targets that contain cryogenic solid deuterium-tritium (DT) ice layers. These ICF targets are fabricated in a high-pressure DT-fill process. This paper describes the integration and control of this DT-fill process. The appropriate safety-control response during the DT-fill process depends on the location of the tritium inventory and where the containment alarm is detected. A control response that is deemed appropriate earlier in the fill process could be a dangerous action at a later point in the fill process. The control system must adapt as the DT inventory moves through the process train. This is achieved by defining eight "fill states" in the fill process. The control system transitions to the appropriate fill state as the DT fill progesses. The fill state reflects the tritium location, pressure, and temperature. Steps are taken to ensure that the tritium location and the fill state are in agreement. The control system monitors the containment system's integrity and will take the appropriate action, based on the tritium location and the type of containment failure. This approach not only ensures process safety, but also maximizes the productivity by executing process pauses (in lieu of aborts) when conditions allow.

Duffy, T↗