Search NASA⌕ Search

Engineering topics

Shukla, Shivakant

Publications and source records attributed to Shukla, Shivakant.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗
DOE OSTI2024

A comparative analysis of residual stresses from friction stir processing of aluminum cast 380 and wrought 7075 alloy sheets: experimental characterization and modeling

Residual stresses are often overlooked in friction stir processing (FSP), but their significant impact on fatigue performance necessitates their consideration in optimizing processing parameters. The first step in this effort is understanding how process conditions influence residual stress distributions, especially across different alloys. This study focuses on determining and explaining the through-thickness residual stress variations and the effect of process temperature on the residual stress magnitude in wrought AA7075 and cast AA380.0 alloys. Additionally, for AA380.0, the impact of a second FSP pass was investigated. To achieve this, hole-drilling electronic speckle pattern interferometry (ESPI) and the thermal pseudo-mechanical (TPM) model within finite element analysis were employed to study the 3D distributions of in-plane residual stresses in processed samples under various conditions. A key finding was the varying impact of process temperatures on residual stress magnitudes. Higher process temperatures reduced stresses in AA380.0 but increased them in AA7075. Additionally, the through-thickness stress distributions differed between the two alloys. Further analysis revealed that yield stresses are crucial in explaining these phenomena and the effects of additional FSP passes. Further, this fundamental understanding will be vital in guiding the efforts to mitigate residual stresses and assess their impact on the performance of FSP aluminum alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cast Components for High Temperature Concentrated Solar Power Thermal Systems

Concentrating Solar-Thermal Power (CSP) components such as piping, valves fittings are required for use at temperatures up to 800°C. These are anticipated to be made using Nickel-based alloys such as Haynes ® 230 ® , Haynes ® 282 ® , or IN ® 740H ® and can contribute significantly to the cost of a CSP Gen 3 plant. Thus, there is a significant motivation to lower the cost of materials and components so that the capital costs can be minimized. In all these cases, the cost of the component has two contributions: 1. Materials cost, and 2. Manufacturing cost. Both materials cost and manufacturing costs must be kept low to attain the lowest possible cost. Materials cost can be lowered by using materials that have the ideal combination of properties at the lowest cost. Another avenue to lower cost is chose a manufacturing process that has the potential to lower the cost. Traditionally tubes are made from billets through a wrought process and can be expensive. An alternative process to consider is the centrifugal casting process where the tube is directly fabricated from molten metal. In this case, the molten metal is poured inside a cylindrical metallic mold with an insulating layer and is spun rapidly. A wide range of sizes (diameter, wall thickness, and length) can be cast using this process. The objective of this project was to develop the process for fabricating pipes and related components using a centrifugal casting process and to measure the properties of alloys fabricated using this process.

14 SOLAR ENERGY↗
DOE OSTI2022

Development of Cast Valve Bodies For High Temperature Service

Gen 3 Concentrating Solar-Thermal Power (CSP) system components are required to operate at 750°C - 800°C to achieve the Sunshot target of 6 cents/kWh. Haynes ® 282 and IN ® 740H are preferred alloys for the construction of these components due to their high tensile and creep strengths for service at temperatures greater than 750°C. There is significant motivation to lower the cost of materials and components so that the capital costs can be minimized. One approach to reduce costs is to fabricate castings at the lowest possible cost. To obtain the lowest cost in castings, there is a significant need to maximize yields in castings by decreasing rejects due to casting defects and to minimize wastage in material lost in the gating systems. However, very little work has been performed to develop cast products using Haynes ® 282. Although preliminary work has established the feasibility of casting Haynes ® 282 using investment and sand casting, there are no commercial cast components available. In particular, there is significant interest in the development of casting design and process technology for the fabrication of components such as valve bodies using Haynes ® 282.

14 SOLAR ENERGY↗
DOE OSTI2021

Understanding the microstructural stability in a y’-strengthened Ni-Fe-Cr-Al-Ti alloy

Ni-Fe-Cr-Al-Ti alloys, with Ni levels near 50 wt.%, have the potential to develop a microstructure consisting of a face-centered cubic ? matrix with the homogeneous precipitation of fine ordered ?’ precipitates similar to traditional Ni-based superalloys with significantly greater Ni content. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), atom probe tomography (APT), and CALPHAD -based thermodynamic modeling were employed to understand the phase stabilities and microstructural evolution in an age-hardenable Ni-27Fe-18Cr-1Co-1.6Al-3.75Ti-1.2Mo-0.03C (wt%) alloy. The primary heat-treatment of solution annealing at 1121°C for 4h and age-hardening treatment at 760 °C for 16h resulted in a microstructure consisting of fine ?’ precipitates in an austenitic matrix along with grain boundary carbides, consistent with thermodynamic calculations. Long-term aging at 900 °C for 250h resulted in the coarsening of ?’ along with a change in the morphology of the precipitates from spherical to a more cuboidal shape. In addition, ? phase formation was observed concomitant with the partial dissolution of the ?’ phase. The ability of computational thermodynamic models to predict microstructural characteristics is discussed.

Gwalani, Bharat↗
DOE OSTI2021

High Density of Strong yet Deformable Intermetallic Nanorods Leads to an Excellent Room Temperature Strength-Ductility Combination in a High Entropy Alloy

This paper introduces a new microstructural template for high entropy alloys (HEAs), where the face centered cubic (FCC) complex concentrated solid solution is reinforced with a high density of strong, yet deformable, nanorods of an ordered multi-component intermetallic L12 compound. Thermodynamic modeling has been employed to design this HEA with a large L12 volume fraction. Thermo-mechanical processing by isothermal annealing of the conventionally processed bulk cold-rolled alloy directly at precipitation temperatures, has been applied to produce a high density of uniformly distributed L12 nanorods within refined FCC grains, resulting from concomitant recrystallization and discontinuous precipitation processes. The nanorod morphology of the discontinuous L12 product has been established from three-dimensional atom probe tomography. The refined grains result in a complete coverage of the microstructure with discontinuously precipitated intermetallic nanorods. This nanorod strengthened HEA exhibits an exceptionally high room temperature yield strength of ~1630 MPa, good tensile ductility of ~15%, and an ultimate tensile strength of ~1720 MPa. Furthermore, a single L12 phase alloy, melted based on the precipitate composition in the two-phase FCC + L12 HEA, exhibits very high compressive deformability and strain hardenability, unusual for ordered intermetallic compounds. These results open a new strategy for design of fine-grained microstructures strengthened via ordered intermetallic phases, exploiting the beneficial effects of discontinuous precipitation, for achieving very high room temperature tensile strengths while maintaining good ductility.

Gwalani, Bharat↗
DOE OSTI2021

Design of heterogeneous structured Al alloys with wide processing window for laser-powder bed fusion additive manufacturing

Required microstructural attributes of an alloy vary with structural applications. The microstructural fine-tuning capability of laser-powder bed fusion (L-PBF) additive manufacturing (AM) enables application specific manufacture of the components. Such manufacture with L-PBF AM requires alloys that exhibit wide processing window and are amenable to multiple deformation mechanisms. However, high hot cracking susceptibility of Al alloys poses a barrier to such printability-performance synergy. In this work we show that an integration of, a) grain refinement through heterogeneous nucleation, and b) eutectic solidification, leads to crack-free parts at wide range of process parameters, microstructural heterogeneity, and hierarchy in the Al-Ni-Ti-Zr alloy. Such an integration targets hot cracking at multiple stages of solidification in L-PBF as opposed to the contemporary alloy design strategies that target hot-cracking at only specific stages of solidification. The Al-Ni-Ti-Zr alloy exhibits excellent printability and a high as-built tensile performance. Due to the wide processing window and amenability to multiple deformation mechanisms, the alloy microstructure and subsequently the performance, can be fine-tuned. Here, such strategy opens the gateway for application-specific manufacture of Al alloys with L-PBF AM and establishes a fundamental shift in current methodologies for design of these alloys for L-PBF AM.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Friction stir gradient alloying: A high-throughput method to explore the influence of V in enabling HCP to BCC transformation in a γ-FCC dominated high entropy alloy

The compositional possibilities in high entropy alloys (HEAs) is very vast and effective strategies are needed to establish potential alloy chemistries. In this study, friction stir gradient alloying (FSGA), a recently-introduced high-throughput (HT) technique incorporating compositional and microstructural gradients, was used to explore the possibility of introducing a bcc transformation domain in γ-fcc dominated TRIP HEA Fe 38.5 Mn 20 Cr 15 Co 20 Si 5 Cu 1.5 (at.%) by vanadium addition. FSGA has accelerated the process of attaining the composition-microstructure library and the results suggest that vanadium addition of ~1 at.% results in nucleation of α-bcc. Additionally, this is the first observation of ε-hcp to α-bcc transformation in a TRIP HEA and supports the Olson-Cohen model of martensitic transformation (γ-fcc → ε-hcp → α-bcc). ε-hcp is nucleated with a pyramidal orientation by the formation of planar faults on the {111} close-packed planes of γ-fcc, and α-bcc is nucleated in the vicinity of ε-hcp along the {111} γ-fcc trace. There are indications for the formation of basal orientated ε-hcp from intersecting ε-hcp planes orientated for the pyramidal slip. Thus, the study shows the nucleation and growth of the α-bcc phase attributed to the dual effects of chemistry and strain and potential co-existence of all the three phases.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additively manufactured novel Al-Cu-Sc-Zr alloy: Microstructure and mechanical properties

An in-depth understanding of microstructure and resultant properties is paramount in the design of a novel alloy system, especially for additive manufacturing (AM). The present investigation aims to characterize a prototypical AM Al alloy with great potential for structural applications. An Al-1.5Cu-0.8Sc-0.4Zr alloy designed using integrated computational material engineering was printed using the laser powder bed fusion AM process. This novel alloy shows promising combination of strength and ductility in as-built and peak-aged conditions. This improvement in the tensile properties is attributed to the presence of both coherent L1 2 Al 3 Sc/Al 3 (Sc,Zr) precipitates and Cu-rich regions. The microstructures were studied via extensive microscopy at different length scales using X-ray microscopy, scanning electron microscopy, and transmission electron microscopy. Fractography revealed that the columnar grain boundaries in as-built condition allow easy slip transfer as compared to the equiaxed grains, with the apex of the melt pool acting as the crack nucleation site. Furthermore, the peak aged condition resulted in improved strength while marginally sacrificing ductility due to precipitates decorating dislocations, grain boundaries and melt pool boundaries thus acting as obstacles to slip transfer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure–Property Correlation in a Laser Powder Bed Fusion Processed High-Strength AF-9628 Steel

Laser powder bed fusion additive manufacturing (LPBF-AM) of a low-alloy, high-performance AF-9628 steel results in exceptionally high strength and good ductility. The reasons for such mechanical properties are investigated through detailed microscopy performed at several length scales. Thus, the characterization of melt pool, porosity, grain morphology, phases, and dislocations is performed in the as-printed material. The as-printed material consists of only 0.004 vol% of uniformly distributed porosity, single-phase martensitic laths with an average lath size of ≈2.5 μm, the absence of carbides indicating interstitial trapping of C atom, and high dislocation density in the martensitic laths. Experimental data through microscopy are then fed in analytical models for calculating strengthening contributions from various strengthening mechanisms. Calculated yield strength agrees well with experimentally determined value, and therefore, activation of various strengthening mechanisms is established in as-printed AF-9628.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Excellent high cyclic fatigue properties of a novel ultrafine-grained medium entropy alloy

Fatigue is a major cause of failure and requires dedicated investigation to validate the integrity of potential structural materials. As high and medium entropy alloys (HEAs and MEAs) are garnering significant attention from scientific communities, it is important to test the structural integrity of these novel alloys in cyclic loading environment. This study analyzed both monotonic and cyclic loading properties of a novel medium entropy alloy (MEA) CoCr 1.3 Ni in the ultrafine-grained (UFG) and fine grain (FG) conditions. The UFG MEA performs better than the FG MEA during cyclic loading. Microstructural evolution after cyclic loading via electron back-scattered diffraction shows microstructural stability of both FG and UFG microstructures. Transmission electron microscopy suggests formation of stacking faults and fine-scale HCP transformation during cyclic loading.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Notch-tensile behavior of Al0.1CrFeCoNi high entropy alloy

Notch-tensile behavior of an Al0.1CrFeCoNi high entropy alloy (Al0.1-HEA) was studied using V-notch geometry and with local strain mapping using digital image correlation (DIC). A notch-strength ratio of 1.51 indicated notch strengthening. Further analysis of stress-strain response supplemented with microstructural analysis revealed that, while the presence of notch results in strengthening due to work hardening by twinning induced plasticity, the notch also contributes strongly to geometrical softening in the non-uniform ductility regime, and accounts for the onset of failure. The strain localization behavior of Al0.1-HEA due to the presence of V-notch was compared with three conventional alloys: Inconel 625 nickel-based superalloy, 304 stainless steel and Ti–6Al–4V titanium alloy. The study revealed that the nature of notch widening with increasing strain was dependent on material characteristics. The extent of notch widening impacted the local strain field and stress distribution, thereby influencing the propensity for crack initiation and growth. The experimental results were verified by finite element analysis.

Sinha, Subhasis↗