Search NASA⌕ Search

Engineering topics

Shutthanandan, V

Publications and source records attributed to Shutthanandan, V.

At least 19 records

Perovskite Sr-doped LaCrO3 as a new p-type transparent conducting oxide

Transparent conducting oxides (TCOs) constitute a unique class of materials which combine the seemingly mutually exclusive properties of electrical conductivity and optical transparency in a single material. TCOs are useful for a wide range of applications including solar cells, displays, light emitting diodes and transparent electronics. Simple post-transition metal oxides such as ZnO, In2O3 and SnO2 are wide gap insulators in which the ionic character generates an oxygen 2p-derived valence band (VB) and a metal s-derived conduction band (CB), resulting in large optical band gaps (>3.0 eV) and excellent n-type conductivity when donor doped. In contrast, the development of efficient p-type TCOs remains a global materials challenge. Converting n-type oxides to p-type analogs by acceptor doping is extremely difficult and these materials display poor conductivity.

complex oxide↗

Structure And Radiation Damage Behavior Of Epitaxial CrxMo1-x Alloy Thin Films On MgO

Phenomena related to the interaction of point defects and dopants with grain boundaries and interfaces have been very well documented. However, a quantitative understanding of such an interaction is still missing. In this paper we explore the correlation between radiation damage and interface structure. In doing so, CrxMo1-x(001) films of thickness ~100 nm were epitaxially grown on MgO (001) using molecular beam epitaxy. The interface dislocation density can be systematically varied by controlling the composition of the film. This system allows us to probe the response of the defects generated during the irradiation to the interface dislocation density. The microstructural features of these films before and after irradiation are carefully studied using high resolution scanning/transmission electron microscopy and electron diffraction. It has been found that the film/substrate system is very resistant to ion-induced irradiation damage. No visible point defect clusters, dislocation network or amorphization has been identified, which is contrasted with other materials of either metallic or ionic bonding. We conclude that the defects in the present system appear to be either sub-microscopic and highly dispersed or are annihilated during the irradiation process. Further detailed work is needed to identify the spatial distribution of the defects.

Environmental Molecular Sciences Laboratory↗

A Model for Phosphosilicate Glass Deposition via POCl3 for Control of Phosphorus Dose in Si

Effective control of diffused phosphorus profiles in crystalline silicon requires detailed understanding of the doping process. We develop a model and analyze concentration profiles within the deposited phosphosilicate glass (PSG) for a range of POCl3 conditions. During predeposition, a PSG layer with composition nearly independent of process conditions forms. This layer is separated from Si by a thin SiO2 layer. There is also strong accumulation of P at the SiO2-Si interface. A simple linear-parabolic model cannot fully explain the kinetics of thickness and dose; while an improved model including oxygen dependence and dose saturation gives better fits to the experiments.

Control↗

Performance of solid oxide fuel cells operated with coal syngas provided directly from a gasification process

Solid oxide fuel cells (SOFCs) are presently being developed for gasification integrated power plants that generate electricity from coal at 50+% efficiency. The interaction of trace metals in coal syngas with the Ni-based SOFC anodes is being investigated through thermodynamic analyses and in laboratory experiments, but direct test data from coal syngas exposure are sparsely available. This research effort evaluates the significance of SOFC performance losses associated with exposure of a SOFC anode to direct coal syngas. SOFC specimen of industrially relevant composition are operated in a unique mobile test skid that was deployed to the research gasifier at the National Carbon Capture Center (NCCC) in Wilsonville, AL. The mobile test skid interfaces with a gasifier slipstream to deliver hot syngas (up to 300°C) directly to a parallel array of 12 button cell specimen, each of which possesses an active area of approximately 2 cm2. During the 500 hour test period, all twelve cells were monitored for performance at four discrete operating current densities, and all cells maintained contact with a data acquisition system. Of these twelve, nine demonstrated good performance throughout the test, while three of the cells were partially compromised. Degradation associated with the properly functioning cells was attributed to syngas exposure and trace material attack on the anode structure that was accelerated at increasing current densities. Cells that were operated at 0 and 125 mA/cm² degraded at 9.1 and 10.7% per 1000 hours, respectively, while cells operated at 250 and 375 mA/cm² degraded at 18.9 and 16.2% per 1000 hours, respectively. Post-trial spectroscopic analysis of the anodes showed carbon, sulfur, and phosphorus deposits; no secondary Ni-metal phases were found.

Environmental Molecular Sciences Laboratory↗

Feasibility of the detection of trace elements in particulate matter using online High-Resolution Aerosol Mass Spectrometry

The feasibility of using an online thermal-desorption electron-ionization high-resolution aerosol mass spectrometer (AMS) for the detection of particulate trace elements was investigated analyzing data from Mexico City obtained during the MILAGRO 2006 field campaign, where relatively high concentrations of trace elements have been reported. This potential application is of interest due to the real-time data provided by the AMS, its high sensitivity and time resolution, and the widespread availability and use of this instrument. High resolution mass spectral analysis, isotopic ratios, and ratios of different ions containing the same elements are used to constrain the chemical identity of the measured ions. The detection of Cu, Zn, As, Se, Sn, and Sb is reported. There was no convincing evidence for the detection of other trace elements commonly reported in PM. The elements detected tend to be those with lower melting and boiling points, as expected given the use of a vaporizer at 600oC in this instrument. Operation of the AMS vaporizer at higher temperatures is likely to improve trace element detection. The detection limit is estimated at approximately 0.3 ng m-3 for 5-min of data averaging. Concentration time series obtained from the AMS data were compared to concentration records determined from offline analysis of particle samples from the same times and locations by ICP (PM2.5) and PIXE (PM1.1 and PM0.3). The degree of correlation and agreement between the three instruments (AMS, ICP, and PIXE) varied depending on the element. The AMS shows promise for real-time detection of some trace elements, although additional work including laboratory calibrations with different chemical forms of these elements are needed to further develop this technique and to understand the differences with the ambient data from the other techniques. The trace elements peaked in the morning as expected for primary sources, and the many detected plumes suggest the presence of multiple point sources, probably industrial, in Mexico City which are variable in time and space, in agreement with previous studies.

99 GENERAL AND MISCELLANEOUS↗

Formation of zinc oxide films using submicron zinc particle dispersions

The thermal oxidation of submicron metallic Zn particles was studied as a method to form nanostructured ZnO films. The particles used for this work were characterized by electron microscopy, x-ray diffraction and thermal analysis to evaluate the Zn-ZnO core shell structure, surface morphology, and oxidation characteristics. Significant nanostructural changes were observed for films annealed to 400 °C or higher, where nanoflakes, nanoribbons, nanoneedles and nanorods were formed as a result of stress induced fractures arising in the ZnO outer shell due to differential thermal expansion between the metallic Zn core and the ZnO shell. Mass transport occurs through these defects due to the high vapor pressure for metallic Zn at temperatures above 230 °C, whereupon the Zn vapor rapidly oxidizes in air to form the ZnO nanostructures. The Zn particles were also incorporated into zinc indium oxide precursor solutions to form thin film transistor test structures to evaluate the potential of forming nanostructured field effect sensors using simple solution processing.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Pb nanowire formation on Al/lead zirconate titanate surfaces in high-pressure hydrogen

Thin films of Al on lead zirconate titanate (PZT) annealed in high-pressure hydrogen at 100C exhibit surface Pb nanowire growth. Wire diameter is approximately 80 nm and length can exceed 100 microns. Based on microstructural analysis using electron microscopy and ion scattering, a vapor-solid scheme with hydrogen as a carrier gas was proposed as a growth mechanism. We expect that these observations may lead to controlled Pb nanowires growth through pattering of the Al film.

36 MATERIALS SCIENCE↗

Characterization of Amorphous Zinc Tin Oxide Semiconductors

Amorphous zinc tin oxide (ZTO) was investigated to determine the effect of deposition and post annealing conditions on film structure, composition, surface contamination, and thin film transistor (TFT) device performance. X-ray diffraction results indicated that the ZTO films remain amorphous even after annealing to 600 °C. We found that the bulk Zn:Sn ratio of the sputter deposited films were slightly tin rich compared to the composition of the ceramic sputter target, and there was a significant depletion of zinc at the surface. X-ray photoelectron spectroscopy also indicated that residual surface contamination depended strongly on the sample post-annealing conditions where water, carbonate and hydroxyl species were absorbed to the surface. Electrical characterization of ZTO films, using TFT test structures, indicated that mobilities as high as 17 cm2/Vs could be obtained for depletion mode devices.

Environmental Molecular Sciences Laboratory↗

Three-dimensional Chemical Imaging of Embedded Nanoparticles using Atom Probe Tomography

Analysis of nanoparticles is often challenging especially when they are embedded in a matrix. Hence, we have used laser-assisted atom probe tomography (APT) to analyze the Au-nanoclusters synthesized in situ using ion beam implantation in single crystal MgO matrix. APT analysis along with scanning transmission electron microscopy and energy dispersive spectroscopy (STEM-EDS) indicated that the nanoparticles have an average size ~ 8 - 12 nm. While it is difficult to analyze the composition of individual nanoparticles using STEM, APT analysis can give three dimensional compositions of the same. It was shown that the maximum Au-concentration in the nanoparticles increases with increasing particle size, with a maximum Au-concentration of up to 50%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Monte Carlo simulations of channeling spectra recorded for samples containing complex defects

The main aim of the present paper is to describe the current status of the development of McChasy, a Monte Carlo simulation code, to make it suitable for the analysis of dislocations and dislocation loops in crystals. Such factors like the shape of the bent channel and geometrical distortions of the crystalline structure in the vicinity of dislocation has been discussed. Several examples of the analysis performed at different energies of analyzing ions are presented. The results obtained demonstrate that the new procedure applied to the spectra recorded on crystals containing dislocation yields damage profiles which are independent of the energy of the analyzing beam.

Carlo↗

An Investigation of Hydrogen Depth Profiling Using ToF-SIMS

Hydrogen depth distributions in silicon, zinc oxide and glass are of great interest in material research and industry. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) has been used for hydrogen depth profiling for many years. However, some critical information, such as optimal instrumental settings and detection limits, is not easily available from previous publications. In this work, optimal instrumental settings and detection limits of hydrogen in silicon, zinc oxide and common glass were investigated. The recommended experimental settings for hydrogen depth profiling using ToF-SIMS are: (1) keeping pressure in the analysis chamber as low as possible, (2) using a cesium beam for sputtering and monitoring the H{sup -} signal, (3) employing monatomic ion analysis beams with the highest currents, and (4) using interlace mode. In addition, monatomic secondary ions from a matrix are recommended as references to normalize the H{sup -} signal. Detection limits of hydrogen are limited by pressure of residual gases in the analysis chamber. The base pressure of the analysis chamber (with samples) is about 7 x 10{sup -10} mbar in this study, and the corresponding detection limits of hydrogen in silicon, zinc oxide, and common glass are 1.3 x 10{sup 18} atoms/cm{sup 3}, 1.8 x 10{sup 18} atoms/cm{sup 3}, and 5.6 x 10{sup 18} atoms/cm{sup 3}, respectively.

08 HYDROGEN↗

Structural characterization of epitaxial CrxMo1-x alloy thin films

To develop a model system containing regularly-spaced misfit dislocations for studies of the radiation resistance of nanoscale defects, epitaxial thin films of Cr, Mo, and Cr{sub x}Mo{sub 1-x} alloys were deposited on MgO(001) by molecular beam epitaxy. Film compositions were chosen to vary the lattice mismatch with MgO. The film structure was investigated with x-ray diffraction (XRD), Rutherford backscattering spectrometry (RBS), and scanning transmission electron microscopy (STEM). Epitaxial films with reasonably high crystalline quality and abrupt interfaces were achieved at a relatively low deposition temperature, as confirmed by STEM. However, it was found by XRD and RBS in the channeling geometry that increasing the Mo content of the CrMo alloy films degraded the crystalline quality, despite the improved lattice match with MgO. XRD rocking curve data indicated that regions of different crystalline order may be present within the films with higher Mo content. This is tentatively ascribed to spinodal decomposition into Cr-rich and Mo-rich regions, as predicted by the Cr{sub x}Mo{sub 1-x} phase diagram.

36 MATERIALS SCIENCE↗

Radiation-Induced Reduction of Ceria in Single and Polycrystalline Thin Films

Ceria (CeO{sub 2}) is a technologically important ceramic material with a wide range of neoteric applications in catalysis, solid oxide fuel cells, oxygen gas sensors, hydrogen production, and ultraviolet shielding. Recent research has revealed promising biomedical applications of ceria. Nanoparticles of ceria have been shown to protect healthy cells from radiation-induced cellular damage. The mechanisms governing the radioprotection characteristics of ceria nanoparticles are not well understood and it has been hypothesized that reversible switching between Ce{sup 4+} and Ce{sup 3+} states may enable ceria nanoparticles to mop up free radicals.

08 HYDROGEN↗

Near-surface and bulk behavior of Ag in SiC

The diffusive release of fission products, such as Ag, from TRISO particles at high temperatures has raised concerns regarding safe and economic operation of advanced nuclear reactors. Understanding the mechanisms of Ag diffusion is thus of crucial importance for effective retention of fission products. Two mechanisms, i.e., grain boundary diffusion and vapor or surface diffusion through macroscopic structures such as nano-pores or nano-cracks, remain in debate. In the present work, an integrated computational and experimental study of the nearsurface and bulk behavior of Ag in silicon carbide (SiC) has been carried out. The ab initio calculations show that Ag prefers to adsorb on the SiC surface rather than in the bulk, and the mobility of Ag on the surface is high. The energy barrier for Ag desorption from the surface is calculated to be 0.85~1.68 eV, and Ag migration into bulk SiC through equilibrium diffusion process is not favorable. Experimentally, Ag ions are implanted into SiC to produce Ag profiles buried in the bulk and peaked at the surface. High-temperature annealing leads to Ag release from the surface region instead of diffusion into the interior of SiC. It is suggested that surface diffusion through mechanical structural imperfection, such as vapor transport through cracks in 2 SiC coatings, may be a dominating mechanism accounting for Ag release from the SiC in the nuclear reactor.

Ag↗

Photochemical Properties, Composition, and Structure in Molecular Beam Epitaxy Grown Fe “Doped” and (Fe,N) Codoped Rutile TiO2(110)

We have investigated the surface photochemical properties of Fe "doped" and (Fe,N) co-doped homoepitaxial rutile TiO2 (110) films grown by plasma assisted molecular beam epitaxy. Fe does not incorporate as an electronic dopant in the rutile lattice, but rather segregates to the film surface. However, co-deposition of Fe with N enhances the solubility of Fe, and DFT calculations suggest that co-dopant complex formation is the driving force behind the enhanced solubility. The co-doped films, in which a few atomic percent of Ti (O) are replaced with Fe (N), exhibit significant disorder compared to undoped films grown under the same conditions, presumably due to dopant-induced strain. Co-doping redshifts the rutile bandgap into the visible. However, the film surfaces are photochemically inert with respect to hole-mediated decomposition of adsorbed trimethyl acetate. The absence of photochemical activity may result from dopant-induced trap and/or recombination sites within the film. This study indicates that enhanced visible light absorptivity in TiO2 does not necessarily result in visible light initiated surface photochemistry.

36 MATERIALS SCIENCE↗

LaCrO3 heteroepitaxy on SrTiO3(001) by molecular beam epitaxy

Stoichiometric, epitaxial LaCrO3 films have been grown on TiO2-terminated SrTiO3(001) substrates by molecular beam epitaxy using O2 as the oxidant. Film growth occurred in a layer-by-layer fashion, giving rise to structurally excellent films and surfaces which preserve the step-terrace structure of the substrate. The critical thickness is in excess of 500 Å. Near-surface Cr(III) is highly susceptible to further oxidation to Cr(V), leading to the formation of a disordered phase upon exposure to atomic oxygen. Recovery of the original epitaxial LaCrO3 phase is readily achieved by vacuum annealing.

36 MATERIALS SCIENCE↗