Engineering topics

Siders, C. W.

Publications and source records attributed to Siders, C. W..

4 records

DOE OSTI2023

Enhanced electron acceleration by high-intensity lasers in extended (confined) preplasma in cone targets

Here we report on experimental results from a high-intensity laser interaction with cone targets that increase the number (×3) and temperature (×3) of the measured hot electrons over a traditional planar target. This increase is caused by a substantial increase in the plasma density within the cone target geometry, which was induced by 17 ± 9 mJ prepulse that arrived 1.5 ns prior to the main high intensity (>10 19 W/cm 2 ). Three-dimensional hydrodynamic simulations are conducted using hydra which show that the cone targets create substantially longer and denser plasma than planar targets due to the geometric confinement of the expanding plasma. The density within the cone is a several hundred-micron plasma “shelf” with a density of approximately 10 20 n e /cc. The HYDRA simulated plasma densities are used as the initial conditions for two-dimensional particle-in-cell simulations using EPOCH. These simulations show that the main acceleration mechanism is direct-laser-acceleration, with close agreement between experimentally measured and simulated electron temperatures. Further analysis is conducted to investigate the acceleration of the electrons within the long plasma generated within a compound parabolic concentrator by the prepulse.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Development of a bright MeV photon source with compound parabolic concentrator targets on the National Ignition Facility Advanced Radiographic Capability (NIF-ARC) laser

Compound parabolic concentrator (CPC) targets are utilized at the National Ignition Facility Advanced Radiographic Capability (NIF-ARC) laser to enhance the acceleration of electrons and production of high energy photons, for laser durations of 10 ps and energies up to 2.4 kJ. A large enhancement of mean electron energy (>2 ×) and photon brightness (>10×) is found with CPC targets compared to flat targets. Using multiple diagnostic techniques at different spatial locations and scaling by gold activation spatial data, photon spectra are characterized for E photon = 0.5-30 MeV. Beam width and pointing variations are given. The efficient production of MeV photons at I laser ≈ 2 x 10 18 W/cm 2 with CPCs is observed, with doses of >10 rad in air at 1 m for E photon > 0.5 MeV; these exceed those previously reported with laser-driven sources. Using this source, sub-mm resolution radiographs are generated through large areal density radiograph objects. Hence these results are promising for the development of bright MeV x-ray and particle sources on Petawatt class laser systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Enhancements in laser-generated hot-electron production via focusing cone targets at short pulse and high contrast

We report on the increase in the accelerated electron number and energy using compound parabolic concentrator (CPC) targets from a short-pulse (~150 fs), high-intensity (>10 18 W/cm 2 ), and high-contrast (~10 8 ) laser-solid interaction. We report on experimental measurements using CPC targets where the hot-electron temperature is enhanced up to ~ 9 times when compared to planar targets. The temperature measured from the CPC target is (T e ) = 4.4 ± 1.3 MeV. Using hydrodynamic and particle in cell simulations, we identify the primary source of this temperature enhancement is the intensity increase caused by the CPC geometry that focuses the laser, reducing the focal spot and therefore increasing the intensity of the laser-solid interaction, which is also consistent with analytic expectations for the geometrical focusing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Mirrors for petawatt lasers: Design principles, limitations, and solutions

High intensity and high energy laser facilities place increasing demands on optical components, requiring large surface area optics with exacting specifications. Petawatt lasers are high energy, short-pulse laser systems generally based on chirped-pulse amplification, where an initial low energy short pulse is stretched, amplified, and then recompressed to produce fs to ps high-power laser pulses. In such petawatt lasers, the highest demands are placed on the final optics, including gratings which compress the pulses and mirrors which direct and focus the final high-power beams. The limiting factor in these optical components is generally laser-induced damage. Designing and fabricating these optical components to meet reflection, dispersion, and other requirements while meeting laser-induced damage requirements is the primary challenge discussed in this tutorial. We will introduce the reader to the technical challenges and tradeoffs required to produce mirrors for petawatt lasers and discuss current research directions.

47 OTHER INSTRUMENTATION↗