Search NASA⌕ Search

Engineering topics

Sim, Hyung Sub

Publications and source records attributed to Sim, Hyung Sub.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Considerations for the temperature stratification in a pre-burn constant-volume combustion chamber

In recent years, the Engine Combustion Network (ECN) has developed as a worldwide reference for understanding and describing engine combustion processes, successfully bringing together experimental and numerical efforts. Since experiments and numerical simulations both target the same boundary conditions, an accurate characterization of the stratified environment that is inevitably present in experimental facilities is required. The difference between the core-, and pressure-derived bulk-temperature of pre-burn combustion vessels has been addressed in various previous publications. Additionally, thermocouple measurements have provided initial data on the boundary layer close to the injector nozzle, showing a transition to reduced ambient temperatures. The conditions at the start of fuel injection influence physicochemical properties of a fuel spray, including near nozzle mixing, heat release computations, and combustion parameters. To address the temperature stratification in more detail, thermocouple measurements at larger distances from the spray axis have been conducted. Both the temperature field prior to the pre-combustion event that preconditions the high-temperature, high-pressure ambient, as well as the stratification at the moment of fuel injection were studied. To reveal the cold boundary layer near the injector with a better spatial resolution, Rayleigh scattering experiments and thermocouple measurements at various distances close to the nozzle have been carried out. The impact of the boundary layers and temperature stratification are illustrated and quantified using numerical simulations at Spray A conditions. Next to a reference simulation with a uniform temperature field, six different stratified temperature distributions have been generated. These distributions were based on the mean experimental temperature superimposed by a randomized variance, again derived from the experiments. The results showed that an asymmetric flame structure arises in the computed results when the temperature stratification input is used. In these predictions, first-stage ignition is advanced by 24 $\mu$s , while second-stage ignition is delayed by 11 $\mu$s. At the same time a lift-off length difference between the top and the bottom of up to 1.1 mm is observed. Furthermore, the lift-off length is less stable over time. Given the shown dependency, the temperature data is made available along with the vessel geometry data as a recommended basis for future numerical simulations.

42 ENGINEERING↗
DOE OSTI2022

The role of cool-flame fluctuations in high-pressure spray flames, studied using high-speed optical diagnostics and Large-Eddy Simulations

Here this work investigates the low- and high-temperature ignition and combustion processes, applied to the Engine Combustion Network Spray A flame, combining advanced optical diagnostics and large-eddy simulations (LES). Simultaneous high-speed (50 kHz) formaldehyde (CH 2 0) planar laser-induced fluorescence (PLIF) and line-of-sight OH* chemiluminescence imaging were used to measure the low- and high-temperature flame, during ignition as well as during quasi-steady combustion. While tracking the cool flame at the laser sheet plane, the present experimental setup allows detection of distinct ignition spots and dynamic fluctuations of the lift-off length over time, which overcomes limitations for flame tracking when using schlieren imaging. After significant development to improve LES prediction of the low-and high-temperature flame position, both during the ignition processes and quasi-steady combustion, the simulations were analyzed to gain understanding of the mixture variance and how this variance affects formation/consumption of CH 2 0. Analysis of the high-temperature ignition period shows that a key improvement in the LES is the ability to predict heterogeneous ignition sites, not only in the head of the jet, but in shear layers at the jet edge close to the position where flame lift-off eventually stabilizes. The LES analysis also shows concentrated pockets of CH 2 0, in the center of jet and at 20 mm downstream of the injector (in regions where the equivalence ratio is greater than 6), that are of similar length scale and frequency as the experiment (approximately 5–6 kHz). The periodic oscillation of CH 2 0 match the frequency of pressure waves generated during auto-ignition and reflected within the constant-volume vessel throughout injection. The ability of LES to capture the periodic appearance and destruction of CH 2 0 is particularly important because these structures travel downstream and become rich premixed flames that affect soot production.

42 ENGINEERING↗
DOE OSTI2022

Soot and PAH formation in high pressure spray pyrolysis of gasoline and diesel fuels

Time-resolved soot and PAH formation from gasoline and diesel spray pyrolysis are visualized and quantified using diffuse back illumination (DBI) and laser induced fluorescence (LIF) at 355 nm, respectively, in a constant-volume vessel at 60 bar from 1400 to 1700 K for up to 30 ms. The delay, maximum formation rate, and yield of soot and PAHs are compared across fuels and temperatures and correlated with the yield sooting indices on either the mass or mole basis. The delays generally decrease with increasing temperature, and the formation rates of both PAHs and soot generally increase with temperature. The apparent PAH-LIF yield may decrease with temperature due to PAH growth and conversion into larger species, signal trapping, and thermal quneching. Soot yield generally increases with temperature. The mass-based YSI correlates reasonably well with soot delay, but YSI does not correlate well with soot yield. Here, the mass-based YSI is a more appropriate predictor of sooting propensity than the mole-based YSI.

42 ENGINEERING↗
DOE OSTI2021

Large-Eddy Simulation of Laser-Ignited Direct Injection Gasoline Spray for Emission Control

Large-Eddy Simulations (LES) of a gasoline spray, where the mixture was ignited rapidly during or after injection, were performed in comparison to a previous experimental study with quantitative flame motion and soot formation data [SAE 2020-01-0291] and an accompanying Reynolds-Averaged Navier–Stokes (RANS) simulation at the same conditions. The present study reveals major shortcomings in common RANS combustion modeling practices that are significantly improved using LES at the conditions of the study, specifically for the phenomenon of rapid ignition in the highly turbulent, stratified mixture. At different ignition timings, benchmarks for the study include spray mixing and evaporation, flame propagation after ignition, and soot formation in rich mixtures. A comparison of the simulations and the experiments showed that the LES with Dynamic Structure turbulence were able to capture correctly the liquid penetration length, and to some extent, spray collapse demonstrated in the experiments. For early and intermediate ignition timings, the LES showed excellent agreement to the measurements in terms of flame structure, extent of flame penetration, and heat-release rate. However, RANS simulations (employing the common G-equation or well-stirred reactor) showed much too rapid flame spread and heat release, with connections to the predicted turbulent kinetic energy. With confidence in the LES for predicted mixture and flame motion, the predicted soot formation/oxidation was also compared to the experiments. The soot location was well captured in the LES, but the soot mass was largely underestimated using the empirical Hiroyasu model. An analysis of the predicted fuel–air mixture was used to explain different flame propagation speeds and soot production tendencies when varying ignition timing.

42 ENGINEERING↗