Search NASA⌕ Search

Engineering topics

Simley, Eric

Publications and source records attributed to Simley, Eric.

At least 19 records

Measuring the Effects of Wake Steering With Nacelle-Mounted Scanning Lidar

In large wind plants, wakes from upwind turbines affect downwind turbines by reducing wind speeds and increasing turbulence. Wake steering may mitigate this effect by deflecting the wakes of upwind turbines away from downwind units. Here, we characterize the impact of wakes from yawed turbines at a commercial-scale wind plant under varying atmospheric and turbine operating conditions. Six months of nacelle-based lidar measurements were collected as part of a field campaign in 2019-2020 in the northern US Great Plains to test the effectiveness of wake steering. We separate these lidar scans by atmospheric stability and turbine operating condition to summarize how yawed wind turbine wakes vary with these input parameters in the atmospheric boundary layer. We summarize the impact of wake steering on various wake characteristics including velocity deficit, wake width, and wake center as retrieved from these lidar data. Yawed wakes have significantly different centerline characteristics compared to unyawed wakes, with large regions of meander in the mid wake region. Yawed wakes are also deflected farther than unyawed wakes in less turbulent conditions with velocity deficits persisting further downstream in stable atmospheric conditions. Overall, yawed wind turbine wakes are larger and wider in lower wind speed environments, and yawed wakes are deflected farther in less turbulent conditions, suggesting that wake steering is most effective in stable atmospheric stratification.

17 WIND ENERGY↗

Characterization of wind turbine flow through nacelle-mounted lidars: a review

This article provides a comprehensive review of the most recent advances in the planning, execution, and analysis of inflow and wake measurements from nacelle-mounted wind Doppler lidars. Lidars installed on top of wind turbines provide a holistic view of the inflow and wake characteristics required to characterize and optimize wind turbine performance, carry out model validation and calibration, and aid in real-time control. The need to balance the enhanced capabilities and limitations of lidars compared to traditional anemometers inspired a broad variety of approaches for scan design and wind reconstruction, which we discuss in this review. We give particular emphasis to identifying common guidelines and gaps in the available literature with the aim of providing an exhaustive picture of the state-of-the-art techniques for reconstructing wind plant flow using nacelle-mounted lidars.

17 WIND ENERGY↗

Overview of recent observations and simulations from the American WAKE experimeNt (AWAKEN) field campaign

The American WAKE experimeNt (AWAKEN) is a large-scale field campaign focused on gathering new detailed observations of wind farm–atmosphere interactions for improved understanding of wind farm physics and overall performance. The field campaign, centered around five wind farms in northern Oklahoma, began in September 2022 and will run through at least October 2023. This paper summarizes some of the initial observations and simulations performed as part of the AWAKEN project.

17 WIND ENERGY↗

An independent analysis of bias sources and variability in wind plant pre-construction energy yield estimation methods

The wind resource assessment community has long had the goal of reducing the bias between wind plant pre-construction energy yield assessment (EYA) and the observed annual energy production (AEP). This comparison is typically made between the 50% probability of exceedance (P50) value of the EYA and the long-term corrected operational AEP (hereafter OA P50), and is known as the P50 bias. The industry has critically lacked an independent analysis of bias reduction investigated across multiple consultants to identify the greatest sources of uncertainty and variance in the EYA process and the best opportunities for uncertainty reduction. The present study addresses this gap by benchmarking consultant methodologies against each other and against operational data at a scale not seen before in industry collaborations. We consider data from 10 wind plants and evaluate discrepancies between eight consultancies in the steps taken from estimates of gross to net energy. Consultants tend to overestimate the gross energy produced at the turbines and then compensate by further overestimating downstream losses, leading to a mean P50 bias near zero, still with significant variability among the individual wind plants. Within our data sample, we find that consultant estimates of all loss categories, except environmental losses, tend to reduce the project-to-project variability of the P50 bias. The disagreement between consultants, however, remains flat throughout the addition of losses. Finally, we find that differences in consultants’ estimates of project performance can lead to differences up to $10/MWh in the levelized cost of energy for a wind plant.

Todd, Austin C.↗

Investigating the impact of atmospheric conditions on wake-steering performance at a commercial wind plant

Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to deflect their wakes away from downstream turbines, thereby increasing net energy production. But research suggests that the effectiveness of wake steering strongly depends on atmospheric conditions such as stability. In this paper, we investigate results from a two-turbine wake-steering experiment at a commercial wind plant to assess the impact of stability and five other atmospheric variables on wake-steering performance. Specifically, for different atmospheric condition bins we compare the ability of the controller to achieve the intended yaw offsets, the power gain from wake steering, and the reduction in wake losses. Further, we analyze wake-steering performance as a function of wind speed to eliminate the confounding impact of different wind speed distributions in different atmospheric conditions. Overall, we find that wind direction standard deviation is the best predictor of wake-steering performance, followed by turbulence intensity and turbulent kinetic energy. The results suggest the importance of adapting wake-steering control strategies to different atmospheric conditions.

17 WIND ENERGY↗

Serial-Refine Method for Fast Wake-Steering Yaw Optimization

In this paper we present the Serial-Refine method for quickly finding the optimal yaw angles in wake steering. The method optimizes turbine angles serially from upstream to downstream using a small number of candidate angles. The presented results show that Serial-Refine finds solutions that are at least as good as former conventional optimization approaches but that require much less computation time.

17 WIND ENERGY↗

FLASC (FLORIS-based Analysis for SCADA data)

FLASC provides a rich suite of analysis tools for SCADA data filtering & analysis, wind farm model validation, field experiment design, and field experiment monitoring. The repository is centrally built around NRELs in-house floris wind farm model, available at https://github.com/nrel/floris. FLASC also largely relies on the energy ratio to, among others, quantify wake losses in synthetic and historical data, to perform turbine northing calibrations, and for model parameter estimation.

Fleming, Paul↗

Design of the American Wake Experiment (AWAKEN) field campaign

The American WAKE experimeNt (AWAKEN) is a multi-institutional collaborative field campaign, starting in March 2022, that will gather an unprecedented data set including both atmospheric observations and wind plant operational data. This comprehensive data set will be used to characterize the wind plant performance and turbine loading in different operational and atmospheric conditions and validate the use of different wind plant control strategies and simulation frameworks. An extensive field campaign like AWAKEN requires proper coordination and long-term planning to be successful. In this paper, we review the major activities planned during AWAKEN to provide information for current and future project partners. Specifically, we provide information about the project sites, their planned instruments, and how these will relate to the scientific objectives of the overall AWAKEN project.

17 WIND ENERGY↗

Comparison of the Gaussian Wind Farm Model with Historical Data of Three Offshore Wind Farms

A recent expert elicitation showed that model validation remains one of the largest barriers for commercial wind farm control deployment. The Gaussian-shaped wake deficit model has grown in popularity in wind farm field experiments, yet its validation for larger farms and throughout annual operation remains limited. This article addresses this scientific gap, providing a model comparison of the Gaussian wind farm model with historical data of three offshore wind farms. The energy ratio is used to quantify the model’s accuracy. We assume a fixed turbulence intensity of $I_∞$ = 6% and a standard deviation on the inflow wind direction of $σ_{wd}$ = 3° in our Gaussian model. First, we demonstrate the non-uniqueness issue of $I_∞$ and $σ_{wd}$, which display a waterbed effect when considering the energy ratios. Second, we show excellent agreement between the Gaussian model and historical data for most wind directions in the Offshore Windpark Egmond aan Zee (OWEZ) and Westermost Rough wind farms (36 and 35 wind turbines, respectively) and wind turbines on the outer edges of the Anholt wind farm (110 turbines). Turbines centrally positioned in the Anholt wind farm show larger model discrepancies, likely due to deep-array effects that are not captured in the model. A second source of discrepancy is hypothesized to be inflow heterogeneity. In future work, the Gaussian wind farm model will be adapted to address those weaknesses.

17 WIND ENERGY↗

Experimental results of wake steering using fixed angles

In this article, the authors present a test of wake steering at a commercial wind farm. A single fixed yaw offset, rather than an optimized offset schedule, is alternately applied to an upstream wind turbine, and the effect on downstream turbines is analyzed. This experimental design allows for comparison with engineering wake models independent of the controller's ability to track a varying offset and correctly measure wind direction. Additionally, by applying the same offset in beneficial and detrimental conditions, we are able to collect important data for assessing second-order wake model predictions. Results of the article from collected data show good agreement with the FLOw Redirection and Induction in Steady State (FLORIS) engineering model and offer support for the asymmetry of wake steering predicted by newer models, such as the Gauss–curl hybrid model.

17 WIND ENERGY↗

Results from a wake-steering experiment at a commercial wind plant: investigating the wind speed dependence of wake-steering performance

Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to redirect their wakes away from downstream turbines, thereby increasing the net wind plant power production and reducing fatigue loads generated by wake turbulence. In this paper, we present results from a wake-steering experiment at a commercial wind plant involving two wind turbines spaced 3.7 rotor diameters apart. During the 3-month experiment period, we estimate that wake steering reduced wake losses by 5.6% for the wind direction sector investigated. After applying a long-term correction based on the site wind rose, the reduction in wake losses increases to 9.3%. As a function of wind speed, we find large energy improvements near cut-in wind speed, where wake steering can prevent the downstream wind turbine from shutting down. Yet for wind speeds between 6–8 m/s, we observe little change in performance with wake steering. However, wake steering was found to improve energy production significantly for below-rated wind speeds from 8–12 m/s. By measuring the relationship between yaw misalignment and power production using a nacelle lidar, we attribute much of the improvement in wake-steering performance at higher wind speeds to a significant reduction in the power loss of the upstream turbine as wind speed increases. Additionally, we find higher wind direction variability at lower wind speeds, which contributes to poor performance in the 6–8 m/s wind speed bin because of slow yaw controller dynamics. Further, we compare the measured performance of wake steering to predictions using the FLORIS (FLOw Redirection and Induction in Steady State) wind farm control tool coupled with a wind direction variability model. Although the achieved yaw offsets at the upstream wind turbine fall short of the intended yaw offsets, we find that they are predicted well by the wind direction variability model. When incorporating the expected yaw offsets, estimates of the energy improvement from wake steering using FLORIS closely match the experimental results.

17 WIND ENERGY↗

Wind Plant Performance Prediction Benchmark Phase 1 (Technical Report)

Financial risk resulting from the uncertainty associated with developing, owning, and operating wind power plants remains a barrier to reducing the levelized cost of energy (LCOE). On average, modern wind power plants in the U.S. underperform their expected annual energy output by 3.5-4.5% , with many underperforming by over 10%. To compensate for this uncertainty, investors require a larger return on investment (ROI) and apply "knock-down" factors that mask much of the underlying sources of uncertainty. Wind energy projects thus have reduced access to low-cost capital. Furthermore, operating wind plants often take a simple approach to estimating operations & maintenance (O&M) costs (e.g. straight-line estimates based on similar plants), which can eat into profits. To overcome these issues, the wind industry must improve the models they use for estimating wind plant performance and operations. An industry consortium (IC) requested that the National Renewable Energy Laboratory (NREL) lead a Department of Energy (DOE) working group to benchmark the accuracy of wind power plant energy predictions against real operational data. The IC was also motivated by DOE and NREL's potential to characterize systematic energy underperformance, identify sources of uncertainty, and explore root causes. The Wind Plant Performance Prediction (WP3) project was created out of this request, and this report represents the successful completion of Phase 1 of the WP3 project. During the project, wind plant owners provided both pre-construction and operational data to NREL. The pre-construction data was provided to wind resource assessment (WRA) consultants so they could conduct energy yield assessments (EYA). NREL took all of the completed EYAs, along with the operational data, and conducted an operational assessment to benchmark the EYA results against actual operational data. Given the large amounts of sensitive data required for this effort, as well as historical opposition to sharing data within industry, successful completion of Phase 1 represents an unprecedented milestone for industry data sharing. To improve the accuracy and confidence of pre-construction EYAs, wind plant owners and investors need better, more certain, energy yield predictions. The WP3 Benchmark Project is an industry-driven response to this reality. For the first time, industry has taken the important step of working together at scale, sharing valuable operational data with DOE and NREL in order to investigate the sources of bias and uncertainty in these energy estimates. This IC provides wind plant preconstruction and operational data to NREL in an organized and documented fashion and provides guidance and feedback as needed. The IC also provides introspection of the design of experiment, key metrics of success, data challenges, analysis best practices, and quality of results.

17 WIND ENERGY↗

Control-Oriented Model for Secondary Effects of Wake Steering

This paper presents a model to incorporate the secondary effects of wake steering in large arrays of turbines. Previous models have focused on the aerodynamic interaction of wake steering between two turbines. The model proposed in this paper builds on these models to include yaw-induced wake recovery and secondary steering seen in large arrays of turbines when wake steering is performed. Turbines operating in yaw-misaligned conditions generate counter-rotating vortices that entrain momentum and contribute to the deformation and deflection of the wake at downstream turbines. Rows of turbines can compound the effects of wake steering that benefit turbines far downstream. This model quantifies these effects and demonstrates that wake steering has greater potential to increase the performance of a wind farm due to these counter-rotating vortices especially for large rows of turbines. This is validated using numerous large-eddy simulations for three-turbine, five-turbine, and wind farm scenarios.

17 WIND ENERGY↗

Lowering post‐construction yield assessment uncertainty through better wind plant power curves

Abstract Many operational analyses of wind power plants require a statistical relationship, which can be called the wind plant power curve, to be developed between wind plant energy production and concurrent atmospheric variables. Currently, a univariate linear regression at monthly resolution is the industry standard for post‐construction yield assessments. Here, we evaluate the benefits in augmenting this conventional approach by testing alternative regressions performed with multiple inputs, at a finer time resolution, and using nonlinear machine‐learning algorithms. We utilize the National Renewable Energy Laboratory's open‐source software package OpenOA to assess wind plant power curves for 10 wind plants. When a univariate generalized additive model at daily or hourly resolution is used, regression uncertainty is reduced, in absolute terms, by up to 1.0 % and 1.2 % (corresponding to a −59 % and −80 % relative change), respectively, compared to a univariate linear regression at monthly resolution; also, a more accurate assessment of the mean long‐term wind plant production is achieved. Additional input variables also reduce the regression uncertainty: when temperature is added as an input to the conventional monthly linear regression, the operational analysis uncertainty connected to regression is reduced, in absolute terms, by up to 0.5 % (−43 % relative change) for wind power plants with strong seasonal variability. Adding input variables to the machine‐learning model at daily resolution can further reduce regression uncertainty, with up to a −10 % relative change. Based on these results, we conclude that a multivariate nonlinear regression at daily or hourly resolution should be recommended for assessing wind plant power curves.

17 WIND ENERGY↗

Aeroacoustic Assessment of Wind Plant Controls

The Aeroacoustic Assessment project aims to quantify changes in aeroacoustic noise generation by a utility scale wind turbine operating under imposed yaw offsets common for wake steering and wind plant control strategies. Active plant control utilizing wake deflection control strategies have been shown experimentally and computationally to reliably produce 1-2% of additional annual energy production (AEP) without significant changes in turbine structural loads, the potential impact on aeroacoustic emissions has yet to be quantified or completely understood. Yawed operation of a wind turbine changes the three-dimensional aerodynamic interaction between the rotor blades and the incoming atmospheric flow, leading to changes in noise generation. This work quantifies the extent to which active control induces additional aeroacoustic emissions from additional separation and other flow interaction dynamic effects. Given public concerns about wind turbine noise and the need for observational data required for regulators to establish noise restrictions, we must understand potential acoustic emissions resulting from active control prior to commercial deployment and the development of practical noise reduction methods and technologies. The work outlined in this report details the new aeroacoustic measurement capability developed at NREL and its application to making full-field observations of noise from a utility-scale wind turbine. Preliminary noise modeling with the aeroacoustics module in OpenFAST helped to establish the design of the experiment, specifically targeting the noise observed at observers distributed around the DOE-owned GE 1.5 MW wind turbine. Low-frequency and infrasound measurement capability implemented in this project establish an operational baseline for the wind turbine, setting the stage for future control, rotor blade, and turbine design research.

17 WIND ENERGY↗

Power increases using wind direction spatial filtering for wind farm control: Evaluation using FLORIS, modified for dynamic settings

As wind energy plays a growing role in the energy sector, new methods for controlling wind turbines and wind farms to maximize performance are garnering industry interest. A developing body of research treats the entire wind farm as a control system, with individual turbines acting as agents in a network, allowing farm-level objectives to be considered. Two promising developments in this research are wake steering control, which seeks to increase the power generated at a wind farm by directing the wakes of upstream turbines away from downstream ones, and communication-based spatial filtering, which seeks to improve the quality of information used by turbine- and farm-level controllers by combining measurements of the wind field collected at the individual turbines. The latter method has been shown to improve the estimates of wind direction at the turbines; however, the resulting potential for increased power capture warrants further investigation. With this paper, we begin to address this gap by combining wake steering with wind direction spatial filtering. To do so, we present a preliminary method for assessing the power capture of dynamic controllers using wind farm codes designed for time-averaged simulation. This allows us to generate results much more rapidly than would be possible using high-fidelity wind farm simulators and may be useful in many wind farm control design applications.

17 WIND ENERGY↗

OpenOA: An Open-Source Codebase For Operational Analysis of Wind Farms

OpenOA is an open source framework for operational data analysis of wind energy plants, implemented in the Python programming language. OpenOA provides a common data model, high level analysis workflows, and low-level convenience functions that engineers, analysts, and researchers in the wind energy industry can use to facilitate analytics workflows on operational data sets. OpenOA contains documentation, worked out examples in Jupyter notebooks, and a corresponding example dataset from the Engie Renewable’s La Haute Borne Dataset.

17 WIND ENERGY↗