Search NASA⌕ Search

Engineering topics

Simmonds, M. J.

Publications and source records attributed to Simmonds, M. J..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Reduced defect recovery in self-ion damaged W due to simultaneous deuterium exposure during annealing

Deuterium (D) plasma exposure during annealing of self-ion damaged tungsten (W) is shown to exhibit reduced defect recovery when compared to annealing without D plasma exposure. In these experiments, samples were first damaged with 20 MeV W ions. Next, samples were annealed either with or without simultaneous D 2 plasma exposure. The simultaneous annealed samples were first decorated by D 2 plasma at 383 K prior to ramping up to an annealing temperature of 473, 573, 673, or 773 K and held for 1 h with concurrent plasma exposure. The vacuum annealed samples each had a corresponding temperature history but without D 2 plasma treatment. Finally, all samples were exposed to D 2 plasma at 383 K to decorate any remaining defects. Nuclear reaction analysis and thermal desorption spectroscopy (TDS) shows that the simultaneous plasma-exposed and annealed samples exhibited virtually no defect recovery at annealing temperatures of up to 673 K, and had higher D retention than found in the vacuum annealed samples. TDS results indicate that only the lowest detrapping energy defects recover at an 773 K anneal for the simultaneous plasma annealed samples, while the vacuum annealed samples showed defect recovery at all anneal temperatures. Furthermore, this experiment clearly demonstrates that D occupied defects can significantly reduce or eliminate defect annealing in W, and is consistent with the existence of synergistic plasma exposure/displacement damage effects in fusion-energy relevant plasma facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Characterizing the plasma-induced thermal loads on a 200 kW light-ion helicon plasma source via infra-red thermography

The light-ion helicon plasma source of the Proto-MPEX linear plasma device has been recently upgraded to enable pulsed (0.5–1 s) operation up to 200 kW. The main objective of this work is to report on the plasma-induced surface heat fluxes incident on the helicon window during high power operation (60–150 kW net power) for the purpose of the design of the upcoming material plasma exposure eXperiment (MPEX). The IR imaging system and associated physics models for the extraction of surface heat fluxes are presented. Furthermore, experimental results demonstrate that the control of the plasma strike point via magnetic flux mapping and the use of dedicated limiters is effective at reducing the heat loads on the dielectric window. Moreover, it is found that the flux mapping must create a gap between the plasma and the dielectric window of at least the plasma radial decay length. Extrapolated to 200 kW net RF power, this mode of operation can reduce the power lost to the dielectric window by 33%. The results presented have direct application to the design of high-powered helicon plasma sources that operate in a steady state. Examples include linear divertor simulators such as MPEX, electric thrusters, negative ion sources for NBI and linear plasma–material interaction test stands.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

TMAP modeling of D release from baked multi-layer Be–D co-deposits

Single-layer Beryllium–Deuterium (Be–D) co-deposits were analyzed using Thermal Desorption mass Spectrometry (TDS) as outlined in the companion paper. This work details the TMAP modeling and the analysis of selected samples that received double-layer (DL) coatings to study co-deposit thickness and prior bake effects. Here, TDS data were simulated with detrap energies 0.8, 0.9, and 1.0 eV. In DLs formed at 393 K, modeling revealed that under-layers baked at 623 K for either 2 or 20 h had little pumping effect on over-layers, suggesting empty trap removal during bake. Extrapolated to ITER, data and analysis suggest less impact on the ongoing ITER bake efficiency than previously predicted.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Deuterium retention in Be-D co-deposits formed over an ITER relevant parameter space

Be-D co-deposit samples are produced over an extended range of plasma-material interaction parameters reflective of the conditions expected in ITER deposition dominant locations. Deposition temperature, D impact energy, atomic Be deposition rate, and D2 neutral pressure were varied in the ranges 373–623 K, ~2–100 eV, 1–10 × 10 19 m 2 s –1 , and 0.27–13.3 Pa respectively. Thermal desorption spectrometry was carried out on samples, subsequently, to measure the D release profile and retention. In this work, it was found that the D retention in samples agrees well with the existing GDT D/Be scaling over the extended parameter space, and that increased D impact energy and D2 pressure can lead to the observation of a sharp low-temperature release peak at ~440 K in desorption data. Desorption data without the presence of the sharp release mechanism are modeled with TMAP-7 utilizing three traps of de-trapping energies, 0.8, 0.9 and 1.0 eV.

36 MATERIALS SCIENCE↗