Engineering topics

Simos, Nikolaos

Publications and source records attributed to Simos, Nikolaos.

9 records

DOE OSTI2021

Radiation damage of a two-dimensional carbon fiber composite (CFC)

Carbon fiber composites (CFC) are, among other applications, already in use as low-impedance collimating elements for intercepting TeV-level protons machines, like the CERN Large Hadron Collider. Towards a comprehensive understanding of these materials’ properties and behavior, a series of radiation damage campaigns have been undertaken in order to quantitively investigate the response of AC-150 K CFC to high proton fluences. The CFCs dimensional changes, stability, micro-structural evolution, and structural integrity below and above 5 × 10 20 p/cm 2 fluence threshold were studied. The irradiating particles were protons of kinetic energies in the range of 130–200 MeV. The effects of the irradiation temperature (~90–180°C and 280–500°C) combined with the proton fluence on the dimensional stability and the microstructural evolution of this anisotropic two-dimensional composite structure were studied using precision dilatometry and X-ray diffraction. Our results shed light on the fluence-based limitations for these composite materials. Furthermore, we compare these results with reference unirradiated graphite, and we discuss the similarities and differences in the dimensional changes and post-irradiation annealing properties.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Tensile behavior of dual-phase titanium alloys under high-intensity proton beam exposure: radiation-induced omega phase transformation in Ti-6Al-4V

A high-intensity proton beam exposure with 181 MeV energy has been conducted at Brookhaven Linac Isotope Producer facility on various material specimens for accelerator targetry applications, including titanium alloys as a beam window material. The radiation damage level of the analyzed capsule was 0.25 dpa at the beam center region with an irradiation temperature around 120 oC. Tensile tests showed increased hardness and a large decrease in ductility for the dual a+ß-phase Ti-6Al-4V Grade-5 and Grade-23 extra low interstitial alloys, with the near a-phase Ti-3Al-2.5V Grade-9 alloy still exhibiting uniform elongation of a few % after irradiation. Transmission Electron Microscope analyses on Ti-6Al-4V indicated clear evidence of a high-density of defect clusters with size less than 2 nm in each a-phase grain. The ß-phase grains did not contain any visible defects such as loops or black dots, while the diffraction patterns clearly indicated ?-phase precipitation in an advanced formation stage. The radiation-induced ?-phase transformation in the ß-phase could lead to greater loss of ductility in Ti-6Al-4V alloys in comparison with Ti-3Al-2.5V alloy with less ß-phase.google scho

Tensile Test, titanium, acclerator, proton beam↗

DOE OSTI2020

Low-temperature proton irradiation damage of isotropic nuclear grade IG-430 graphite

IG-430, a fine-grained, isotropic graphite grade is a promising candidate for the future Very High Temperature Reactors (VHTR). IG-430 which provides higher density, strength, and thermal conductivity, has already been developed as a graphite for next-generation HTGR, and is expected to be employed. This graphite grade, however, is lacking enough database that is needed for design. The present study aims to enhance the database with experimental data focusing on the low temperature regime (90–210 °C) by using 120–200 MeV protons to irradiate the IG-430 graphite to peak fluence of ~1.2 10 25 m –2 . It is anticipated that radiation-induced changes in the graphite properties and damage to be more pronounced in this low temperature regime than in elevated temperatures where damage annealing is taking place simultaneously. IG-430 graphite was characterized following irradiation for mechanical property changes (modulus and strength), dimensional stability and irradiation-induced growth as well as microstructural changes using high energy X-rays and different X-ray diffraction techniques. In assessing proton irradiation effects on the IG-430 graphite grade, comparison of radiation effects was made with the IG-43 grade, the un-purified version of IG-430, as well as other isotropic graphite grades. IG-430 was shown in this study to be better graphitized than other isotropic graphite grades. The study also revealed that during proton irradiation at low temperatures (~100 °C) the IG-430 exhibits stored energy release.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Hexagonal boron nitride (h-BN) irradiated with 140 MeV protons

Here, hexagonal boron nitride was irradiated with 140 MeV protons to a fluence of ~6 10 20 p/cm 2 at T irr ~200 °C. Isotropic graphite was also irradiated alongside h-BN under similar conditions and fluence to enable direct comparison of the two similar structures. The effects of proton irradiation on dimensional stability and microstructure were studied using precision dilatometry and energy dispersive Xray diffraction techniques revealing by direct comparison to graphite that h-BN can better resist radiation damage from bombardment when irradiated with protons impinging normal to the crystallographic planes or along the crystallographic c-axis. X-ray diffraction experiments also revealed a preferred orientation of the crystallites in bulk samples near the sample surface, an orientation influenced by irradiation. Thermal studies using differential scanning calorimetry and thermogravimetric analysis to 740 °C, augmented by precision dilatometry, provided evidence of subtle phase transitions attributed to residual w-BN in the matrix. Irradiation appears to induce shifting of such transitions.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Failure investigation of nuclear grade POCO graphite target in high energy neutrino physics through numerical simulation

In many high energy physics neutrino beamlines, targets are made up of isotropic POCO graphite grade for production of neutrinos for high energy particle physics research and are bombarded with highly energetic pulsed proton beam. The pulsed proton beam with a small beam size creates thermal stress waves as well as radiation damage such as displacement damage, void formation, swelling, and gas formation amongst others. As a result, after a few years of operation one of the longest operated targets appears to have undergone bulk swelling and fractured along the beam centerline. A complex interaction of dynamic loading due to beam, material degradation due to irradiation are thought to have caused such a failure. Here, we present a numerical simulation to capture the combined effects of swelling and the dynamic effect of thermal stress waves due to beam heating, to explain the failure of target. An empirical formula has been developed to take into account swelling as a function of temperature and proton fluence and has been implemented in a commercial finite element code. Extensive X-ray diffraction (XRD) were performed on graphite samples from the failed target to understand the lattice parameter changes due to irradiation and build a valid empirical model. Simulation results show that swelling plays a major role in elevating the stress state in the material exceeding the failure strength while the pulsed beam heating also introduces fatigue loading that would explain brittle fracture emanating from inside of the material and propagating outward. Such empirical formulations will help in identifying the threshold values of critical parameters to extend the service life of future multi-megawatt neutrino targets and targets in other accelerator environments.

43 PARTICLE ACCELERATORS↗

DOE OSTI2020

Fast Neutron Irradiation Embrittlement-ductilitization of an Iron-based Amorphous Alloy using In Situ Synchrotron X-ray Diffraction

Amorphous Fe-based nanostructured alloy coatings thermally sprayed on bcc steel substrate, were subjected to neutron irradiation doses up to 2 × 10 19 n/cm 2 . It is shown that the interplay between embrittlement and recovery of ductility is governed by amorphous to crystallization transition and phase decomposition in which temperature and irradiation dose have reciprocal effects. Microscopic (X-ray diffraction) observations on the behavior of the amorphous Fe-based alloy are correlated with relevant macroscopically observed mechanical behavior. It is shown that amorphous Fe-based alloy coatings maintain and even enhance their amorphous structure with irradiation, exhibit radiation-induced restoration of thermally-induced embrittlement and finally exhibit resistance to ductility loss up to the fluence of 2 × 10 18 n/cm 2 and good thermal stability up to 350 °C. The latter is deduced from X-ray diffraction experiments of in-situ tensile strain application on the irradiated coating.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Radiation Damage Studies on Titanium Alloys as High Intensity Proton Accelerator Beam Window Materials

A high-strength dual a+ß phase titanium alloy Ti–6Al–4V is utilized as a material for beam windows in several accelerator target facilities. However, relatively little is known about how material properties of this alloy are affected by high-intensity proton beam irradiation. With plans to upgrade neutrino facilities at J-PARC and Fermilab to over 1 MW beam power, the radiation damage in the window material will reach a few displacements per atom (dpa) per year, significantly above the ~0.3 dpa level of existing data. The international RaDIATE collaboration, Radiation Damage In Accelerator Target Environments, has conducted a high intensity proton beam irradiation of various target and window material specimens at Brookhaven Linac Isotope Producer (BLIP) facility, including a variety of titanium alloys. Post-Irradiation Examination (PIE) of the specimens in the 1st capsule, irradiated at up to 0.25 dpa, is in progress. Tensile tests in a hot cell at Pacific Northwest National Laboratory (PNNL) exhibited a clear signature of radiation hardening and loss of ductility for Ti–6Al–4V, while Ti–3Al–2.5V, with less ß phase, exhibited less severe hardening. Microstructural investigations will follow to study the cause of the difference in tensile behavior between these alloys. High-cycle fatigue (HCF) performance is critical to the lifetime estimation of beam windows exposed to a periodic thermal stress from a pulsed proton beam. The first HCF data on irradiated titanium alloys are to be obtained by a conventional bend fatigue test at Fermilab and by an ultrasonic mesoscale fatigue test at Culham Laboratory. Specimens in the 2nd capsule, irradiated at up to ~1 dpa, cover typical titanium alloy grades, including possible radiation-resistant candidates. These systematic studies on the effects of radiation damage of titanium alloy materials are intended to enable us not only to predict realistic lifetimes of current beam windows made of Ti–6Al–4V, but also to extend the lifetime by choosing a more radiation and thermal shock tolerant alloy with a preferable heat treatment, or even by developing new materials.

Titanium Alloy, Beam Window, Proton Beam, Radiatio↗

DOE OSTI2019

NSLS-II Ground Vibration Stability Studies and Design Implementation

We report that next-generation synchrotron accelerator facilities pushing the envelope of resolution to just a few nanometers and possibly atomic scale (~1 nm) require extreme stability of their experimental setting. Such stability is greatly influenced by the background micro-seismic activity and natural disturbance sources that are present throughout the globe and the cultural, man-made noise stemming from traffic on nearby highways and railways, operating machinery, and other activities. Defenses against such negatively impacting environment include smart conventional design of facilities, isolation of experiments, careful consideration of the selected site by providing ample distance from sources or protection by depth and, most importantly, qualification/quantification of the ground vibration environment both in terms of amplitude and spectral characteristics. Qualification and quantification of the site-specific noise environment may be utilized in the implementation of defense features in the design of the facility and high-sensitivity experiments. The performance is measured by the adherence to specific stability criteria that are ever-demanding, given the nature of the experiments that are sought where resolution down to a few nanometers is required. Furthermore, the selection of the optimal site and the quantification of the unavoidable background noise are important aspects to be considered in assessing the performance of such facilities.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Synchrotron Facilities: Vibration and Stability Challenge

The new generation of synchrotron accelerator facilities are opening exciting new opportunities in imaging, spectroscopy, structural and dynamic studies, and other applications by pushing the envelope of resolution to just a few nanometers and possibly atomic scale (~1 nm). Achieving such a state of resolution in both space and energy is expected to have broad impact on a wide range of disciplines and scientific initiatives in the coming decades, including new studies of small crystals in structural biology, a wide range of nanometer-resolution probes for nanoscience, properties of materials under extreme conditions, etc. Such performance goals place severe requirements on the quality of the electron and photon beams. Within the synchrotron accelerator envelope, and in addition to the need to maintain the electron beam within an extremely stable orbit in order to realize the benefits of the high brightness and small beam sizes, it is essential that the photon beams are also exceedingly stable in both position and angle. Particularly for timing experiments, it is also necessary that the arrival-time jitter of the bunch be small. Transverse beam motions <10% of beam size or angular spread, and longitudinal beam motion of <5% of equilibrium bunch duration, are typically desired. Ideally, the temporal, spatial, and angular stability of the electron beam should be maintained for at least the duration of spectral scans, which typically run from a few milliseconds to a few hours. Achieving such a level of stability that is ever pushing the envelope is an enormous task, and that is where engineering comes into play.

36 MATERIALS SCIENCE↗