Search NASA⌕ Search

Engineering topics

Simpson, Michael F

Publications and source records attributed to Simpson, Michael F.

Investigation of Fission Product Transport into Zeolite-A for Pyroprocessing Waste Minimization

Methods to improve fission product salt sorption into zeolite-A have been investigated in an effort to reduce waste associated with the electrochemical treatment of spent nuclear fuel. It was demonstrated that individual fission product chloride salts were absorbed by zeolite-A in a solid-state process. As a result, recycling of LiCl-KCl appears feasible via adding a zone-freezing technique to the current treatment process. Ternary salt molten-state experiments showed the limiting kinetics of CsCl and SrCl2 sorption into the zeolite. CsCl sorption occurred rapidly relative to SrCl2 with no observed dependence on zeolite particle size, while SrCl2 sorption was highly dependent on particle size. The application of experimental data to a developed reaction-diffusion-based sorption model yielded diffusivities of 8.04 × 10-6 and 4.04 × 10-7 cm2 /s for CsCl and SrCl2, respectively. Additionally, the chemical reaction term in the developed model was found to be insignificant compared to the diffusion term.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Selective Reduction of Active Metal Chlorides from Molten LiCl-KCl using Lithium Drawdown

In support of optimizing electrorefining technology for treating spent nuclear fuel, lithium drawdown has been investigated for separating actinides from molten salt electrolyte. Drawdown reaction selectivity is a major issue that needs to be investigated, since the goal is to remove actinides while leaving the fission products in the salt. A series of lithium drawdown tests with surrogate fission product chlorides was run to obtain selectivity data with non-radioactive salts, develop a predictive model, and draw conclusions about the viability of using this process with actinide-loadd salt. Results of tests with CsCl, LaCl3, CeCl3, and NdCl3 are reported here. An equilibrium model has been formulated and fit to the experimental data. Excellent fits to the data were achieved. Based on analysis and results obtained to date, it is concluded that clean separation between minor actinides and lanthanides will be difficult to achieve using lithium drawdown.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Uncertainty Studies of Real Anode Surface Area in Computational Analysis for Molten Salt Electrorefining

This study examines how much cell potential changes with five differently assumed real anode surface area cases. Determining real anode surface area is a significant issue to be resolved for precisely modeling molten salt electrorefining. Based on a three-dimensional electrorefining model, calculated cell potentials compare with an experimental cell potential variation over 80 hours of operation of the Mark-IV electrorefiner with driver fuel from the Experimental Breeder Reactor II. We succeeded to achieve a good agreement with an overall trend of the experimental data with appropriate selection of a mode for real anode surface area, but there are still local inconsistencies between theoretical calculation and experimental observation. In addition, the results were validated and compared with two-dimensional results to identify possible uncertainty factors that had to be further considered in a computational electrorefining analysis. These uncertainty factors include material properties, heterogeneous material distribution, surface roughness, and current efficiency. Zirconium's abundance and complex behavior have more impact on uncertainty towards the latter period of electrorefining at given batch of fuel. The benchmark results found that anode materials would be dissolved from both axial and radial directions at least for low burn-up metallic fuels after active liquid sodium bonding was dissolved.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Computational Model of the Mark-IV Electrorefiner: Two-Dimensional Potential and Current Distributions

A computational model of the Mark-IV electrorefiner is currently being developed as a joint project between Idaho National Laboratory, Korea Atomic Energy Research Institute, Seoul National University, and the University of Idaho. As part of this model, the two-dimensional potential and current distributions within the molten salt electrolyte are calculated for U3+ , Zr4+ , and Pu3+ along with the total distributions, using the partial differential equation solver of the commercial Matlab software. The electrical conductivity of the electrolyte solution is shown to depend primarily on the composition of the electrolyte and to average 205 mho/m with a standard deviation of 2.5 × 10-5% throughout the electrorefining process. These distributions show that the highest potential gradients (thus, the highest current) exist directly between the two anodes and cathode. The total, uranium, and plutonium potential gradients are shown to increase throughout the process, with a slight decrease in that of zirconium. The distributions also show small potential gradients and very little current flow in the region far from the operating electrodes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SCALE UP OF CERAMIC WASTE FORMS FOR THE EBR-II SPENT FUEL TREATMENT PROCESS

ABSTRACT SCALE UP OF CERAMIC WASTE FORMS FOR THE EBR-II SPENT FUEL TREATMENT PROCESS Matthew C. Morrison, Kenneth J. Bateman, Michael F. Simpson Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415 The ceramic waste process is the intended method for disposing of waste salt electrolyte, which contains fission products from the fuel-processing electrorefiners (ER) at the INL. When mixed and processed with other materials, the waste salt can be stored in a durable ceramic waste form (CWF). The development of the CWF has recently progressed from small-scale testing and characterization to full-scale implementation and experimentation using surrogate materials in lieu of the ER electrolyte. Two full-scale (378 kg and 383 kg) CWF test runs have been successfully completed with final densities of 2.2 g/cm3 and 2.1 g/cm3, respectively. The purpose of the first CWF was to establish material preparation parameters. The emphasis of the second pre-qualification test run was to evaluate a preliminary multi-section CWF container design. Other considerations were to finalize material preparation parameters, measure the material height as it consolidates in the furnace, and identify when cracking occurs during the CWF cooldown process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Salt-Zeolite Ion Exchange Equilibrium Studies for Complete Set of Fission Products in Molten LiCl-KCl

This paper presents results on LiCl-KCl based molten salts/zeolite-A contact experiments and the associated equilibrium ion exchange model. Experiments examine the contact behaviors of various ternary salts (LiCl-KCl-YCl3, LiCl-KCl-LaCl3, and LiCl-KCl-PrCl3) and quaternary salts (LiCl-KCl-CsCl-NdCl3 and LiCl-KCl-CsCl-SrCl2) with the zeolite-A. The developed equilibrium model assumes that there are ion exchange and occlusion sites, both of which are in equilibrium with the molten salt phase. A systematic approach in estimating total occlusion capacity of the zeolite-A is developed. The parameters of the model, including the total occlusion capacity of the zeolite-A, were determined from fitting experimental data collected via multiple independent studies including the ones reported in this paper. Experiments involving ternary salts were used for estimating the parameters of the model, while those involving quaternary salts were used to validate the model.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Nuclear Fuel Reprocessing

This is an a submission for the Encyclopedia of Sustainable Technology on the subject of Reprocessing Spent Nuclear Fuel. No formal abstract was required for the article. The full article will be attached.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗